Question about 1996 Chevrolet C1500

Open Question

How do you remove the clutch slave cylinder on a 1996 c1500 standard transmission

I am replacing the clutch pack on my 1996 c1500 and I can not get the line off of the clutch slave cylinder. I do I remove it from the transmission ?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

co7196
  • 3433 Answers

SOURCE: CLUTCH LINE LEAK AT HOSE FITTING AT SLAVE CYLINDER

Use a copper washer like on the brake lines, not an o ring.

Posted on Jun 02, 2009

  • 145 Answers

SOURCE: after replacing starter and removing slave cylinder, clutch fails to work

sounds like you have a air pocket or you fail to engage the slave cylinder push rod If you disconnected the slave cylinder from the hose proceed to bleed out the slave cylinder if you didn't take you slave cylinder and whit out disconnecting the hose and make sure the push rod is against the clutch push arm.

Posted on Jun 13, 2009

juncro
  • 467 Answers

SOURCE: How do I disconnect the line between the slave and

its best to used a wise grip.

Posted on Jul 23, 2009

  • 2187 Answers

SOURCE: clutch slave cylinder replacement or repair -

You will have to replace the rubber and the piston like mechanism to get this done. If you found an assembly replacement for the entire clutch slave, the better. The leaks may be caused by faulty rubber or valve on the piston but this can be caused by the linings of the cylinder becoming rough due to wear and tear.

Posted on Aug 20, 2009

  • 157 Answers

SOURCE: Clutch pedal does not disengage clutch

If the car hasn't been driven for a while it could be corrosion on the fork but I think that is unlikely. I think you are right about the release bearing being jammed in the spring. If the truck has quite high mileage, it probably means a clutch job.

Posted on Feb 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to find 1996 clutch slave cylinder's location


old post but there are 2 post now.
so...
FSM quote:
On 1996-99 vehicles the slave cylinder is called a concentric slave cylinder. It is located on the inside of the transmission bell housing on the input shaft. Removal of the transmission is required to replace it. It directly engages the clutch release bearing.

May 19, 2014 | Isuzu Hombre Cars & Trucks

1 Answer

My 91 chevy c1500 clutch has stopped


The slave cylinder on the transmission is leaking. It may be rebuilt or replaced. It will have to have the air bled out of it either way you go. The bleeder screw in on the side if the slave cylinder .

Apr 18, 2012 | 1991 Chevrolet C1500

2 Answers

Where is the 1999 Saturn SL2 slave cylinder located?


on a manual transmission the Clutch Slave Cylinder is located on the drivers side front of the transmission. You can locate it by first finding the clutch master cylinder on the drivers side of the firewall. Then fallow the plastic line to the front of the transmission.

To remove the slave you will first twist it then pull it out of the transmission.

The clutch slave and mater cylinder are replaced as an assembly.

Oct 07, 2011 | 1999 Saturn SL

1 Answer

I have a 1996 Isuzu Hombre. I have had to bleed the clutch a few times lately. Today something gave in and I lost all pressure. No fluid leaking from slave cylinder area but the reservior was empty. There...


Hello buiskit: My name is Roger and I will help you. If the fluid runs down the firewall or leaks down on the floor board or on your foot. The problem should be the clutch master cylinder. However should the fluid leak at the bell housing area.Then the problem is the slave cylinder. To replace the slave cylinder you will need to pull the transmission in order to replace the slave cylinder. Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Jul 22, 2011 | Isuzu Hombre Cars & Trucks

1 Answer

In spite of clutch pushed in all the way, the gears will not shift into any gear. Any ideas of how this problem might be solved?


Your clutch is not working. It is a hydraulic system just like brakes. If the fluid has leaked out , or gotten low enough to allow air in the system , the clutch will not work. The system can be refilled and bled of air , however , most likely it will just leak again. The leak can be in the master cylinder , which is easily replaceable , or it could be in the slave cylinder , which is a bigger job.
Many modern cars have an internal slave cylinder which means it is inside of the transmission bell housing , and unfortunately , the transmission has to be removed from the car to replace the part.
Some cars have the slave cylinder mounted externally which is an easier fix.
I CHECKED A PARTS SUPPLIER and found that if your car has the 3.0 L engine , the slave cylinder looks to be the externally mounted version , which is good news.

Jan 29, 2011 | 1996 Nissan Maxima

1 Answer

1996 f250 5 speed manual. Clutch must be to the floor before I can get it into gear. Is this normal?


No, your clutch is controlled by a slave cylinder and clutch master cylinder. Check your clutch master cylinders fluid level first, if its high, your clutch is starting to wear down. Next, on the bottom of your transmission there will be an inspection cover, remove and check with a suitable flashlight if the clutch slave cylinder is leaking, if so, replace both clutch master cylinder and cslave cylinder. Stay away from slave cylinders that you have to build yourself such as those at autozone! Bleeding of these components will be required.

Oct 09, 2009 | 1996 Ford F250 Crew Cab

1 Answer

Clutch went out


Unfortunately if the clutch pack has failed there is really no option but to remove the transmission.

Dec 02, 2008 | 1990 Acura Legend

1 Answer

Clutch problem,where is the slave cylinder located


The clutch slave cylinder is located on the left side of the transmission, but i believe that the slave cylinder may come with the master cylinder and lines already attached

Aug 20, 2008 | 1996 Dodge Ram 1500 Club Cab

Not finding what you are looking for?
1996 Chevrolet C1500 Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...