Question about 1997 Chevrolet S-10 Pickup

Open Question

Torque specs water pump

Water pump to engine torque

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

johnny5846
  • 379 Answers

SOURCE: Looking for the torque specs for 1998 chevy astro van?

1998 chevy astro 4.3 v6 torque specs include :
* foot pounds *
balance shaft (if equiped) gear bolt = step 1 = 15 ft.lbs. step2 = additional 35 degrees.
camshaft sprocket bolt = 18 ft. lbs.
connecting rod cap = step 1 = 20 ft. lbs. step 2 = additional 70 degrees.
crankshaft damper bolt = 74 ft. lbs.
crankshaft oil deflectorbolt/nut = 27 ft.lbs.
cylinder head bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees. (tighten in sequence)
2811243.jpg


exhaust manifold bolts = step 1 = 11 ft. lbs. step 2 = 22 ft. lbs.
flywheel bolt = 74 ft. lbs.
main bearing cap bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees.
oil filter adapter bolt = 15 ft. lbs.
oil pan bolt/nut = 18 ft. lbs.
oil pump bolt = 66 ft. lbs.
rocker arm with press in studs = 18 ft. lbs.
rocker arm with screw in studs = 19 ft. lbs.
valve lifter retainer bolt = 12 ft. lbs.
water pump bolt = 33 ft. lbs.
* inch pounds *
balance shaft retaining plate bolt = 106 in. lbs.
camshaft retainer plate bolt = 106 in. lbs.
front cover bolt = 106 in. lbs.
intake manifold upper = step 1 = 44 in. lbs. step 2 = 88 in. lbs.
intake manifold lower = step 1 = 27 in. lbs. step 2 = 106 in. lbs. step 3 = 133 in. lbs. ** (tighten bolts in sequence)

cbb8861.jpg

thanks for your vote !

Posted on Dec 28, 2008

GM Elec
  • 1000 Answers

SOURCE: torque specs for 2000 chevy silverado truck 4.3 v-6 engine

Not sure what torque spec's your looking for.
Go to www.AutoZone.com, enter your vehicle information and check specifications. You should be able to look up the torque spec's your looking for.
Good luck.
Regards,

Posted on May 02, 2009

SOURCE: need torque specs for a 85 s10 chevy with a 2.5 engine?

here you go!

1dd4f4a.gif93a64e1.gif

Posted on Jun 21, 2009

  • 400 Answers

SOURCE: I am replacing the water pump on a 2000 Chevy

22ft lbs on the 6 pump to block bolts.

Posted on Dec 13, 2009

  • 56 Answers

SOURCE: torque specs needed

http://www.automotive.com/2002/101/chevrolet/suburban/1500-utility/37/specifications/index.html

Posted on Mar 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 chevy silverado water pump bolt torque specs


What size engine ? This vehicle could have six different engines .
Water Pump Replacement (4.8L, 5.3L, and 6.0L)
Install the water pump bolts.
Tighten
  1. Tighten the bolts a first pass to 15 N?·m (11 lb ft).
  2. Tighten the bolts a final pass to 30 N?·m (22 lb ft).
Water Pump Replacement (4.3L)
Tighten
Tighten the bolts to 45 N?·m (33 lb ft).

Jun 24, 2016 | Cars & Trucks

1 Answer

4610 ford diesel tractor water pump bolt torque settings


First you need to know the diameter of the bolts and the type of thread ie 3/8 N/C or 5/16 N/F then look at the type of bolt ie plain steel or high tensile SAE grade 3, 4, or 6, once you know this go to a general purpose bolt torque chart, and derive the torque spec info.
If the water pump is cast iron use the full torque specification.
If the water pump is alloy then reduce the torque spec 10%

Below is an example of a general purpose bolt / nut torque chart

26186159-4xbrgr0a3wt3vp4m2wlhd0as-1-0.jpg

May 05, 2016 | Ford Cars & Trucks

1 Answer

What are the torquing specs for a water pump on a 1992 Toyota pickup with a 22RE engine


the water pump bolts torque specs is T=1.85 kg-m (13 ft-lb). you must set your torque wrench nicely and carefully not to break the bolts then there you go.

Apr 03, 2016 | Toyota Cars & Trucks

1 Answer

Need torque specs. for water pump to 2004 chrysler pacific


I am certain I have the information you need. The problem is I am having trouble locating it in the FACTORY service manuals, terminology differs from what your searching for.

Torque for the Vibration Damper bolt is 115 Nm (85 ft.lbs.)

I am still trying to locate the pump torque.

Mar 28, 2013 | 2004 Chrysler Pacifica

1 Answer

What are the torqe specs for 2006 H3 fan/clutch and water pump


special tools you need EN 48543 FAN CLUTCH HOLDING TOOL. J41240 FAN CLUTCH REMOVER AND INSTALLER. TORQUE FOR FAN CLUTCH NUT 41 LB FT. FOUR BOLTS TO FAN BLADE TORQUE 20 LB FT.WATER PUMP BOLTS TORQUE TO 11 LB FT. DONT NEED SPECIAL TOOLS REMOVE WATER PUMP.

Nov 29, 2012 | 2006 Hummer H3

1 Answer

I need to know the correct torque specs for the 4 bolts that hold the a/c compressor on my 2003 Suzuki Aerio. In order to replace the water pump it was necessary to remove the compressor. The book supplied...


The ac compressor bracket bolts are to be torqued to 40 ft lbs, as far as the compressor itself you can just hand tighten bolts, there is no specs for compressor bolts just bracket, the bolts are just snug.

Aug 28, 2012 | Suzuki Aerio SX Cars & Trucks

1 Answer

I need torque specs to change a water pump for a 1999 chrysler cirrus 2.4 liter engine. water pump torque specs.


dont know the specs but you should be ok if you tighten the bolts snuggly and then 1/2 turn this will usually suffice just be careful not to over tighten

Nov 01, 2009 | 1999 Chrysler Cirrus

1 Answer

What are specs for water pump bolts for 2001


Home | Account | Contact ALLDATA | Log Out | Help ALL TUNE & LUBE DDG AUTOMOTIVE Select Vehicle | New TSBs | Technician's Reference Component Search: Conversion Calculator 2001 Ford Taurus V6-3.0L VIN 2 Flex Fuel Vehicle Level Specifications Mechanical Specifications Water Pump Water Pump Water Pump Notes Engine Front Cover and Water Pump Assembly 25 Nm (18 lb-ft) © 2009 ALLDATA LLC. All rights reserved. Terms of Use

Jun 10, 2009 | 2001 Ford Taurus

3 Answers

Replace water pump


First you must drain the coolant. Remove powersteering pump[keep hoses connected)this is just to make room for water pump removal so just sit it off to he side.Loosen the the water pump pulley mounting bolts, remove the drivebelt,remove the pump pulley. Remove the pump mounting bolts and pul the pump from engine.Install every thing in reverse ,but be sure to clean the mating surface of old sealer and gasket first, also be sure to use RTV gasket sealer on engine side of the new gasket.Be sure not to over/under tighten the bolts the torque specs. are 22 to 29 for the long bolts and 96 to132 for short bolts and 108 to 132 ft lb for the pulley bolts.

May 15, 2008 | 1994 Oldsmobile 88

Not finding what you are looking for?
1997 Chevrolet S-10 Pickup Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...