Question about Cars & Trucks

1 Answer

Not shifting fom 2nd to 3rd right some times from 1st to 2nd aswell either

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 32 Answers

Clutch and pressure plate my be bad or just pressure plate!

Posted on Nov 01, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: automatic transmission shifts hard and

have u checked the tranny fluid

Posted on Oct 06, 2008

alicantecoli
  • 22095 Answers

SOURCE: hard shift from 1st to 2nd gear automatic

what year is vehicle please ?? as people often put it in wrong catagory ,if its mazada 2007 then its dealer only as a computer controls it all and the software is factory encrypted to stop general garages from repairing it .But check for a vacumn pipe loose under bonnet ,thin rubber pìpe from inlet manifold to gearbor or a diaphram switch,

Posted on Feb 19, 2009

  • 1 Answer

SOURCE: It's an automatic but it won't shift from 2nd to 3rd.

I would have to say it is the tranny check the fluid make sure it is clean and at the correct level

Posted on Apr 16, 2009

emissionwiz
  • 74896 Answers

SOURCE: the engine rpms rev when shifting

Your trans is slipping, u are going to need to have it checked out at a trans shop, they will test drive it in most cases for free and report what they think is wrong or recommend more diagnostic work if they are unsure..

Posted on May 21, 2009

  • 51 Answers

SOURCE: transmission wont shitf from 2nd to 3rd

Is the transmission being controlled electronically or manually through a shift cable?

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota Yaris SR over reving when changing fom 1st to 2nd less from 2nd to 3rd.


Retrieve the engine and transmission fault codes, if any.There could be many reasons. But to start with, check the transmission oil level and catalytic converter.

Oct 05, 2012 | 2009 Toyota Yaris 1.3

2 Answers

02 Chevy avalanche 1500 need to know torque specs for intake manifold and if theres an tightening sequencing


the torque specs for your intake are the first pass to 44in/lb the second pass to 89in/lb. and the tightening sequence is as follows:
start on the passenger side (right side) the 3rd bolt (from front) is #1 then on the driver side (left side) 3rd bolt is #2 and 4th bolt is #3.Back to right side 2nd bolt is #4 and 4th bolt is #5. Left side 2nd bolt is #6 and 1st bolt is #7. Right side 5th bolt or rear most bolt is #8, left side rear bolt is #9. Then finish with right side 1st bolt is # 10.

Do that the first time at 44 in/lb then same thing over again at 89 in/lb

Nov 27, 2010 | Chevrolet 1500 Cars & Trucks

1 Answer

I have a Jeep Grand Cherokee 2001 with 88k on it . It feels as if it is holding on to 1st gear to long when shifting to 2nd and the same when shifting from 2nd to 3rd. The slam isnt as hard when going to...


as a quick remedy 1st check your fluid make sure is clean and leveled/adjust your kick down cable for early shifting by loosening the cable till you establish the right shifting

Jan 13, 2010 | 2001 Jeep Grand Cherokee

1 Answer

Does not shift from 1st to 2nd to 3rd...


It have valve bodies that control shifting. The only way to properly correct is to rebuid trans

Jan 06, 2010 | 1994 Ford Explorer Limited

1 Answer

Goes into neutral and then shifts hard into 1st on slowdown


It sounds like your input clutch seals are rolling. Is the check engine light on. It could also be the pressure control solenoid could be causing the problem aswell

Sep 02, 2009 | 1998 Buick Century

1 Answer

Transmission problem in E230 Benz


What you need to check is the transmission release bearing because if there is a clearance on the release bearing you will encounter this problem and also check the transmission oil.

Jun 08, 2009 | 1996 Mercedes-Benz E-Class

1 Answer

Transmisson problems


it can be the shift solenoid in the trans there is one for 1st and 2nd then there is one for 3rd and fourth easy to change drop pan they are right there.about 40 to 60 at dealer for solenoid and of course fluid and filter about 60.00

May 23, 2009 | 2005 Chevrolet Silverado 1500 2WD

1 Answer

Clutch


i had the same fualt and had to renew flywheel with clutchkit.hydraulic system had to be flushed aswell

Nov 26, 2008 | 2005 Mazda 3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...