Question about Buick LeSabre

1 Answer

Remove and install drivers outside door handle on a 1993 Toyota C

I have the inside door panel out now where di I go from here?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

With the window up you should be able to see the inside of the the handle and be able to reach it to remove the linkages and unbolt it.

Posted on Jan 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Want to replace broken outside door handle on 1993 corolla


  • remove screw on inner door release cover
  • pull latch out-slide and pull
  • remove inner linkage
  • remove window winder or switch
  • remove arm rest (2 screws)
  • undo screws and clips and remove trim
  • wind window up
  • from inside the door remove operating linkages-
  • two 10mm screws hold the outside handle
  • on some cars you might have to undo the latch to make room to undo the two screws for the handle
I know it is brief but it will give you an idea of what needs to be done .hope this helps.
should take 30mins

Sep 14, 2011 | 1993 Toyota Corolla

3 Answers

How do I replace the driver side outside door handle on my 1996 Toyota Tacoma?


Make sure window is up. Remove inner door panel. Disconnect latch mechanism. Should be a few nuts holding handle on. Unscrew them. Install front door outside handle frame sub-assembly. Using a torx wrench (Usually T30) install the outside handle.

May 04, 2011 | Toyota Tacoma Cars & Trucks

1 Answer

Replace outside door handle


you need to remove the inside door panel first. there will be a screw at the inside door handle and two screws for the armrest in the center of the panel. look around the outside edges of the panel for any other screws or clips to remove. the rest of the clips are behind the panel and snap when you pull on the panel. once off with the window up you can see the door handle screws. two of them. remove the connecting rods first.depending on which door you may have a lock rod also. then remove the screws and the handle will come out. good luck

May 22, 2010 | 1998 Toyota Corolla

1 Answer

Driver side door handle (outside) and gas pedal 2000 Camry


Bring the vehicle into the dealer if you have a sticky gas pedal. This is a TOYOTA PROBLEM.
Door handle:
It easy ! You need a philips2_bing.gif and flat screw driver,and a needle nose pliar.
Use flat screw driver and pry out the two or three dust covers for the arm rest screws then use philips and remove the screws. Next use the flat screw driver and pry out the black plastic mirror cover from the inside of the door. Pry out the switch with the flat screw driver and disconnect it. On the side of the door panel just above the striker/loch mechanism is this plastic push pull type of a hold in screw. Use flat screw driver to get it to move a little then pull it out with the needle nose. Depending on which door your doing if you have a map folder in the door there are two more screw to remove on the bottom of the door.
Now the inside door handle is tricky it comes out in TWO pieces. Use philips and get the only hold down screw you see out.( you may have to pry out a little screw cover first) Now the inside door handle cover is removed by placeing the flat screw driver on the rear of the outside of the cover top and on the outside rear bottom to release the tangs that are holding it onto the panel.Pry it out lightly you may have to place the screw driver over the top of the door release button and pry that way. Don't loose your cool its a pain but it will fall out. Once its removed unhook the panel.

Next lift the plastic cover and remove the door handle hooks and levers . Basically use common sense this is easy stuff. There may be two screws from inside of door panel that keep handle in place . Then work handle loose from outside and inside . reverse for installation.

Jan 27, 2010 | 2000 Toyota Camry

1 Answer

Need help on replacing door handle on toyota camry for the front driver side..


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If it's the inside handle, just disconnect the rod to the back of the handle to replace it. If it's the outside handle, pull back the weather seal and you'll be able to remove the bolts holding down the outer door handle

Sep 14, 2009 | 1995 Toyota Camry

1 Answer

Driver door handle of 2000 handle broken in half


FIRST YOU NEED TO REMOVE THE INSIDE PANEL. AFTER DOING THAT, WITH THE WINDOW ROLLED UP REMOVE 2 PLUGS ON THE METAL TO ACCESS THE TWO NUTS THAT HOLD ON THE OUTSIDE HANDLE. WHEN REMOVED, YOU CAN UNHOOK THE RODS THAT ACTUATE THE DOOR RELEASE. THE INSTALLATION IS THE REVERSE. I HOPE THIS HELPS. PLEASE FEEL FREE TO KEEP ME POSTED. THANKS FOR USING FIX-YA. ANY OTHER QUESTIONS, JUST ASK. GOOD LUCK

Sep 02, 2009 | 2002 Toyota Camry

1 Answer

How do I install a driver dide door handle on my


Inside handle, no, outside yes, to access nuts/bolts on back side.

Jul 31, 2009 | 1993 Jeep Wrangler

1 Answer

I want to replace the driver's side mirror and need to remove the inside door panel thanks


here is step by step instruction to remove your door panel. i am not sure if the picture are coming through so please forgive me on the images. please do not forget to rate and comment about your experience today wih fixya Front Door
  1. On vehicles without power windows, place a soft cloth under the window regulator handle and pull upwards on the cloth to release the snapring. Remove the regulator handle and plate.
89550p12.gif Using a taped prytool, carefully remove the bezel portion of the handle
89550p14.gif Remove the bezel by pulling towards the tip of the handle
89550p15.gif Remove any screw covers ...
89550p16.gif ... and extract any retaining screws from the door panel
  1. Remove the screw from the inside handle and slide the handle forward. Disconnect and remove the handle from the control link.
  2. On manual mirrors, remove the setting screw and knob. Tape the end of a thin flat-bladed tool and pry the retainer loose to remove the cover.
  3. If equipped with power windows, remove the power window switch from the and armrest.
  4. Remove the mounting screws and remove the armrest from the door panel. Remove the inside door handle bezel by pushing rearward.
89550p18.gif Carefully pry the edge of the door panel around the outer edges, then remove the door panel
89550p13.gif Once the door panel is removed, make sure to disconnect all wiring
  1. Remove the door courtesy light by pulling outward. Disconnect the electrical wiring.
  2. Remove the two screw caps and speaker cover(s). Remove six screws from the trim panel.
  3. Remove the door pocket from the panel.
  4. Tape the end of a thin bladed tool, then insert the tool between the door panel and door and pry the panel outward. Disconnect the electrical wiring after the panel is free and remove the panel from the vehicle.
To install:
  1. Connect the electrical wiring, if equipped, and install the trim panel onto the door.
  2. Secure the trim panel with the mounting screws, then install screw caps and speaker cover(s).
  3. Install the door pocket.
  4. Install the armrest and secure with the mounting screws. Install the power window switch as required.
  5. Install the door courtesy lamp. Install the inside handle bezel.
  6. Install the outside rear view mirror cover and retainer.
  7. Connect the inside handle to the control link. Install the handle, slide it rearward and install the screw.
  8. With the door window fully closed, install the window regulator and handle.

Apr 17, 2009 | 1993 Toyota Camry V6

1 Answer

Driver door handle will not open door 1993 Honda Civic


there is a pin in the door handle might have broke off there are two 10 mm nuts that will release the handle but you have to take the door panels off and remove it any local junk yard should have it or can order it for you

Mar 18, 2009 | 1993 Honda Civic 4 Door

1 Answer

Driver door opens from inside but not the outside


Usually have to remove inner door panel to get at it.

Mar 14, 2009 | 1994 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...