Question about Toyota Avensis

1 Answer

I cant get my hand in to take out the headlamp

Do i need to take the battery out in order to get the broken headlamp out?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 44 Answers

Sorry.... but yes

Posted on Nov 03, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlights will not come on 02 s10


Have you checked fuses ? The Instrument panel fuse block , Fuse Block - I/P
LH of the I/P, near the door jamb switch - LF , fuse # 7 HDLPSW 10amp.
In the underhood fuse / relay box - Headlamp power relay , RT HDLP fuse 15amp LTHDLP fuse 15amp.
Battery positive voltage to the headlamp switch is supplied by the HDLP SW fuse in the IP fuse block. When the headlamp switch is in the HDLP position, the headlamp power relay coil is energized. A voltage signal is also sent to the body control module (BCM) signaling that the headlamp switch is activated. The headlamp power relay coil is grounded at G102. When the headlamp power relay is energized, the relay supplies battery voltage to the LT HDLP and RT HDLP fuses. Both low beam headlamps are grounded by the multifunction headlamp dimmer switch in the low beam position through the normally closed headlamp grounding relay in the body relay block to G200.
High Beams-Except ZR2 Battery positive voltage to the headlamp switch is supplied by the HDLP SW fuse in the IP fuse block. When the headlamp switch is in the HDLP position, the headlamp power relay coil is energized. A voltage signal is also sent to the body control module (BCM) signaling that the headlamp switch is activated. When the headlamp switch is in the AUTO or PARK position and the ambient light sensor detects darkness, the BCM produces a voltage signal that will also energize the headlamp power relay. The headlamp power relay coil is grounded at G102. When the headlamp power relay is energized, the relay supplies battery voltage to the LT HDLP and RT HDLP fuses. The RH high beam headlamp receives current directly from the RT HDLP fuse. When the headlamp switch is in the HDLP position, the BCM removes the ground path to the headlamp grounding and DRL relay coils. This allows current to flow to the LH high beam headlamp through the normally closed contacts of the DRL relay. Both high beam headlamps are grounded by the multifunction headlamp dimmer switch in the high beam position through the normally closed contacts in the headlamp grounding relay to G200. A ground signal is also sent to the BCM in order to confirm high beam operation.

In the i

Mar 01, 2015 | Cars & Trucks

1 Answer

Need to change out 2003 headlamp assembly on Chevy Impala


your owner manual in the glovecompartment will show you how to replace headlamp bulb,the auto parts stores sales person will help you, i have seen them help people remove replace car batteries,and wiper blades,they will help you replace headlight if you buy headlight bulb at their store,if you do it your self.be sure to wear clean gloves on your hands. your fingers and hands is not suppose to touch the headlight bulbs because halogen bulbs will blow out if oils on your fingers and hands touch the halogen bulb.

Aug 30, 2012 | 2001 Dodge Dakota

1 Answer

How to change a n/s headlamp bulb fiat stilo


download.fiat-bg.org/Books/Stilo/Stilo_Changing_Headlight_Bulbs_without_removing_bumper.pdf

Jan 24, 2012 | Cars & Trucks

1 Answer

Headlights removal ford explorer 96


  1. Check that headlamp switch (11654) is in the off position.
  2. Lift hood (16612).
  3. Release latch and swing filler panel to left or right.
  4. Remove electrical connector from headlamp bulb by grasping wires firmly and snapping connector rearward.
  5. Remove headlamp bulb retainer (13N019) by rotating counterclockwise (when viewed from rear) about one-eighth turn and sliding ring off plastic base. Keep headlamp bulb retainer as it may be used again to retain new headlamp bulb.
  6. Carefully remove headlamp bulb from socket by gently pulling straight backward out of socket. Do not rotate headlamp bulb during removal. 7056091.gif
Headlamp Assembly, Explorer
Removal and Installation
  1. Disconnect battery negative cable.
  2. Remove blind rivets (2) attaching screws (4) and radiator upper sight shield.
  3. Remove turn/park lamp attaching screws (2) and pull assembly away from body. Remove bulb sockets from housing and remove lamp assembly. Repeat on opposite side of vehicle.
  4. With turn/park lamp assembly removed, screw attaching grille to front fender flange is accessible. Remove grille attaching screw. Repeat on opposite side of vehicle.
  5. Remove attaching screws (4) located across top of grille.
  6. Grip lower edge of grille and pull outward to disengage from retaining clips. Remove grille.
  7. Using needle-nose pliers, compress barbs on headlamp housing retainer. With barbs compressed, pull forward on housing just enough to disengage from retainer. Repeat on opposite side of headlamp housing.
  8. Turn headlamp housing as necessary and pull forward to disengage from headlamp aiming ball socket.
  9. Disconnect wiring from headlamp bulb socket.
  10. If replacing headlamp housing, remove retaining collar and bulb.
For installation, follow removal procedures in reverse order. Make sure to check headlamp aim. 568a220.gif

Apr 02, 2010 | 1996 Ford Explorer

1 Answer

My headlights dont work,.all other lights are fine though,.is it the fuses or the bulbs? im not sure what fuses they would be,.there seem to be different ones for the same thing


do your flash to pass lamps light when you pull the stalk towards you? If yes, the bulbs are ok.
Do the hig beams work?
Your headlamps have sepaerate fuses for each headlamp and you have a low beam relay and a high beam relay under the hood in the black box.
If everything is out, I suspect a bad headlamp switch.
Check car-part.com and look on page with * for cheapest price.

Your owner manual will identify fuses & relays.

PS, You did not recently instal high current bulbs did you? If yes, put originals back in.

HEADLAMPS

The voltage is supplied to the lamp switch through a fuse. This fuse is located in the central junction box in the left-hand footwell.
When the headlamps are switched on, a voltage is supplied to the high beam/low beam switch and to the low beam relay. The relay for the low beam is located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "low beam", then a voltage is supplied through the low beam relay to the low beam part of the headlamp assembly. The left and right-hand low beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "high beam", then a voltage is supplied through the high beam relay to the high beam part of the headlamp assembly. The left and right-hand high beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.

----------------------------------------------------------------------------------------------------------
Lamp Switch
Removal
  1. s2y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
    Remove the lower driver's side footwell trim.
  1. Detach the lamp switch bezel.
    • Remove two screws.
  1. Remove the light switch.
    • Remove three screws.
    • Disconnect the electrical connector

Feb 23, 2009 | 2005 Ford Focus

1 Answer

How head litht assembly come out


  1. Open the hood.
    1. Remove the thumb screws (4) that retain the headlamp (3) to the headlamp bracket (1).
    2. Pull the headlamp (3) forward in order to disengage the rear retaining pin (2).
    3. Remove the headlamp (1) from the vehicle.
    4. Disconnect the electrical connectors. NOTE: Avoid touching the bulb or letting the bulb come in contact with anything damp. Oil from your skin or moisture on the bulb can cause the bulb to explode when the bulb is turned on. If either comes in contact with the bulb, clean the bulb with alcohol or a suitable degreaser and wipe the bulb dry.
    5. Turn the headlamp bulbs (2, 3, 4) counterclockwise in order to remove the bulbs
      1. Turn the headlamp bulbs (2, 3, 4) clockwise in order to install the bulbs.
      2. Connect the electrical connectors.
      3. Install the headlamp (1) to the vehicle.
  1. Press the headlamp (3) rearward in order to engage the rear retaining pin (2).
  2. Install the thumb screws (4) in order to retain the headlamp (3) to the headlamp bracket (1).
  3. Aim headlamp. Refer to Headlamp Aiming.
  4. Close the hood.
  5. IF YOU NEED PICTURES I MUST EMAIL THEM TO YOU THEY ARE TOO LARGE OF WRONG FORMAT TO SEND VIA FixYA's WAY Let me Know Your Email Address if you need Pictures

Jan 26, 2009 | 2003 Buick Park Avenue

1 Answer

Dim headlight on 92 town car


make sure the terminals are clean at the headlamps. check the black wire to ground for open circuit. an open ground will cause a dim headlamp if there is no way to test wire jump the black wire to ground and see if lamp brightens

Dec 28, 2008 | 1992 Lincoln Town Car

1 Answer

Headlamp assembly


Remove the 3 10mm bolts from the top outer edges of the assembly. Then slip your fingers under the front edge and pull up while pulling to the front of the car to remove it from the plastic retainer under the assembly. Reinstall in reverse order.

Nov 18, 2008 | 2001 Mitsubishi Eclipse

2 Answers

2002 trailblazer


All you have to do is find the "round rubber cover" on the back of the headlamp, pry it out with a flathead screwdriver and the lamp is right there.
To remove the headlamp assembly on a Trailblazer, remove the plastic panel that covers the hood latch assembly.
Take the cover for the air filter in order to get to the low beam cover.
Take the 3 screws out of the air filter cover and remove. You will then be able to get to the back of the low beam lamp. The high beam is reachable without this hassle.


Oct 07, 2008 | 2002 Chevrolet TrailBlazer

1 Answer

How to install 2003 dodge neon headlight assembly.


  1. Disconnect and isolate the battery negative cable.
  2. Remove screws attaching headlamp module to upper crossmember.
  3. Remove headlamp module from vehicle.
  4. Disconnect wire connectors from back of headlamp module.
  5. Remove headlamp module

Jul 02, 2008 | 2003 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...