Question about 1995 Mercury Villager

1 Answer

How do you remove the door panels on a 1995 mercury villager

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

Http://autos.groups.yahoo.com/group/villagerquest/

you have to remove the cup behind the door handle. rmove screws aroun the door pull. get a screw driver and pry the trim panel away from the door carefully. There is a plastic christmas tree clip every 6 inches. when the bottom & sides are free, lift up the trim panel to get it out of the track at the base of the window.
--------------------------------------------------------------------------------------

Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).

  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connections.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  1. Remove the front door trim panel.

Posted on Jan 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver side door rod to handle has come loose from the locking mechanism


There is a replacement clip available in most auto repair stores. HELP brand. Must remove the door panel (inside) and re-attach.

Feb 16, 2014 | 1995 Mercury Villager

1 Answer

I can't open the back door on my mercury villager 1995


pull off the trim panel on the lifgate for access. look in files at this site and photos. I have a latch in the files.

http://groups.yahoo.com/group/villagerquest/

Nov 04, 2010 | 1993 Mercury Villager

1 Answer

Where is the turn signal relay located in a 1995 mercury villager?


http://groups.yahoo.com/group/villagerquest/

behind dirver side kick panel. remove bracket with 2 10mm bolts on it. has 3 relays on it. Lucas relay

Sep 23, 2010 | 1995 Mercury Villager

1 Answer

Need a diagram for installing a drivers side electric power mirror on a 1995 mercury villager van


here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal
  1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).




  1. Remove the wire clip.
  1. Disconnect the power outside rear view mirror electrical connector.




  1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.




Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal
  1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws.


    Remove the outside rear view mirror mounting hole cover.
Installation
To install, reverse the removal procedure. Mirror Control
Removal
  1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).


May 13, 2010 | 1995 Mercury Villager

1 Answer

Handle broke off sliding door on drivers side 2000 mercury villag


Trim Panel —Sliding Door
Special Tool(s) syv~us~en~file=st1181a.gif~gen~ref.gif Safety Belt Bolt Bit (Used for T-50 Head Bolt)
501-010 (T77L-2100-A) Removal
  1. Remove the sliding door trim panel finish panel.
94d5982.gif
  1. Remove the sliding door trim panel.

Apr 13, 2009 | 2000 Mercury Villager

1 Answer

Doors locks


go here and read files on this issue and how to fix it,

http://autos.groups.yahoo.com/group/villagerquest/

Apr 03, 2009 | 1995 Mercury Villager

1 Answer

Location of computor on 1995 merc villager


behind glove box

They seldom go bad so don't change until you know for sure. What are symptoms?

for villager/quest help go here

http://autos.groups.yahoo.com/group/villagerquest/
Powertrain Control Module (PCM) stv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. Refer to Module Servicing Precautions in Section 18-01 .
Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the four console compartment plastic screws or C/D changer cover plastic screws (if equipped) and the console compartment door (045G36) or C/D changer cover.
  1. Remove the plastic screw, two lower screws, two center bolts, two upper screws and the screw at the instrument panel bracket, then separate the glove compartment from the instrument panel (04320). Disconnect the glove compartment striker plate catch electrical connector.
  2. Remove the two passenger side air bag module bracket nuts, the passenger side air bag module bracket bolt and the passenger side air bag module bracket.

  1. Remove the powertrain control module (PCM) electrical connector bolt. Pull the connector from the PCM and position aside.




    Remove the two PCM bolts.

    ec13884.gif

  2. Remove the PCM relay.

  3. Remove the three electrical connectors attached to the PCM.
  4. Remove the PCM from the instrument panel.

Mar 14, 2009 | 1995 Mercury Villager

1 Answer

Removing the door panels


there is mounting screw on the panel you have to take the screw off the panel using screw driver. If you can see the screw on the panel it's because the screw is inside the hole on the panel it cover with small plastic knob remove that so you can see the screw.

Jan 04, 2009 | 1995 Mercury Villager

Not finding what you are looking for?
1995 Mercury Villager Logo

Related Topics:

460 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...