Question about 2001 Ford Escape

1 Answer

B1352 starts and dies

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 75,797 Answers

The following are the general instructions on the start of diagnosing any electronically controlled engine or transmission problem.

The engine and the automatic transmission (transmission control is only for automatics, engine is still computer controlled no matter the transmission type) in this vehicle are computer controlled and in most cases when a fault occurs a fault code is stored in the memory of the computer control module. There are exception to this, such as the Mass Airflow Meter and fuel pressure problems. What must be done is to have all the basic testing done such as a scan of the system for fault codes as well as a check with a live data scanner tool for engine functions that are not within range of normal, a trained technician is required to know what is correct and what isn't, then based on careful diagnostics done from a factory repair manual the correct part is replaced or the wiring repaired or the computer replaced (known as the PCM or ECM,ECU), which is very rarely the problem. Other basic checks must be done as well such as mechanical problems with the engine as well as engine state of tune and mileage on the engine. The transmission can have mechanical issues as well such as no gear engagement at all or a failed pump or other pressure related problems. Also engine mechanical problems can and do cause many drive-ability related problem such as rough idle and other symptoms.

Posted on Nov 01, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is chime module located on 2005 ford taurus


There is no chime module ,there is a speaker inside the instrument cluster.
Door Ajar Chime
The door ajar chime feature is controlled by the smart junction box (SJB). The driver and passenger door ajar switches, and the liftgate are hardwired to the SJB. If any door or liftgate is sensed as being open, and the ignition switch is in RUN/START position, the SJB will process the input and sends a chime request to the instrument cluster over the controller area network (CAN).
Safety Belt Warning Chime
The safety belt chime feature is controlled by the restraints control module (RCM). The driver safety belt switch is hardwired to the RCM. The RCM communicates with the instrument cluster over a hardwire connection. If at any time during the first 6 seconds after the ignition switch is placed in RUN the driver safety belt is sensed as being unfastened, the RCM will process the input, and in turn, sends a chime request to the instrument cluster.
Have the vehicle checked for DTC'S - diagnostic trouble codes ,not OBD 2 codes , the check engine light has nothing to do with this .
Instrument Cluster Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 Instrument Cluster is Defective Instrument Cluster INSTALL a new instrument cluster. REFER to Section 413-01 . B1352 Ignition Key-In Circuit Failure Instrument Cluster Go To Pinpoint Test B . B2477 Module Configuration Failure Instrument Cluster REFER to Section 413-01 .
For a complete list of instrument cluster DTCs, refer to Section 419-10 .


Smart Junction Box (SJB) Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 SJB is Defective SJB INSTALL a new SJB. REFER to Section 419-10 . B1352 Ignition Key-In Circuit Failure SJB Go To Pinpoint Test B . B1577 Lamp Park Input Circuit Short to Battery SJB Go To Pinpoint Test E . C1167 Park Brake Actuator Assembly Switch Released Circuit Short to Ground SJB Go To Pinpoint Test F . Your best bet is to have a qualified repair shop diagnose this problem ,what ever it is .
Have the vehicle

May 28, 2016 | Ford Cars & Trucks

1 Answer

Truck runs fine then dies while driving then will start back up and run ok.


About 56,700 results (0.76 seconds) Search Results

    GMC Sierra 1500 Questions - Truck suddenly stops running ...

    www.cargurus.com > Questions > GMC > Sierra 1500

    CarGurusJul 11, 2013 - Truck suddenly stops running, acting like it's out of fuel. ... start it and let it run until it dies then check the pressure and shut the key off. ... Was running fine and then turned off as if the ignition was turned of. .... Well mine was a loose battery connection that just shut down the vehicle completely while driving.

    1998 1500 5.2 Shuts Off Randomly - CarGurus

    www.cargurus.com > Questions > Dodge > Ram 1500

    CarGurusAug 29, 2011 - I let it sit for a second then tried to start it back up and it wouldn't start.... 2006 ram 1500 randomly dies while driving 13 answers ... truck started outrunning fine but would randomly die. wait a few ... Used GMC Sierra 1500".

    GMC Sierra 1500 Questions - started stalling and dying ...

    www.cargurus.com > Questions > GMC > Sierra 1500

    CarGurusJul 28, 2008 - The truck starts and dies. Have to give a little gas to keep running.While driving have to 2 foot it so it won't die. Wants to die when I come to a ...

    Engine Dies and Then Starts Right Back Up

    www.justautorepair.com/chevrolet/blazer/stalls-starts-up

Feb 04, 2016 | 1997 GMC Sierra

3 Answers

No give fire heve new coil and fuel pump


This code is for ABS and will have nothing to do with a no start condition. What size motor is in the vehicle? I need to know in order to offer assistance

Jul 14, 2015 | 2002 Mercury Cougar

1 Answer

Ranger won't crank.


accessory relay delay Coil Circuit Failure.There is a delay relay that is under the dash in the fuse panel.

Dec 03, 2013 | 1998 Ford Ranger SuperCab

1 Answer

B1352


Here's a link to your code.

Mar 11, 2013 | 1997 Lincoln Town Car

2 Answers

Cyliner 1 misfire, codespo301, po316, po301b, b1352


A misfire can be cause by several factors. here are a list of things to check check spark plug on that cylinder and check coil and wiring for coil. check cylinder compression on all cylinders if one cylinder is less than 10 psi different from the others that can cause a miss, last but not least check injector pulse using a noid light for injector pulse if pulse is good then injector is bad replace and that should solve your problem. Good luck and contact if you need more help. Thanks for using FIX YA

May 12, 2009 | 2006 Ford Taurus

1 Answer

1989 Bronco starts but dies after a couple of seconds


try checking the thermostat control senser. it caused my bronco to start for a second and then die. after a while it would finally start and run for a while then die driving down the road. i changed the thermostat control senser and it fixed all problems of dieing

Apr 27, 2009 | 1989 Ford Bronco II

Not finding what you are looking for?
2001 Ford Escape Logo

626 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...