Question about Cars & Trucks

1 Answer

How do i find out what number blue marlin i have out of the 500 made, as the blue marlin logo that was on the over head panel light is missing

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,132 Answers

You may have this posted in the wrong product category. Please select another category appropriate to the problem and re-post the problem so the correct expert will see and respond to the question..
This is for car and truck problems related to Factory Installed Systems not add on aftermarket systems.
This post can't be removed or moved, please re-post the question in the correct product category. Thanks

Posted on Nov 01, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am having a misfire on cylinder 2 but not sure how, I replaced the head, the plug, the wires and the coil pack....what am I missing. No pun intended.


Run tests to see why missing: spark test on no. 2, need a good blue spark to rule out ignition problem. Gas test: make sure injector for #2 is pulsing-is gas getting into the cylinder? Pull the plug after cranking a few seconds and see if wet with gas, or check for a pulsing signal on the injector. A "noid" light can be purchased cheap, it plugs into injector connector and blinks if wiring is working right.
If still no help, you need a compression test to check compression on #2. Low compression may indicate a head gasket failure or valves not sealing properly.

Jun 28, 2013 | Cars & Trucks

1 Answer

Chevy malibu 2001 code po300


P0300 is multiple cylinder misfire, meaning a engine miss is detected on more then 1 cylinder, I would have the codes scanned at auto part store to know for sure which cylinders are actually missing, if there are 2 cylinders that are missing and they are side by side, such as cyl. 1,3. Or 3,5. If so its possible u have a blown head gasket blowing in between the 2 cylinders.. 1st double check that your wires are installed correctly, the coil packs have numbers on them to assure proper location.. Note the rear head has cylinder 1 3 and 5. Some people get that confused.. Providing you have a 3.3, 3.8 or 3.1 liter engine.

Jun 10, 2012 | Chevrolet Malibu Cars & Trucks

1 Answer

I have 1994 grand cherokee Jeep, Jeep heats up and will not start the temp gage is not working; i have replaced the thermo sts sensor and gasket. The temp gage on panel still doesnt work... My Jeep also...


white /light blue smoke is a sign of a blown head gasket or intake gasket when you changed the oil filter was it creamy cause if it was then is a head gasket

Apr 08, 2011 | 1994 Jeep Grand Cherokee

2 Answers

2004 Jeep Grand Cherokee (63,000 mi - V8) Check engine light indicates #1 cylinder misfiring. Spent $$ getting system flushed for carbon residue. Drove 3 weeks, started up, ran rough, and light came on...


The miss,does not just come and go,if it is a engine valve,replace the coil and boot,go from there,if this does not solve the problem,then the injector is gone out,or going out.If it is a engine valve,the miss would never get better,then worse,it would be the same all the time,get him to run a air compression test,get the valves up(close)and see if any air is detected threw the exhaust,or the intake,it will be present if the valve is the problem.

Apr 24, 2010 | 2004 Jeep Grand Cherokee

2 Answers

1995 ford tarus no panel lights or parklight nor brake lights at night time


the head lamp switch is faulty and replaced and that should correct the problem

Mar 16, 2010 | 1998 Chevrolet S-10 Pickup

3 Answers

Brake lights not working even though the brake peddle is pushed down The switch still goes in and out. Fuse box has some fuses missing. The fuse box does not have a desription on every plug of what it is...


Here are the numbers on your fuseblock and fuses coresponding to the number that is on your fuse block.
1-20 amp (yellow)
Hazard flasher
2-10 amp (red)
back up lights, A/C clutch cycling Switch
3-30 amp (green)
Power windows
4-30 amp (yellow)
A/C or heater blower motor
5-20 amp (yellow)
Panel Lights, Side marker lights, Park, Taillights, Clock & radio display Intensity, License & panel lights.
#6-10 amp (red)
Stoplight, buzzers, Anti-lock brake module
#7-15 amp (lt. Blue)
Tachometer, horn & Relay
#8-8 amp (yellow)
Power Door locks
#9-10 amp (red)
Radio
#10-10 amp (red)
Rear Wheel Anti-lock module, Turn Signals
#11-20 amp (Yellow)
Windshield wiper & washers
#12-15 amp ( LT. Blue)
Cigarette Lighter
#13-5 amp (tan)
Speed Control, warning buzzers, gauges, indicator lights
#14-5 amp (tan)
Time/delay relay & under-hood light, dome light, power mirrors, readio & clock Memory, Interior lights, reading lights
#15-blank
Not used
#16-4 amp (pink)
Radio Lights & overdrive switch light 1989-91, Cluster lights, Cigarette Lighter light & as tray light, Cluster lights, A/C & heater controls.
#17-relay
Hazard Flasher warning
#18-relay
Relay
#19-Circuit breaker
#20-relay
Turn signal Flasher
#21-buzzer
Warning
#22-Relay
Horn

Aug 04, 2009 | 1991 Dodge Dakota

1 Answer

Service light has come on. Engine idles at 3000 RPM at one time then at 500 RPM at another. When at 500 RPM sounds like it is missing and sometimes stalls.


Idle control sensor on thr trottlebody or if eequipped; airflow meter ...off the top of my head, hope it helps.

Jun 20, 2009 | 1999 Mercury Sable

1 Answer

'86 Mustang Head Light Switch Pin Out Connectors?


I can give you 94 mustang. Don't have 86 but maybe similar

7fc8945.gif Pin Number Circuit Circuit Function B1 38 (BK/O) Power Supply to Battery B2 195 (T/W) Tail Lamp Switch Feed I 19 (LB/R) Instrument Panel Lamp Feed IGN — Not Used R 14 (BR) Headlamp Switch to Tail Lamp and Side Marker Lamps H 15 (R/Y) Headlamp Dimmer Switch Feed DN — Not Used D1 54 (LG/Y) Interior Lamp Switch Feed D2 706 (GY) Battery Saver Door Switch Feed

Apr 30, 2009 | 1986 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...