Question about Ford Cars & Trucks

1 Answer

Crane hi-6 box - Ford Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 75,840 Answers

You may have this posted in the wrong product category. Please select another category appropriate to the problem and re-post the problem so the correct expert will see and respond to the question..
This is for car and truck problems related to Factory Installed Systems not add on aftermarket systems.
This post can't be removed or moved, please re-post the question in the correct product category. Thanks

Posted on Nov 01, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a workshop manual with a detailed layout of the front end in a 1985 TG400E Tadano crane.


the crane manufacturer will use generic components where ever possible
as the crane is a specialist piece of equipment it will require approved parts to keep it certifiable
take it to a crane repair facility and have it done properly

Oct 14, 2016 | Cars & Trucks

2 Answers

We have a plating certificate for Iveco for Gross weight 26000 with different weights on each Axle. It has a crane. How do we work out how much load can be on?


it works out as 10 ton , 10 ton and 6 ton on the front axle
there may be variations between state regulations so best talk with the relevant authority
Bill of material that was used by the manufacturer to make the vehicle will have the load ratings for each axle so talk with customer relation s direct by phone to get a copy of that engineering specification

Apr 21, 2016 | Cars & Trucks

1 Answer

2001 olds aurora 3.5l engine removal


Remove the bonnet, drain oil and water remove radiator and fan remove all hoses cables and wiring attached to the engine. take weight of engine with a floor crane support the transmission .uncouple transmission from engine remove engine mount bolts , take a little more weight with the crane and slide engine clear of transmission , lift clear of car and slide crane clear to engine stand.

Dec 25, 2014 | 2001 Oldsmobile Aurora

1 Answer

I have a grove at 422 crane with a clark 24000 hr 6 transmission. Having a problem with it coming out of 6th gear but converter staying locked. Anyone have this problem?


you may consider that the rear bearings of the box are faulty allowing the output shaft to move slightly out of alignment and allowing the gear to work out of engagement. Check the magnet on the drain plug for metal bits.

Dec 22, 2014 | Cars & Trucks

1 Answer

Crane HI-4 ignition how to test the single fire coil and module


Hi Anonymous, for more information about your question please visit the websites below. Good luck and have nice day.
http://www.nightrider.com/biketech/download/crane/install_hi4_race2.pdf

Apr 16, 2013 | Cars & Trucks

2 Answers

I need to know how to replace a clutch on a 1989 4 runner toyota pickup 6 cylinder engine


2Ways 1 take the Engine out and fit the new clutch if you have a block and tackel or crane to lift it.
2nd Jack up truck as high as possible and fit stands under,, Rmove gear levers/tail shafts/ transfer box and all other parts before removeing X member on box/ and put jack under engine/before removing all bell housing bolts and starter motor..remove box assy.. fit new clutch, refit box etc in reverse of removal.. But engine out is the BEST WAY

Oct 02, 2009 | 1989 Toyota Pickup SR5

2 Answers

Crane Hi-6 ignition.....car quits going down the road. Sometimes it starts right back up, sometimes in 5 minutes or so. I noticed when it dies that the led is out on the ignition box. Could the box heat...


Check power SUPPLY to the ignition box when the problem is happening.If supply and ground are maintained at all times,then yes,it is the ignition box.I have an MSD 6AL i bought NEW about 5 years ago...it just quit working one day.MSD said they would fix it if i shipped it to them for a min/max charge.Min like $80.....max was $150.I bought an electronic distributor,module,and wiring harness from Mopar Performance for $200 brand new.

Sep 09, 2008 | Ford Mustang Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75824 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...