Question about Honda Cars & Trucks

Open Question

HOW DO YOU REPLACE A 2002 HONDA ACCORD CRANKSHAFT SEAL

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

duane_wong
  • 6826 Answers

SOURCE: how to replace Honda front Crankshaft Seal

Have to take off the crankshaft pulley to get at the Crankshaft Seal.

Use a hooked seal remover to dig in and pull the seal out without damaging sealing surfaces.

Posted on Jul 21, 2010

  • 878 Answers

SOURCE: How do I change the

jack car up set on stands ,remove passenger side wheel,remove plastic cover on fender ,i believe is a 36mm socket to loosen nut on harmonica balencer,once you remove nut and washer the seal is there ,tap out with screw driver good luck

Posted on Apr 01, 2011

  • 5 Answers

SOURCE: 1989 honda accord oil leeak cam/crankshaft

Camshaft seal must be replaced when the engine is cold. Take off valve cover and then the upper timing cover and take off the camshaft sprocket and the timing belt will come off too. Use a small screw driver to pull the old seal off and then force in the new one. Then pull back the sprocket and timing belt. If the engine is hot, the timing belt will not go back on the sprocket until the engine is totally cool down overnight. Or if you want, you can set the camshaft to TDC and take off the rocker arm assembly, take off the seal and put the new one on and reinstalled the bolts to the rocker arm assembly and then do the valve adjustment. From Sometime mechanic.

Posted on Nov 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Po1362 and po1359 on 2002 honda accord se 2.3 engine


Hi brian.
I think you mean P1362 and P1359
both fault codes are pointing to the crankshaft sensor.
check the wires/ connector. replace the crankshaft sensor.
Good luck

Apr 26, 2015 | 2002 Honda Accord

1 Answer

Ow to replace crank shaft seal


is it the front crankshaft seal or the rear the front you can do by removing the lower balancer replacing the seal the rear you have to pull the transmissionand flywheel to get to that seal but the one piece you may have to remove part of the oil pan

Dec 13, 2014 | 2003 Honda Accord

1 Answer

How to replace Crank Seal , Honda Accord 95, F22B2 engine


this is covered in the FSM. 95 accord.
did you google this?
http://www.honda-acura.net/forums/accord/137349-1993-f22-crank-cam-balance-shaft-seal-hell.html

are you sure its only the crank seal,????
gravity lies. as does windage effects.
is this an A/T or M/T car, the latter makes the bolt come off easy
(5th gear + brakes) the slush pump tranny NOT.
so if you read the FSM it states." it shows photo of tire off and pulley bolt view and how the body ends just above that bolt, (see it?)
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belts.
  3. If necessary, secure the crankshaft with a flywheel holding tool.
For some engines, a special pulley holder tool is available to secure the pulley while removing and installing the bolt (refer to the illustration)."
4 Remove the crankshaft pulley bolt. This bolt can be difficult to remove. Spray the bolt with penetrating oil and allow it to soak overnight. Book forgets to see CCW direction on bolt (RHT)
the bolt will take about 200fl/lbs of reverse torque to get off.
5 Carefully remove the pulley from the crankshaft. Do not pry it off.
6:
Remove the key from the crankshaft sprocket. Be sure not to lose it.
7 -If necessary, remove the tool holding the crankshaft.

remove seal with seal puller or screw trick ,etc.
do not damage the seal base collar of the housing. DO NOT.

is this your first engine seal work>?
or done many , just need help with one honda.?
if doing all work on a honda, did you ever consider a real FSM?
why not get one, and read it, and all the steps and warnings.
worst case.
if you work engines, you know as you go , you see
Omg, it not the crank it the cam leaking, or just a bad valve cover.
fate happens, distributor seal leak too.

with all FWD, doing a crank seal can be easy or hard.
no access panels in finder
or on some cars, 7ton pressed on pulley, (Dodge neons/ yuk)

bolt spec:
1994-95 Accord and Prelude-181 ft. lbs. (245 Nm)

if the 90,000 mile timing belt is ignored, you will bend the head valves over, or worse... so...... all this , is a consideration.

Feb 25, 2014 | 1995 Honda Accord

1 Answer

How do I change the crankshaft seal on a 1993 Honda Accord LX?


jack car up set on stands ,remove passenger side wheel,remove plastic cover on fender ,i believe is a 36mm socket to loosen nut on harmonica balencer,once you remove nut and washer the seal is there ,tap out with screw driver good luck

Mar 20, 2011 | 1995 Honda Accord

2 Answers

How hard is it change front and rear oil seals?


By front and rear oil seals, I am assuming that you are refering to the CRANKSHAFT front and rear oil seals.
The front crankshaft oil seal is under all the components that must be removed to replace the timing belt.
The standard labor time to replace this seal is 4.0 hours for the 4 cylinder and 4.8 hours for the V-6.

The rear crankshaft oil seal requires removal of the transaxle to replace it.
The standard labor time required to do this is 7.3 hours

This is not a job for a novice unless you want to purchace a service manual and spend a lot of time reading the instructions before jumping into it.

Dec 01, 2010 | 1995 Honda Accord

1 Answer

How do you lock your balance shaft or crankshaft on a 92 accord to replace seals


use an old timing belt and wrap it around the pulley. use a pair of vice grips to bind the ends of the timing belt around the pulley, then hold on and unbolt.

Nov 10, 2010 | 1992 Honda Accord

1 Answer

How to replace Honda front Crankshaft Seal


Have to take off the crankshaft pulley to get at the Crankshaft Seal.

Use a hooked seal remover to dig in and pull the seal out without damaging sealing surfaces.

Jul 20, 2010 | 1995 Honda Accord

1 Answer

Leaking oil, when I have timing belt cover off can


That's one of the main seals , needs replacing

Oct 12, 2009 | 1999 Honda Accord

2 Answers

1989 honda accord oil leeak cam/crankshaft


Take valve cover gasket bolt out replace... An when you do the lower crank seal you have to take off oil pan.. Big job but it can be done..

Jun 27, 2009 | 1989 Honda Civic

1 Answer

Honda accord lxi 89


yes it is most likely the crankshaft seal or the camshaft seal the only way to make sure is to pull timing cover using 10 mmm sockets and youll have to remove belts and pulleys using 12mm and 14mm sockets and wrenches and pulley puller also it is not easy but you need to be sure and to replace the seals youll need to remove those anyways. Purchase a repair manual to assist you in this job at local parts store haynes or chiltons will do about $20.00 or so.

Feb 17, 2009 | 1998 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...