Question about Nissan Cars & Trucks

Open Question

How do you replace a knock sensor on 2001 nissan frontier

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 341 Answers

SOURCE: location of knock sensor

Knock sensors can be difficult to locate because there usually buried under intake or exhaust manifolds and misc. engine wiring and plumbing. Knock sensors need to hear an engine knocking noise, therefore there usually located somewhere they can hear an engine knock. If it's a V6 then possibly it will be between the cylinder heads and access to them can only be attained by removing the intake manifold. I would suggest calling a Nissan Dealer parts person and ask them. Good luck.

Posted on Jun 16, 2009

Ad
  • 1986 Answers

SOURCE: adjusting 2001 nissan frontier headlights

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

If you have one adjustment screw, it will control your vertical aim. If you have two adjustment screws, one will control your vertical aim and the other will control your horizontal aim

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 30, 2009

lindsay836
  • 677 Answers

SOURCE: engine code p0340. replaced distributor

The engine code you have given is a p0340, which is a cam sensor.
Why did you replace the distributor ?
Please let me know.

Posted on Feb 06, 2010

ZJLimited
  • 17970 Answers

SOURCE: Diagram available for 01 Nissan Xterra Knock Sensor location?

V6 3.3L The sensor is located underneath the air intake manifold on top of the engine block. This should take an experienced mechanic about 3-4 hours to replace.

9bd8ec7.jpg

Fig. Engine compartment component locations

Hope this help (remember rated this free help) Good luck.

Posted on Feb 08, 2010

cris_p
  • 62 Answers

SOURCE: how to replace knock sensor in 1995 nissan altima

remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where I can locate po325 knock sensor for nissan frontier 2000


underneath intake manifold between cylinder 1 and 2.

Mar 09, 2015 | 2000 Nissan Frontier

1 Answer

How do I bypass a knock sensor on a 2000 Nissan frontier


Bypassing (hotwiring) the knock sensor will remove a signal the computer needs to operate. Unexpected results for sure , possible damage to the computer may result. Replacing the knock sensor is the best way.

Oct 12, 2014 | 2000 Nissan Frontier

2 Answers

Replacing knock sensor do I need to replace the harrness


No you don't have to change the harness unless it is cracked, broken, or have burn marks.

Nov 10, 2010 | 2000 Nissan Frontier

1 Answer

2000 nissan frontier knock sensor code & distributor


no but the knock sensor does send a signal the ecm and it will ****** or advance the distributor timing

Jun 14, 2010 | 2000 Nissan Frontier

2 Answers

2001 Nissan Frontier 4x4 crewcab supercharged. P0340. won't start. also p0325 power to distributor, no spark, resistor ok, coil resistance ok, distributor checks out ok on scope.


P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)
P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)if you have no spark it your cam sensor

Nov 14, 2009 | 2000 Nissan Frontier

1 Answer

Location of knock sensor


Knock sensors can be difficult to locate because there usually buried under intake or exhaust manifolds and misc. engine wiring and plumbing. Knock sensors need to hear an engine knocking noise, therefore there usually located somewhere they can hear an engine knock. If it's a V6 then possibly it will be between the cylinder heads and access to them can only be attained by removing the intake manifold. I would suggest calling a Nissan Dealer parts person and ask them. Good luck.

Jun 16, 2009 | 2004 Nissan Frontier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...