Question about GMC Cars & Trucks

Open Question

2007 gmc serria stabilitrak problem - GMC Cars & Trucks

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 625 Answers

SOURCE: 2007 gmc envoy

you might have an electric problem since the brake switch comunicates with the transmission module

Posted on May 28, 2008

  • 5 Answers

SOURCE: changing fuel pump on a 1989 gmc serria p/u

buy an aftermarket electric pump from Summit Racing and mount it on the frame rail right near the filter....do not waste time dropping gastanks and paying for ridiculous gm type in the tank pumps, the in the tank pump is a giant fock u to the public from the automakers.....remember the little mechanical cam driven two bolt cuteys? 15 bucks and 15 minutes and you were done.... thanks big three!

Posted on Feb 26, 2009

ftw1952
  • 10319 Answers

SOURCE: how do i bleed my

no scan tool needed
Just start at the furthest wheel away from the Master Cylinder and bleed each on until your up to the master
Then bleed the ABS system last

Posted on Jan 01, 2011

duane_wong
  • 6826 Answers

SOURCE: my 2007 gmc yukon denali's

Stabilitrak uses information from wheel speed sensors. I would have the stabilitrak system codes pulled up to see if any wheel speed sensors are 'locking' up making it seem like you are sliding or locking brakes up, when it is not actually happening. Or, it could be a bad stabilitrak module. Not sure, without seeing if there are any codes in the computer.

Good luck on this repair.

Posted on Feb 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 gmc serria and the engine was knocking full of oil then suddenly lost all oil pressure why


Catastrophic. Do not try to drive it. Have diagnosed at reputable shop. don-ohio

Dec 23, 2016 | GMC Sierra Cars & Trucks

1 Answer

What is making my stabilitrak light staying on


StabiliTrak service light - Chevy TrailBlazer, TrailBlazer SS and ...

forums.trailvoy.com > ... > 02-09 General Tech Q&A > General

Dec 24, 2009 - 11 posts - ‎7 authors
However, the StabiliTrak system seems to be working, as in my area ... If you have OnStar push the button when the Service Stabilitrak light is on have them run a diagnostic. ... 2007 Chevy TrailBlazer LS .... Choose your make. Service Stabilitrak light comes on
11 posts
Mar 31, 2011
Service Stabilitrak
11 posts
Mar 27, 2011
very strange thing happend/ traction control light ...
8 posts
Sep 2, 2010
Abs and traction control light
11 posts
Sep 20, 2009
More results from forums.trailvoy.com

Feb 09, 2016 | 2007 Chevrolet Trailblazer 4.2

1 Answer

GMC 2007 SERRIA, 0 OIL PRESSURE, LIKELY PROBLEM.


Oil pump shaft broken, Spun main bearing on crankshaft will cover the oil hole on the crankshaft stopping oil flow to the engine.

Dec 05, 2014 | 2007 GMC Sierra 1500

1 Answer

GMC 2007 SERRIA, 0 OIL PRESSURE, LIKELY PROBLEM.


If the oil dipstick shows good oil level, the problem is usually is a failed pressure sensor, which I would have checked ASAP at a shop. If the oil level is very low, top it up, but to avoid serious engine damage you may need to have it towed ASAP to a shop for repairs.

Dec 05, 2014 | 2007 GMC Sierra 1500

1 Answer

Where's the knock sensors on a 2007 gmc serria 1500 5.3L


under the intake plentium right in the middle of the valley between the heads. bad for wires getting corroded and rusted. it holds water in the knock sensor holes, you can buy the harness

Mar 07, 2013 | 2007 GMC Sierra 1500

1 Answer

My 2007 gmc yukon denali's stabilitrak continues to come on. What can I do to solve it or to prevent it from coming on?


Stabilitrak uses information from wheel speed sensors. I would have the stabilitrak system codes pulled up to see if any wheel speed sensors are 'locking' up making it seem like you are sliding or locking brakes up, when it is not actually happening. Or, it could be a bad stabilitrak module. Not sure, without seeing if there are any codes in the computer.

Good luck on this repair.

Jan 31, 2011 | 2007 GMC Yukon

1 Answer

How do i bleed my brakes on a 2007 GMC Yukon with the stabilitrak i've tried and got no where do i need a scan tool


no scan tool needed
Just start at the furthest wheel away from the Master Cylinder and bleed each on until your up to the master
Then bleed the ABS system last

Jan 01, 2011 | GMC Yukon Cars & Trucks

1 Answer

2007 gmc envoy


you might have an electric problem since the brake switch comunicates with the transmission module

May 27, 2008 | 2007 GMC Envoy Denali

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...