Question about Cars & Trucks

Open Question

Chrysler concorde limp in mode reset

Car has all reverse but wont shift out of second went into limpin mode can this be reset

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

juggernautxt
  • 145 Answers

SOURCE: tranny stuck in limp mode

sounds like to prndl switch may be malfunctioning.
gear selector switch, which tells the transmission which gear it is in.

Posted on May 13, 2009

  • 3 Answers

SOURCE: Shift problems in 95 chrysler concorde transmission

Sorry but if your reverse is having trouble you will probably have to replace or rebuild tranny like me. Otherwise try new filter and fluid first.

Posted on Jun 06, 2009

  • 412 Answers

SOURCE: chrysler concorde car wont shift from reverse to park

it sounds like your gearshift cable is broken..if you can jack up vehicle and support it safely,get someone to move shifter and look on driver's side of transmission and see if linkage is moving on trans..linkage is up near top of trans..i have seen this problem before

Posted on Aug 16, 2009

  • 1 Answer

SOURCE: transmission shifts to second gear and stays there

Could Be that your TCM is losing power. I would check to see if the TCM is firmly attached to the passenger side fender wall. If not it could be losing the ground.

Posted on Jun 09, 2010

  • 239 Answers

SOURCE: 2000 chrysler 300m

The 700 is the limp mode, as I recall. One or both of the sensors are failing, and they are not too expensive to replace. Once replaced, then using the OBD tool, you can delete the fault codes and then be able to shift into all the gears.
I have written about this solution in other blogged questions, and so have others. Under the car, on the Driver side of the transmission are two electric sensors. They lay horizontally on the trans just behind where your foot would go on the accelerator and under the floorboard. The electricl clip sockets pull out with thumb pressure on each socket. DO NOT pull on the wires EVER. Unplug each socket, and replace one at a time. Use a 1" deep well socket and unscrew them from the side of the trans casing. Do one at a time starting with the one on the left, the Input side,; Then the output side.
The reason why I replace them both is that they are cheap- about $20 apiece- and REALLY: do you want to go under there twice for twenty bucks? If so, then just replace the one on the LEFT- the Input sensor. You then MUST RESET THE CODES with the OBD tool for the transmission side of the tool, then GO!

Posted on Dec 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the speed sensor located on a 2002 Chrysler Concorde


Beware speed sensors seldom fail. Chrysler products transmission have a limp mode where they only shift to second gear when something goes wrong and many times when nothing is wrong. If the speedometer fails it goes to limp. If an OBD scan gives a transmission code sometimes clearing the code will end the problem. When driving if the transmission shifts one time as it should the sensor is working.

Sep 01, 2014 | 2002 Chrysler Concorde

1 Answer

CODE PO871


First thing tomorrow, take it back to the shop that rebuilt it!!

Jul 03, 2017 | Dodge Pickup Cars & Trucks

1 Answer

My 98 concorde is stuck in second gear and the speedometer quit working at the same time what would make it do this


I would say the speed sensor in the transaxle is the problem with both issues. The body computer needs the speedo to tell which gear to use, and second gear is the default when the system is in fail mode.

Aug 28, 2012 | Chrysler Concorde Cars & Trucks

2 Answers

My 99 chrysler concord speedometer quit working and it wont shift out of 2nd gear. What is wrong?


Chances are the check engine light came on also. You should have the vehicle scanned for codes, it could be that the output speed sensor has failed. This could put the transmission into limp mode (second gear) and cause the speedometer not to work. I would guess this to be an inexpensive repair, .6 hours labor plus the cost of the sensor, $16.99 at O'reillys ...I hope this helps

Mar 19, 2011 | 1999 Chrysler Concorde

1 Answer

Car will not shift out of second gear. while driving it shifts fine to second gear from first gear but it stays in second gear the entire time driven


it is going in limp mode,
if your speedometer is not working will cause this,that would be a speed sensor,or the other two reasons would be the input or output sensors on the tranny

Nov 29, 2009 | 1994 Chrysler Concorde

1 Answer

Chrysler concorde car wont shift from reverse to park


it sounds like your gearshift cable is broken..if you can jack up vehicle and support it safely,get someone to move shifter and look on driver's side of transmission and see if linkage is moving on trans..linkage is up near top of trans..i have seen this problem before

Jul 30, 2009 | 2000 Chrysler Concorde

1 Answer

NO GAUGES & WON'T SHIFT TRANSMISSION


I would have the high and low shift sensors replaced first. If it continues to not shift it is staying in limp mode and you need to take it to trans shop to have diagnostic

Jun 29, 2009 | 1994 Chrysler Concorde

2 Answers

Chrysler concorde doesn't shift out of first


It sounds like it is in limp mode, this means that there is a transmission problem. The trans will go into limp mode to protect from further damage. You need to take it to a trans shop to have diagnostic test

Mar 04, 2009 | 1998 Chrysler Concorde

1 Answer

1997 dodge caravan wont shift out of first gear


Yep ,sounds like limp mode ,should be in second gear.
Try,key on engine off,depress accelerator to floor 3 times within 5 seconds.Should reset trans.

Dec 13, 2008 | 1996 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...