Question about Cars & Trucks

Open Question

How to connect the t for 1996 bmw 328is vacuum

I cannot find connection for vacuum t under the intake manifold of a 1996 bmw 328is

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Volkswagen polo 1.4 TDI intake manifold

The man is right my fellow water for gas enthusiast... abort that system before it does damage to your tdi engine.

helping hand

Posted on Jul 08, 2008

Ad
  • 28 Answers

SOURCE: vacuum leak

plastic cover must come off to repair hose< hope you have a garage friend he will help you if not post it again i will ask my mechinic.

Posted on Feb 22, 2009

  • 92 Answers

SOURCE: fuel pressure regulator had no vacuum line connected

another engineers wet dream. think of it this way . what is normally in the intake when the engine is running.. answer vacume, hence the regulator gets its vacume without a hose connected to it as its already in a full time vacume chamber.no hose required . ps be carefull to seat the regulator and o rings securely into the housing befor you reattach the secureing metal clip.
good luck chris

Posted on Mar 23, 2009

  • 1 Answer

SOURCE: water leak under the intake manifold,1995 toyota 4 runner

There is a heater core bypass pipe that runs from the block (under the manifold) to the bacl of theengine where you will see a flat rectangular "sheet metal" thing with a pipe coming out of it. The a rubber hose connects. You need to pull the top air plenums and intake to get to it. The p[ipe flange bolts to the block with silicone rtv as a sealant.

Posted on Nov 27, 2009

Testimonial: "thanxs"

  • 246 Answers

SOURCE: 1996 land rover discovery intake manifold gasket

oil from the pcv valve going into your intake manifold will cause a gasket to swell. but it should not be to the point where it's noticeable. you should probably replace the intake manifold gasket at this point.

Posted on Feb 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the interior fuse box on an 96 BMW 328is


There are 3 fuse boxes on the E36 range on european models there are two on the the drivers side, one under the steering column & one to the right of the steering column, & another fuse box on the left of the car at the glove box

Mar 02, 2013 | 1996 BMW 3 Series

1 Answer

Took to inspection code p0171


engine running lean. Usually caused by vacuum leak. If you have a V engine, the failure is usually intake manifold gaskets. If you have inline (4-cylinder), the cause may be intake gaskets or bad or unhooked vacuum hoses attached to the intake manifold. Check all vacuum hoses for cracks or loose connections. Replace any suspect hose. To find manifold gasket leaks, spray ether or carb cleaner on the gaskets with the engine running. If the engine revs at all, you have a leaky gasket and must remove the manifold to replace. Please let me know if you have any more questions.

Oct 30, 2010 | 1996 Oldsmobile LSS

1 Answer

Where is the starter in a 1996 bmw 328i


It is on the driver side on the motor below the intake manifold. It is a difficult job to replace unless you know what you are doing. I hear there is a way to do it under the car with like 4 foot of flexible extensions, but know it would be difficult. Usually I take off the intake. Make sure you keep track of the multiple connectors and vacuum lines and tubing.

Aug 29, 2010 | 1999 BMW 328 Series

1 Answer

Torque sequence for 1996 chevrolet van intake manifold with a 4.3 litre moter


Ha, you tried to fool me with the bit about a 3.5 L motor--I could find that one...here is the complete procedure from AutoZone.com:




Installation To install:
  1. Clean the gasket mounting surfaces. Be sure to inspect the manifold for warpage and/or cracks. If necessary, replace it.
  2. Position the gaskets on the cylinder head with the port blocking plates to the rear and the This Side Up stamps facing upward. Then apply a 3 / 16 in. (5mm) bead of RTV sealant on the front and rear of the engine block at the block-to-manifold mating surface. Extend the bead 1 / 2 in. (13mm) up each cylinder head to seal and retain the gaskets.

    0996b43f80208c7b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold tightening sequence-4.3L engines
  3. Install the lower intake manifold. Tighten the bolts in sequence and in 3 steps, as follows:


    1. Step 1: 26 inch lbs. (3 Nm).
    2. Step 2: 106 inch lbs. (12 Nm).
    3. Step 3: 133 inch. lbs. (15 Nm).

  4. Install or connect the following:

    Power steering pump Alternator bracket bolt near the thermostat housing Wiring harness to the lower manifold components, including the injector, EGR valve and ECT sensor Air conditioning compressor bracket-to-the lower intake manifold pencil braces
  5. Install transmission oil dipstick tube, if necessary.

    Fuel supply and return lines to the rear of the lower intake
  6. Temporarily reattach the negative battery cable, then pressurize the fuel system (by cycling the ignition without starting the engine) and check for leaks.
  7. Disconnect the negative battery cable.
  8. Install or connect the following:

    Heater hose to the lower intake Upper radiator hose to the thermostat housing Distributor assembly and engage the wiring Ignition coil Connect vacuum hoses to the upper and lower intake manifold. New upper intake manifold gasket, making sure the green sealing lines are facing upward Upper intake manifold Manifold retainers. Tighten them to 88 inch lbs. (10 Nm) using two passes. Purge solenoid and bracket Brake booster vacuum hose at the upper intake manifold PCV hose to the rear of the upper intake manifold Vacuum hoses to both the front and rear of the manifold assembly Throttle body Throttle linkage to the upper intake Wiring to the upper intake components including the TP sensor, IAC motor, MAP sensor and the fuel meter Engine cover Air intake assembly
  9. Connect negative battery cable.
  10. Refill the engine cooling system.
  11. Start the engine and check for leaks.

Aug 26, 2010 | 1996 Chevrolet Astro

1 Answer

My car is idling too fast, where is the idle cable,so i can alter its idle speed , i have a 1995 bmw 316i se


it's not old carbureted chevy, it's not idling high because there's too much tension on the gas pedal cable.

look at replacing/cleaning: idle control valve, maf(mass air flow sensor) vacuum leaks: intake manifold or air intake system.

Jul 03, 2010 | 1996 BMW 318

1 Answer

How to replace the starter on a 1996 Kia Sephia


under the intake manifold towards the firewall attatched to the transmission take intake manifold braket off it should have one bolt on the bottom and two on the top connected to the intake manifold then the starter will be to the left of that if your under the car its almost impossible to reach from above the car. three bolts will hold the starter in then disconnect and it should pop right out.

Apr 19, 2010 | 1996 Kia Sephia

1 Answer

BMW 325i 1993 has broken connections on cylindrical thing under mass air flow sensor with blue tube connection that runs next to the fuel lines uner the car. What is it?


This is the Charcoal Canister. It is a part of the fuel tank vent system. If you have broken nipples, where the hoses connect, you will have vacuum leaks between the intake manifold and the fuel vent system which will affect the way the engine runs. You should replace the canister.

You can purchase a new canister at Bavarian Autosport. See the link below.

http://www.bavauto.com/shop.asp?HC1=0&Htarget=search.asp&HCY=1993&HCM=325i&SearchStr=charcoal%20canister

Nov 02, 2009 | BMW 325 Cars & Trucks

1 Answer

96 328is starter location


Under the intake manifold

Aug 20, 2009 | 2008 BMW 1 Series

1 Answer

1996 Sentra EGR vacuum line connection


listen for the hiss sound,the take off should be on the inlet manifold somewhere near the throttle body .but havent worked on one to say exactly where ,

Aug 17, 2009 | 1996 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...