Question about Cars & Trucks

Open Question

Location of crankshaft sensor on 2004 nissan navara 3.0 diesel

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
pal03246
  • 726 Answers

SOURCE: crankshaft poistion sensor location for

Its right next to the passenger side drive shaft, where it goes into the transmission. Right above the drive shaft. It s black with green slider inside of the connector and it has 3 wires coming out of it.

Posted on Jul 24, 2008

Ad
polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

SOURCE: WHERE IS THE CAM POSITION SENSOR LOCATED ON A 2004 NISSAN MAXIMA

WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....



Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...



you all enjoy your rides out htere!!!

Posted on Jul 01, 2009

  • 1 Answer

SOURCE: crankshaft position sensor for 2004 nissan sentra.

will the crank sensor cause the vehicle to shut down while running?

Posted on Aug 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft sensor position located on a 2004 V8 Nissan Armada


The crankshaft position sensor is located on the transaxle housing, facing the gear teeth of the drive plate.

Jan 18, 2017 | 2004 Nissan Armada

1 Answer

Nissan navara 2002 twin cab diesel zd30 malfunction light comes on randomly


NISSAN NAVARA questions and answers

www.roadtestreports.co.uk/vans/nissan/navara/qanda/
Results 1 - 40 of 322 - Ask and answer questions on a variety of NISSAN NAVARAmodels. Help and advice ... Have a Navarra Rally Raid 2004 double cab pick up. ... Navara V6 2011 - loss of power & engine management light on. .... ZD30 I have changed the diesel filters after noticing that it's jerking when I'm on full throttle.

Nissan Patrol GR Y61 ZD30 starting problem - YouTube

? 1:23
https://www.youtube.com/watch?v=JxHKfYDCgFQ
Jan 16, 2013 - Uploaded by sspyropoul
After replacing the diesel filter seals and water trap i had no problem .But you ... They still glow for like 15 ...Missing: twin ‎cab ‎randomly

Nissan D22 Navara receives YD25 2.5-litre diesel

www.themotorreport.com.au/.../nissan-re-power-their-d22-navara-range
Jan 31, 2008 - Nissan's popular Navara D22 workhorse range has been ... On top of the 4x4 DX single cab's equipment, the dual cab ST-R adds .... the yd25 engine have a overheating problem, so how comes nissan is ... I believe it is a ZD30 engine. .... with no problems except a cracked injector line (pretty random fault).

Jan 13, 2016 | Nissan Cars & Trucks

1 Answer

Audio wiring diagram for 04 nissan navara needed. with colour coding please


This model is also called Nissan Frontier2001-2004 Nissan Frontier (North America) Nissan D22 Navara (Australia).

Then, check this:
2004 Nissan Frontier Truck Car Radio Stereo Audio Wiring DiagramCar Radio Battery Constant 12v+ Wire: PinkCar Radio Accessory Switched 12v+ Wire: BlueCar Radio Ground Wire: GrayCar Radio Illumination Wire: Red/BlueCar Stereo Dimmer Wire: Red/YellowCar Stereo Antenna Trigger: N/ACar Stereo Amp Trigger Wire: N/ACar Stereo Amplifier Location: N/ACar Audio Front Speakers Size: N/ACar Audio Front Speakers Location: N/ALeft Front Speaker Positive Wire (+): PinkLeft Front Speaker Negative Wire (-): BlueRight Front Speaker Positive Wire (+): WhiteRight Front Speaker Negative Wire (-): BlackCar Audio Rear Speakers Size: N/ACar Audio Rear Speakers Location: N/ALeft Rear Speaker Positive Wire (+): Light GreenLeft Rear Speaker Negative Wire (-): VioletRight Rear Speaker Positive Wire (+): BlueRight Rear Speaker Negative Wire (-): Pink

Hope this helps.

Apr 23, 2012 | Nissan Navara Cars & Trucks

1 Answer

Where is the crankshaft sensor for the 1997 nissan quest located?


For 1997 Nissan/Datsun Truck Quest Mini Van 3.0L SFI 6cyl the Crankshaft Position Sensor is located: Under hood, center, upper engine area, mounted on top front driver side of engine.

Hope helps (remember comment and rated this).

Jul 26, 2010 | 2004 Nissan Quest

2 Answers

Where is the crankshaft sensor located ?


The crankshaft position sensor (POS) is located on the oil pan facing the gear teeth (cogs) of the signal plate. It detects the fluctuation of the engine revolution.
After replacement, ECM reprogramming is required.
This vehicle may be subject to voluntary recall, CAMPAIGN I.D. # R0606, that involves the crankshaft position sensor:

Quote: Nissan has determined that on some 2003 - 2004 Altima and Sentra vehicles with the 2.5 liter engine the operation of the crank angle sensor is significantly affected by variations in temperature that occur due to the unique location of the sensor in the engine. Under certain driving conditions, these variations in temperature can be large enough to cause a brief interruption in the signal output from the sensor. If the interruption in the signal from the sensor is so brief that the Electronic Control Module (ECM) logic does not have time to diagnose the condition, the engine may stop running without warning while the vehicle is driven at low speed.

Jun 29, 2010 | 2004 Nissan Sentra

1 Answer

Crankshaft position sensor for 2004 Nissan 1.8 eng.


This sensor is located at the crankshaft pully . the sensor is mounted on the block

May 22, 2009 | 2004 Nissan Sentra

2 Answers

Navara d22 on 53 plate missing at 2.500 r.pm and


i had a similar problem it turned out to be a neuteral selecter sensor located on the gear box

May 09, 2009 | 1997 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

515 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...