Question about 2000 Pontiac Grand Am GT

Open Question

Where is mall pgm module located on my 2002 grand am GT body?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2039 Answers

SOURCE: 2002 pontiac grand am gt , 3800 v6

there is none you have to remove a plug on the trasm its on the passager side near axle shaft engine running in park remove plug if oil come out its full if no oil add gm trany oil you see it on top of trany big red nod be carefull it hot there cheers pierre

Posted on Jun 24, 2008

Ad

SOURCE: body control module location

the location of the bcm is at the passenger side glove box area12900_pcm_2.jpg

Posted on Apr 23, 2009

  • 1 Answer

SOURCE: where is the MALL PGM plug 2006 pontiac g6

Where is the MALL PGM fues on a 2001 Gram Am.

Posted on Dec 24, 2009

  • 389 Answers

SOURCE: Regarding 97 sunfire remote locks control problem

I don't know the name of it but it may be just under doors. My sugestion is to remove every fuse one at a time and look to see if it has a seperation in the little wire inside the fuse. If so then replace that fuse. You may have more then one burnt fuse so take them all out one at a time and replace them as necessary. Also make sure the battery is good in your hand held remote. I hope this helps, The Raz

Posted on Apr 17, 2010

chromapr
  • 267 Answers

SOURCE: tail lights & dash lights went out.

not likely to have a relay in these circuits. to lose both of these something else like a ground could be the problem. try the tail lights first do you have any thing? brake lights backup light , running light. look for fuse in inside fuse box and check for voltage at the fuse. need more info from you. good luck

Posted on Apr 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Mall PGM fuse located on a 2003 Chevrolet Monte Carlo SS


Your vehicle doesn't have MALL PGM fuse . What is it your trying to do ?

Feb 28, 2017 | Chevrolet Cars & Trucks

1 Answer

How do I program keyless entry on my 2002 grand prix? I have tried the way I found by removing mall pgm fuse n open door n turn key to acc. Doesnt work. The fob I have was for gp why it not work?


Important: All transmitters which are to be recognized by the remote control door lock transmitter (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to four transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle.
  1. Remove the ignition key from the ignition lock cylinder.
  2. Close all of the doors.
  3. Remove the MALL PGM fuse from the fuse block.
  4. Insert the ignition key into the ignition lock cylinder.
  5. Turn the ignition to ACC.
  6. The body control module (BCM) will perform the following in order to identify the type of BCM installed in the vehicle:
    ?€¢
    Flash the seat belt indicator 1, 2, or 3 times.


    ?€¢
    Chime 1, 2, or 3 times.

  7. Turn the ignition to OFF, and then back to ACC within 1 second.
  8. The BCM may begin to chime and flash diagnostic trouble codes (DTCs). If the BCM has stored any DTCs, refer to Diagnostic System Check - Body Control System in Body Control System.
  9. Open and then close any vehicle door.
  10. The BCM will chime in order to confirm that the programming mode has been entered.
  11. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for approximately 14 seconds.
  12. Important: After approximately 7 seconds the BCM will chime once to confirm that synchronization has been completed. After approximately 14 seconds the BCM will chime a second time to confirm that the programming has been completed.
  13. Repeat the previous step in order to program each additional transmitter.
  14. Remove the ignition key from the ignition lock cylinder.
  15. Install the MALL PGM fuse into the fuse block.
  16. Operate the functions of each transmitter in order to verify correct system operation.

Jun 12, 2015 | 2002 Pontiac Grand Prix

1 Answer

WHERE IS THE MALL PGM FUSE PANEL LOCATED ON A 2000 PONTIAC GRAND PRIX


There is a 10A MALL/CLUSTER FUSE in the fuse block. There is no MALL/PGM fuse panel.

Oct 22, 2010 | 2000 Pontiac Grand Prix

1 Answer

Where is the mall pgm


These are normally located in engine and are easy to spot black boxes .

Jun 22, 2010 | 2005 Pontiac Grand Prix

1 Answer

I need to program the key less entry


IMPORTANT: Before entering programming mode, have in possession all of the remotes you
will be useing on the vehicle. Once you program the remote. all previous remotes that were
programmed will be erased from memory. The other remotes will not be functional until you
program the them again.

1. Remove the key from the ignition.
2. Close all doors.
3. Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or
owner's manual to properly locate the "MALL PGM" fuse.

4. Insert the key into the ignition, and turn to the ACC position.
5. Turn the key to OFF and then back to ACC within 1 second.
6. Open and close any vehicle door. A chime will be heard when the system enters into
programming mode.

7. Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds.
IMPORTANT: After 7 seconds, a chime may be heard confirming successful
synchronization. It is necessary to wait approximately 14 seconds for a second chime
that will confirm successful programming.

8. Repeat step 7 now for each additional remotes to be programmed including any existing
remotes.

9. Remove key from ignition.
10. Install the "MALL PGM" fuse back into the fuse panel and test remote(s).

May 10, 2010 | 1998 Pontiac Grand Prix

1 Answer

How do you program the remotes for keyless entry with a 200 pontiac grand am?


Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:

Sit in the vehicle driver's seat.
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation

Oct 21, 2009 | 2000 Pontiac Grand Am GT

Not finding what you are looking for?
2000 Pontiac Grand Am GT Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...