Question about Cars & Trucks

1 Answer

I have fault code come up on our sullair 375 compressor the engine will start up and run for about 2 minutes and shut down with a spn-970 / fm1-31 ext aux shutdown switch and not sure hwere else to look. looking for some advise thank you

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,109 Answers

You may have this posted in the wrong product category. Please select another category appropriate to the problem and re-post the problem so the correct expert will see and respond to the question..
This is for car and truck problems related to Factory Installed Systems not add on aftermarket systems.
This post can't be removed or moved, please re-post the question in the correct product category. Thanks

Posted on Nov 01, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Ray190te
  • 61 Answers

SOURCE: Engine shut down

Check your fuel pump relay ,situated behind the battery next to the ABS and engine ECU it a small black box (not the one that says Klima)

Posted on Jan 21, 2009

Molson02536
  • 3854 Answers

SOURCE: 97 Dodge Caravan Auto-Shutdown Problem

Been working on my dad's 97 Caravan longer then i can remember for things you mentioned and have been not able to get him to sell it.
I found that the electrical connections are prone to corrosion and have replaced lots of the wire and pin connection in the wire harness, thank god i have time on my hands.
The instrument panel where the wire harness connects, i found that the solder goes bad and i had to re solder the connector on the back side of the circuit board, where the harness goes so you need to remove the instrument panel from the dash,
Here is a link that can help you retrieve DTC codes and do research on your caravan. I'ld tell you everything what i needed to do to keep my dad's caravan running but that would be a novel. http://www.allpar.com/fix/stall.html

Good luck and keep me posted, glad to help you keep yours running too.

Posted on May 26, 2009

Molson02536
  • 3854 Answers

SOURCE: A/C compressor cycles on/off

You could have a slow leak and the system is low on R134 and soon will stop running. The other thing to look for is the relay to the A/C compressor and switch it with an other relay or just replace it since there not that expensive. The pressure switch is an easy replacement to do, you just have to be quick so you don't lose all the R134 out of the system. Recap, recharge the system and get a proper reading on your high and low side A/C lines. To much R134 will also give you the same problem. Good luck and hope this helps.

Posted on Jun 04, 2009

  • 7 Answers

SOURCE: 2005 DB9 / crank no start

pull out negative terminal battery located under rear right seat.wait for 5 min n then install again the lead negative terminal.insert the key to ignition cylinder.turn the key on off three times.now start the engine.make sure u use recommended fuel grade.

Posted on Jun 21, 2009

jeffbvegas1
  • 520 Answers

SOURCE: 1992 Chevy S10 blazer 4wd (4.3 TBI engine code Z).

Replace ECM

Posted on Aug 15, 2009

Testimonial: "Thank you for your expert recommendation - right on the mark."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fault code 1 Fail 31 Spn1569 2015 Cascadia Cummins engine


spn 1569 relates engine protection torque derate -condition exists.
critical fault codes related to engine operation are active
code 1 means urgent attention
A sort of limp mode setting that requires immediate attention by a cummins service center to prevent further damage to the engine
go google and type in--- cummins engines fault codes (or cummins engine fault code 1569) and there are pages of pdf downloads that list all the codes and what they stand for

Oct 07, 2015 | Cars & Trucks

1 Answer

Engine starts but cannot speed up


sounds like you have a pressure switch sticking or has failed .

Aug 11, 2015 | Cars & Trucks

2 Answers

Kenworth 2014 t800 with Paccar motor. Fault codes SPN:5109 and SPN :3217. Just wanted to know what they're for.


Spn codes are not very good indicators of what's going on.
This is a general protocol that all manufactures use and I don't find it reliable. If there is an engine light on with a wrench in it. Get to the dealer. If there is no wrench it's not as urgent.

Aug 02, 2014 | Cars & Trucks

1 Answer

Jeep shuts down while driving, but will start back up in 1 or 2 minutes


Check for a fault code set using keydance: ignition switch off/run three times and leave in run at third time. Odometer will show Done when no faults, or a fault code(s). This many times is a problem with crank or cam sensor.

Apr 07, 2014 | 2001 Jeep Grand Cherokee

1 Answer

Cummins engine fault codes


Year, make, model, engine size?

Aug 21, 2013 | Volvo Cars & Trucks

1 Answer

Type of d a torque fluid used in sullair 185Q air compressor


contact sullair for this as the correct oil is essential for good performance. You may find the information on the web under sullair compressors.

Jul 21, 2013 | Cars & Trucks

1 Answer

=1995 volvo road tractor symptom [engine shuts down] code; active,engin e, intake,air,tmp,short,+v


I recently came across a similar situation in a isuzu that took some time to diagnose. What if eventually turned out to be one injector had an intermittent failure and it too out 2 other injectors and the engine shut down. If the vehicle sat for 1/2 hour it restarted and ran again for sometimes days before the fault again appeared. It was tracked down by running the truck on a chassis dyno under load and when the fault appeared each injector was disconnected until the faulty one was revealed. If these symptoms parallel yours I suggest you point the mechanic in that direction .

Mar 11, 2013 | Cars & Trucks

1 Answer

Truck will be running fine, then all of a sudden it will completely shut off. After we wait a few minutes and pump the clutch and make sure it is all the way to the floor it will start, sometimes. S


You need the engine computer scanned for fault codes, i thank you have an ignition control problem like a module or distributor pickup coil issue. These parts whenthey fail should leave fault cdes so get them read.
Next, the check engine light will pause shortly followed by the second digit of the trouble code. For example if the check engine light blinks once and pauses followed by six blinks the trouble code number would be 16. If no code is present the check engine light will stay one constantly. To restart code gathering turn the ignition key to the "off" position, wait three minutes and turn the ignition key back "on" again without starting the engine. Remove the jumper wire once code gathering is complete. To clear code after the repairs have been made remove the negative battery cable for one minute and reconnect.
toyota_dianostic_connector.jpg
Toyota Diagnostic Connector
Toyota Code Definition Table
Code 11 Momentary interruption in power supply to ECU (electronic control unit or computer) up to 1991
Code 12 Engine revolution signal missing Code 13 Rpm signal to ecu missing above 1000 rpm
Code 14 Igniter signal to ecu missing
Code 16 A/T control signal missing from ecu
Code 21 Main oxygen sensor signal fault
Code 22 Water temperature sensor circuit fault
Code 23 and 24 Intake air temperature signal fault
Code 25 Air/fuel ratio LEAN
Code 26 Air/fuel ratio RICH
Code 27 Sub-oxygen sensor signal or heater circuit fault
Code 28 No. 2 oxygen sensor/heater signal fault
Code 31 and 32 Air flow meter circuit or Vacuum sensor signal fault Code 34 and 36 Turbo-charging pressure signal fault
Code 35 Altitude compensation sensor signal fault
Code 41 Throttle position circuit fault
Code 42 Vehicle speed sensor circuit
Code 43 No starter signal to the ecu
Code 51 AC signal on; DL contact off (in transmission shifter with diagnostic connector jumped)
Code 52, 53 and 55 Knock sensor fault Code 71 EGR system malfunction
Code 72 Fuel cut solenoid signal fault
Code 78 Fuel pump control signal fault
Code 81, 83, 84 and 85 TCM communication fault

Jun 28, 2012 | Cars & Trucks

1 Answer

We have a 96 2.0 eclipe. runs great till warms up then dies. has new fuel pump & coil pk. please help


Well you should not guess it can be costly!you should have a check engine light on. So you should have a OBD 2 scan done to retreve you fault code to fix your problem.However your problem is most likely"""most likey a Bank 1 O2 sensor the one in the engine manifold before the cadilac converter sounds like it is stuck in midrange! These 2.l are 'famous' for it soon as it cools down for a minute starts runs for a minute then shuts off corect!

Dec 26, 2009 | 1996 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

487 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...