Question about Chrysler Cars & Trucks

1 Answer

Radio lights flashing

Disconected battery to replace blower resistor. Reconected battery and now radio does not work, equaliser juts flashes. took to dealership and they said that, equiliser lights flashing radio does not work - found power at pins 6 + 7 at c2 connector and now power at pin @8+7 of C4 connector ??? Why does radio not work?

Posted by on

  • 1 more comment 
  • Jamie Alton
    Jamie Alton Nov 01, 2012

    Does the radio require a radio pin security code?Check owner's manual and report please.

  • Mel Dobres
    Mel Dobres Nov 01, 2012

    dealer says this model does noy have any code??

  • Mel Dobres
    Mel Dobres Nov 02, 2012

    The mechanic made the opening quote to me re the lack of power??



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Chrysler Master
  • 79,865 Answers

I think the dealer is worng on this code info.

Posted on Nov 01, 2012

  • Mel Dobres
    Mel Dobres Nov 02, 2012

    Hi Dennis, Two dealers say the same thing "there is no code for this model" I don't know if it being a Canadian car makes any difference?? Just **** enoying



6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 132 Answers

SOURCE: 2000 Pontiac Grand Prix interior fan speeds 1-4 not working

Check the ground, the resistors are accully resisnting the Negitive Current.

Posted on Jul 30, 2008

  • 1861 Answers

SOURCE: 1993 Camry Check Engine Light

Therre is no DTC code "5". The DTCs start at 12. If the knock sensor (there are actually 2) was bad, you would have an acceleration issue. The knock sensor changes the timing of the spark to eliminate detonation, or "pinging". Do you have a "Ping" condition/valve rattle on acceleration?
To reset the light, open the hood, remove the 15 amp EFI fuse for 5 minutes. Replace it, and start the car and drive it until it reaches operating temperature. If the light comes back on instantly, you have a bad sensor or a bad wire.

Posted on Nov 10, 2008

  • 1498 Answers

SOURCE: No trailer right turn signal or brake light

Hey Boon,

The pinouts for a 7-way plug are as follows:
Seven wire Trailer plugs:

Horse, stock or utility trailers:

White = Ground - 1
Blue = Electric Brakes - 2
Brown = Tail and clearance lights - 3
Black = Battery, aux power - 4
Yellow = Left turn/Brake - 5
Green = Right turn Brake - 6
Orange or Purple (not both) = Auxilliary or Reverse - 7

Recreational Vehicle:
White = Ground - 1
Blue = Electric Brakes - 2
Green = Tail and clearance lights - 3
Black = Battery, aux power - 4
Red = Left turn/Brake - 5
Brown = Right turn Brake - 6
Yellow = Auxilliary or Reverse - 7

In both cases 4 is battery and 7 is reverse, aux or not used.

Double check your wiring using these lists as a reference.

Click here for my post on Trailer wiring

This should get us closer to the answer.

Best regards,

Posted on Sep 09, 2009

  • 1 Answer

SOURCE: Want to install a jack to connect ipod to radio

I have heard of a way to wire this (5) pin connector to headphone cable


[ PIN A ] [EMPTY ]

Loop together PINA and PIND with a 1.5K Ohm Resistor

Posted on Jan 26, 2010

  • 1 Answer

SOURCE: Need help replacing fusible link connector

It doesn't matter because they all carry +12V to the respective circuits. What does matter is which fusible link goes to which circuit (assuming they are different) but if you didn't cut them off, then they should still be connected to the correct circuits.

Posted on Jun 14, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

4 Answers

My GMC Sierra 1500 2004 blower motor only works on high speed

Very common issue with those! Most likely will need a blower motor resistor at the least and possible resistor pig tail. They get hot and melt the ends causing a bad connection. If not going to dealer be sure to take bad resistor with you because there are two different styles that look similar until you go to bolt it back up. If replacing the pig tail replace one wire at a time so you do not cross wire it.

Nov 01, 2017 | GMC Cars & Trucks

1 Answer

Cluster not working

you have taken the battery off wrong it negative off the battery first, then the positive wire. taking off live wire first then butting it back on will blow a number of things even the ecu/ abs units.

Apr 11, 2013 | 2003 Chevrolet Cavalier

1 Answer

The heater blower isnt working in my honda civic. i have replaced the control panel thinking it was that, but it still does not work there seems to be a live feed to the blower unit.i took the blower unit...

Check fuses 13 and 37. Also check relay and resistor. The relay is usually in the engine compartment relay box. It should click when the blower switch is turned on. The resistor will show signs of burning if it's bad.

RESISTOR REMOVAL & INSTALLATION The blower resistor is located on the front of the blower housing.

  1. Disconnect the negative battery cable.
  2. Remove the glove box assembly, if required.
  3. Disconnect the resistor wire connector.
  4. Remove the resistor attaching screws.
  5. Remove the blower motor resistor.
  6. Installation is the reverse of removal.
  7. Install the glove box if it was removed and connect the negative battery cable.
  8. 86b51f5.gif

Oct 24, 2010 | 1995 Honda Civic

1 Answer

I disconected the battery and now it is reconected the radio does not work

The stereo is in lock mode because it thinks it was stolen. Usually there is a combination of button presses to unlock. You can get directions from the dealer or most car audio shops, as this is a common problem when adding audio components.

Aug 26, 2010 | 2001 Toyota Celica

1 Answer

Changed battery in a KIA, Sorento with a Delco CD player. Now CD player will not turn on. Have a small flashing yellow led on right of player but that's it. Not sure what to do next.

whenyou disconected the baterry and reconected the radio and clocks reset .you can try it again or you can try. the cd player has its own reset .should be a small hole .take a paper clip and straighten one end with the power on push the clip in the hole.

Aug 06, 2010 | 2006 Kia Sorento

2 Answers

2000 grand prix blower motor only worked on high for awhile now it doesnt work at all

in alot of cases the blower motor resistor burns
if you follow the blower connection to left you will the resistor plugs right in to the blower but make sure you check it before you buy it take it off and inspect it you will see burns on harness and resistor
its under the passiger side dashboard you will see the blower and to the left is the resistor i think you will need a 9/32 socket or 7mm its held by one screw
good luck

May 22, 2010 | 2000 Pontiac Grand Prix

3 Answers

Front blower motor on 2002 dodge grand caravan sport only works on high speed

it's the blower motor resistor , it's behind the glove compartment, just make sure you disconect the neg. for battery first, open the glove comp. and pull the rubber stops towars the center so you can let the glove comp. hang all the way to the floor , the resistor it's in front of you, disconect the two conectors there's one big with 6 0r 8 wires coming out and another with only two, take them out by pressing on the side of each one, remove it , put the new one on , conect the battery and your done. it's about $ 13.00 at o'riellys auto parts .

I hope this fix yor problem.

David M.

Mar 13, 2009 | 2002 Dodge Grand Caravan

1 Answer

Head lights and a/c and heat

I had a similar problem with the blower not shutting off so the dealership replaced the resistor pack under the dashboard.

The blower stopped working several months later and the lights would turn off if you turned the blower to the on position. It was causing a drain on the power so things like the lights and rear defrost did not work. The blower had an internal short and was replaced.

Sep 30, 2008 | 2000 Pontiac Grand Prix

1 Answer

Engeen stop working no reason

Same thing happened to me. I had no current comming to the ignition, no lights in the dash. I took out each relay and put it in again. Also i disconected all wires joining the ignition an reconected again, and any joinings comming from battery to ignition. I dont know what helped but it started anyway and runs fine.

Aug 18, 2008 | 1992 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides