Question about 1999 Chrysler 300M

Open Question

How do i switch the blend door actuator by manually

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jturcotte
  • 7789 Answers

SOURCE: location of blend door or

The temperature door actuator is located at the bottom of the heater housing at the center terminal. It looks like this:

6b48b5c.gif
To remove the actuator

  1. Remove the left and right underpanel silencer ducts.
  2. Remove the two retaining screws from the actuator which are accessible from the right side of the center stack.
  3. Remove the screw from the actuator on the left side.
  4. Pull the actuator straight down from the shaft and disconnect the electrical wire. Upon removal, matchmark the shaft position of the actuator, because the shaft on this motor is keyed.

Posted on Oct 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the door blend actuator on 2009 lincoln mks


Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage
  1. Remove the 2 lower steering column opening cover bolts.
  1. Detach the lower steering column opening cover.
  1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
  1. Position the instrument panel wire harness away from the LH temperature blend door actuator.
  1. Remove the 3 LH temperature blend door actuator screws.
  1. Disconnect the LH temperature blend door actuator electrical connector.
  1. Remove the LH temperature blend door actuator.
  1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage
  1. Disconnect the glove compartment damper from the glove compartment.
  1. Remove the glove compartment.
  1. Remove the RH lower instrument panel insulator.
  1. Remove the RH lower floor console trim panel.
  1. Remove the 3 RH temperature blend door actuator screws.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  1. Remove the RH temperature blend door actuator.
  1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
  2. Mode Door Actuator - Defrost/Panel/Floor Door
  3. Removal and Installation
    NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
    NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
    Mode door actuator and linkage
    1. Remove the 3 defrost/panel/floor mode door actuator screws.
    1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
    1. Remove the defrost/panel/floor mode door actuator.
    1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
    Mode door actuator linkage only
    1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
    Mode door actuator and linkage
    1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.

Nov 10, 2016 | 2009 Lincoln MKS

1 Answer

Kia sportage 2008 v6,I've a problem with AC,In hot weather after 30 mins drive loose conditioned air and hot air start blowing although after switching engine off for may be 20 mins; AC start working


Bad blend door actuator is your cause. You need to disconnect the actuator from the blend door and manually check the blend door. One side of the door switches the heat and one draws air from the ac evaporator.

Jun 06, 2016 | Kia Cars & Trucks

1 Answer

I replaced the heat blend actuator because I was not getting any heat. Now, after replacing, all I get is hot air and no cold. The A/C was working fine just before replacing.


Do you have Manual Climate Control System or Dual Automatic Temperature Control System ?
The temperature control switch:
  • is a potentiometer that outputs a variable voltage to the temperature blend door actuator to set the position of the temperature blend door.
  • initiates closing of the heater control valve. When set to full COOL, a lever on the temperature blend door pivot shaft depresses the pintle of the heater control valve vacuum switch. The heater control valve vacuum switch then applies vacuum to the heater control valve, closing off engine coolant flow to the heater core.
  • is serviced only with the climate control assembly.
You may have disturbed something when changing the actuator , the vacuum switch o vacuum hose .

Oct 21, 2015 | 2005 Ford Explorer XLT

3 Answers

Driver side blowing hot air passenger side blowing cold air


I'm having the same problem except on mine it's the driver's side that's blowing cold. Do you have the pictures in a finer resolution? I can't make them out and when I zoom, they are too grainy. Does the replacement require removing the dashboard? What's the general cost of the acuators? Are they readily available at like NAPA or other parts stores?

Nov 26, 2011 | 2006 Kia Amanti

2 Answers

2004 f350 ford heater blows cool air but hoses are both warm-where do i start looking


check to see if the blend door is moving where you change the temperature setting. I think your blend door is behind the glove box. Here are instructions for removing the actuator. Take it off, plug it back in and see if the motor rotates. Also check to see if you can rotate the blend door by hand. If you can rotate it by hand, the motor is probably broken of the gears are stripped. Let me know if you have questions.
  1. Release the stops and lower the glove compartment door.
  2. Disconnect the connector.
f4b0b74.gif Fig. Blend door actuator-F-250 & 350


  1. Remove the two screws. Rotate the blend door actuator and bracket assembly. Remove the electronic blend door actuator and bracket assembly.
  2. To install, reverse the removal procedure.

Oct 17, 2010 | 2004 Ford F350

1 Answer

My air conditioner is working but won't blow out


Are you saying the temp blend door is not working?
If yes, it's the control head or the temp blend door motor on th plenum case under the dash. Buy used on ebay.

DO you have manaul or electroic controls?

If electronic

A/C Electronic Blend Door Actuator The A/C electronic blend door actuator is located on top of the A/C evaporator core housing (19A553) assembly.
  • Its function is to move the A/C air temperature control door on command from the control assembly.
  • The A/C electronic blend door actuator contains a reversible electric motor and a potentiometer. The potentiometer wiper is connected to the actuator output shaft and moves with the output shaft to indicate the position of the A/C air temperature control door.
  • A five volt signal is applied to the ends of the potentiometer. The voltage available at the wiper indicates the position of the potentiometer. The expressed value of the actuator wiper voltage is sent to the control module and matched with the wiper voltage of the module potentiometer. The printed circuit board then drives the actuator motor in whichever direction is necessary to make the actuator wiper voltage agree with the control module wiper voltage.
-----------------------------------------------------------
manual

#3 is the blend door.

0425af0.gif

May 08, 2010 | 1998 Mercury Grand Marquis

1 Answer

My heater will only blow hot air out of the rear vents from the rear controls. The front vents only blow cold air. Is there a simple fix?


blend door or temp contrl switch is bad.

Section 12-02: Heating and Defrosting 1998 Windstar Workshop Manual
REMOVAL AND INSTALLATION Actuator Motors, Electric Temperature Blend Door
Removal
  1. Remove cassette storage box or center shelf unit, if equipped.
  1. Remove instrument panel ash receptacle (04810) by depressing service lever.
  1. Disconnect electrical harness connector from electric blend door actuator.


    sww~us~en~file=am0101a.gif~gen~ref.gif

  1. Remove three retaining screws.


    sww~us~en~file=am0100a.gif~gen~ref.gif

  1. Carefully pull electric blend door actuator outward and off A/C evaporator housing (19850) assembly.
Installation
  1. Follow removal procedure in reverse order.
  1. Air temperature control door shaft is keyed. Move door to properly insert electronic actuator shaft. Make sure the shaft is completely in and properly seated.

Jan 14, 2010 | Ford Windstar Cars & Trucks

2 Answers

Blend door for front temp control is stuck in the 'cold' position this winter. Is there a way to manually move and fix the door to get some heat?


you have to replace the blend (heat/cold) door motor, you can try to remove motor and turn door and try to jam something in door handle slot ,that the part that the motor turns,hope this helps.

Dec 26, 2009 | 2001 Ford Windstar

2 Answers

1999 Silverado - cannot get the temperature to switch from cool air to warm air when turning the knob to heat.


The temp blend door, or blend door actuator may be faulty. You can check this by watching the movement of the blend door actuator while you turn the temp selector knob. If the actuator is working, then it may be the blend door, or blend door lever broken. If these are ok then the control head may be faulty.

Oct 18, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
1999 Chrysler 300M Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...