Question about 1992 GMC Sonoma

1 Answer

I have dim hazard lights but my blinker works fine ... what could be the problem?

My turn signal works perfectly but my hazard lights are very dim you can olny barley see them at night. what could this be a relay? or bad wiring? i am very mechanically inclined but when it comes to the electrical part it has me beat

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • GMC Master
  • 2,620 Answers

That would be a poor ground.

Posted on Nov 01, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 74945 Answers

SOURCE: turn on L blinker and

To fix this will require a new turn signal switch, this seems to be a common problem with these multifunction switches.

Posted on Oct 22, 2008

  • 99 Answers

SOURCE: turn signals don't work

you should have a flasher for the turn signals as well as one for the hazard flashers turn signal flasher can be in fuse box on drivers side or mounted to steering column

Posted on Nov 30, 2008

mrgreenz
  • 962 Answers

SOURCE: 1998 GMC Sierra Signal Fuse Blowing

it seems you have a short in either one of the lights or interlock. all are connected to the same fuse. trace the wiring from the fuse box back to the component. Using a test light test in between the wires. check for any obvious breaks in the wiring.

Posted on Dec 06, 2008

joecoolvette
  • 5660 Answers

SOURCE: no brake/hazard lights,have running/turn signal lights

Suggest you change hazard flasher 'can' first, then go to the hazard switch. I'm betting it's the flasher can.

Posted on May 11, 2009

cadman000
  • 607 Answers

SOURCE: bottom brake lights and hazard lights do not come on. All other lights work including top brake lights. Fuses and bulbs checked.

Check for power out of brake light switch by brake pedal. Of its faulty , the 3rd brake light will still work. Hope this helps

Posted on May 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blinkers


You should try replacing the turn signal relay, I think its located in the fuse panel.

Mar 23, 2014 | 1986 Chevrolet Camaro

1 Answer

2001 4 Runner blinker problem


The hazards use a separate relay. listen for signal relay clicking to locate the correct relay. Consult your owners manual for fuse and relay layout.

May 26, 2017 | Toyota 4Runner Cars & Trucks

1 Answer

When the blinker is flipped up or down on the column the tail lights dont respond. But the brake lights and the hazards still work fine. Whats the problem?


The turn signal flasher relay may have a problem.Turn on the hazards and follow the clicking sound to the source and usually the hazard flasher and turn signal flasher are very close to each other.Remove the one that is clicking and put it in place of the turn signal flasher.If the Turn signals then work you will need to purchase a new turn signal flasher relay.They are usually just a few dollars.

Jul 29, 2010 | 1986 Ford F 250

1 Answer

Right turn signal light has fast blinker and arrow stays on dashboard after signal has been turned off.


you may have a bad ground for that bulb. turn hazard lights on and see which bulb is out/dim and start there.

Oct 19, 2009 | 2001 Ford Mustang

2 Answers

One blinker stays on while the other blinks fast when lights are


The multifunction switch is faulty. the turn signal control.

Jul 25, 2009 | 2002 Chevrolet Cavalier Coupe

1 Answer

HAVE RPLACED BULBS AND BRAKE SWITCH AND HAZARDS WORK FINE AND BLINKERS WORK TOO STILL NO BRAKE LIGHTS


check the bulbs again make sure the brake and signal light bulb has two filaments in it, the parking lights ony has one filament

May 21, 2009 | 1999 Ford Taurus

1 Answer

No turn signals or emergency blinkers


I had the same problem twice before. Solved it the same way both times. In my case it was the Hazard switch at the top of the steering column. It was stuck. I knew it was that because the signal lights had been functioning perfectly until I parked my car alongside the road with the hazard lights on to do some nighttime fishing and sip a little white lightnin'. (just kiddin' about the white lightnin')

When I got back in my car to go, I turned off the hazard lights but I had no turn signal lights! So I kept pushing that hazard button up and down for about 30 times with my left turn signal arm down until it started working again. So after having this happen to me twice, I learned a valuable lesson: Don't ever use hazard signals in this car.

Dec 12, 2008 | 1998 Lincoln Town Car

Not finding what you are looking for?
1992 GMC Sonoma Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...