Question about Ford Cars & Trucks

Open Question

Location of transmission control module on 95 v6 mustang?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: daewoo nubira transmission control module

Hi, the TCM is located at the passenger side kick panel (LHD), when you remove the kick panel you will see the ECU (engine control module) directly above it is the TCM. I hope this can help.

amf07ph..

Posted on Oct 16, 2008

Ad
  • 2 Answers

SOURCE: Transmission control module, 92 honda accord

It's under the carpet on the passenger's side floor board. There's two boxes under the access panel, I think the TCM is the one on the right? If your's is broken there are probably a couple of capacitors and a resistor that are fried and need to be replaced.

Posted on Oct 21, 2008

  • 373 Answers

SOURCE: mustang airbags

Hi....
On your question, The AIR BAGS will fit. on the screw and the space, because they look the same.
But will Not work. The connectors are a little different.
And the Ressistance is different and 95 and 00.
The Important. On 1998 ford change the Airbag Software, mean the Resistance on the Air bags before 1998 is different that 1998 and UP. Caalled Second Generation AIR BAG System. The Air bag Light will be ON . If you put the 95 on a 00 vehicle.

Ok... I hope this help on your question.
Thank you for use fixya...

Posted on Jan 15, 2009

chuck943
  • 783 Answers

SOURCE: It is a 2001 Mustang GT 4.6 litre Manual

ECT is located to the right(passenger side) of the alternator in the intake manifold.
PCM is located behind the right(passenger) kick panel under the corner of the dash.

Posted on Mar 20, 2009

jrw4u
  • 62 Answers

SOURCE: Transmission Control Module

Before condemning the transmission, I would check the shift cable for proper operation. Look at the side of the transmission where the shift cable attaches. Have someone shift the transmission from PARK to FIRST. The engine should not be running. If the operating lever on the transmission moves, then you probably do have an internal transmission problem. 78151957.gif
If the operating lever does not move, you have a broken shift cable or it has popped of it's attachments at the operating lever or gear shift handle.
78151960.gif
A bad Transmission Control Module (TCM) would not keep it from shifting. In the event of a bad TCM, the transmission would go into fail safe mode and you could continue driving the vehicle.

Posted on Apr 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I install 95 mustang trans in 302 carburater motor


I would not use any one that has a transmission control module unless yours already has one. They do make TCMs aftermarket but you have to wire everything in and make sure its compatable for your application.

May 23, 2015 | Ford Cars & Trucks

1 Answer

Where is the shift modulator on a 95 grand prix v6 301


Modulators are typically located on the side of the transmission. Look for a small diameter vacuum hose down there and follow to the transmission body. That is most likely the modulator.

Good Luck!

Dec 08, 2014 | 1995 Pontiac Grand Prix

1 Answer

I have a 95 ford mustang v6 automatic transmission. whe the ncar is in park i can increase the rpms. once i put the car in gear it barely moves and i can step on the pedal and then rpms will not increase




Hello


The Engine and Automatic Transmission (not applicable to manual transmissions) in this vehicles drive train are fully electronically controlled by a computer called the PCM and TCM (Power Train Control Module, Transmission Control Module). When a problem like this or other drive-ability related problems occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPENDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM. Also always check fuel pressure for correct spec for your make and engine type.


Sep 18, 2012 | 1995 Ford Mustang

1 Answer

95 mustang v6 auto no forward gears but works in reverse had ****** rebuilt and same thing


Maybe your differential is shot and will only allow reverse spin or the transmission was not really rebuilt professionally. Was the transmission checked outside of your car after rebuild? Does your vehicle have a Powertrain Control Module (PCM)? Maybe the module went bad or faulty.

Jun 18, 2012 | Cars & Trucks

1 Answer

Can i use a transmission from a 95 ford mustang 5.0 on a 95 ford mustang 3.8?


There's a chance that it could bolt up without any trouble, but the transmission for the v6 won't be as strong as the one for the v8 and it probably won't hold up for very long.

Aug 11, 2010 | 1995 Ford Mustang

1 Answer

Problems removing 98 ford mustang transaxle


If you are talking about the axle hub nuts,then you may have to use an air impact socket driver and impact sockets.These nuts can be torqued to over 140 FT LBS. Let me know if you need more help.MOE

Jun 22, 2010 | 1995 Ford Mustang

1 Answer

It is a 2001 Mustang GT 4.6 litre Manual transmission. I need the locations of my Power Train Control Module and my Engine Coolant Temp Sensor.


ECT is located to the right(passenger side) of the alternator in the intake manifold.
PCM is located behind the right(passenger) kick panel under the corner of the dash.

Mar 20, 2009 | 2001 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5530 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...