Question about GMC Cars & Trucks

Open Question

Fuse for 2008 gmc yukon denali xl cruise control

Where is the fuse located

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: location of fuse box/panel for 2004 yukon denali xl

There are 2 fuse panels in the Denali.
One is a panel on the drivers side, its on the dash but facing the door.

The ohter is under the dash and above the pedals, this one is much tougher to access.

Your Owner's Manual should tell you where the fuses are that you need to access.

Posted on Oct 20, 2008

Ad
  • 94 Answers

SOURCE: 2005 gmc yukon xl denali service ride control

it has to do with your air ride suspension best bet is take it to the dealer there is probably a problem with a level sensor. hope this helps you

Posted on Mar 16, 2009

Onifade
  • 268 Answers

SOURCE: 2008 GMC Yukon Denali XL.

This is an electronics issue.

See all the fuses.

Cheers.

Posted on Dec 26, 2009

  • 454 Answers

SOURCE: 2002 gmc yukon denali xl, cruise control inop

It is not a resistance problem. As it operates normally, the cruise control is wired to the stop lamps and will operate only when it sees chassis ground through the stop lamps. When you tap your brake pedal, 12 volts is applied, the ground goes away and cruise is deactivated. Because the LED tails are diodes and only let current flow one way, the cruise cannot see ground and will not set or operate. The same symtoms would appear if you had original incandescent tail lamps and both brake lights were burned out.
The solution will be finding the wire from the cruise that senses the brake lights, and connecting it directly to the brake switch, IF the brake switch is grounded when the pedal is not pressed. You may have a relay wired to the brake pedal switch to make this happen. Seek a knowledeable car audio/accesory shop familiar with auto electrical to help you with this.
Good luck!

Posted on May 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cruise control for 2008 Yukon XL


The most common problem is brake light switch, assuming all other items are ok.

Feb 23, 2015 | 2008 GMC Yukon XL

1 Answer

2005 gmc yukon denali xl engine fans dont come on


under the hood I would check the thermostat to make sure it open so that the hot antifreeze reaches the sensor to make the fan start

May 03, 2014 | 2005 GMC Yukon Xl Denali

2 Answers

Where is the cam shaft location sensor located on a 2005 gmc yukon


camshaft sensor located above crankshaft pulley, the camshaft sensor mounted on the front timing cover above the crankshaft pulley.

Sep 17, 2012 | 2005 GMC Yukon

1 Answer

Where is the cruise control fuse for a 2002 yukon xl 2500


Cruise control fuse is 10 Amp, located in the interior - left side of the instrument panel (dashboard).
An automotive 10 Amp fuse will be red in color.

Jan 17, 2011 | 2002 GMC Yukon XL

1 Answer

2008 GMC Yukon Denali XL. Just turned on the car and no audio


This is an electronics issue.

See all the fuses.

Cheers.

Dec 26, 2009 | 2006 GMC Yukon Denali

1 Answer

2003 Denali Yukon, no Brake lights, no Cruise Control, fuse is OK


Check your brake light switch at the pedal. This controls the lights and disengages the cruise when stopping. I'd look there before I go anywhere else. There may just be a wire loose. Could be a simple fix.

Good Luck and hope this helps.

Mar 15, 2009 | 2002 GMC Yukon XL

1 Answer

2002 YUKON XL Denali no brake lights or cruise


FROM LUSTY KID:

Check your bulbs first, I have lost both headlights on my ford at once on account of the bulbs burning out at the same time. Same thing probably happen, you have one filament out. The lights can work, but if the filament for brake is burnt, you don't see brake lights.

As for the cruise control. Check fuse box first. If OK check vacuum hose to actuator in engine compartment for starters.
Advise:

Oct 12, 2008 | 2002 GMC Yukon XL

4 Answers

Location of fuse box/panel for 2004 yukon denali xl


There are 2 fuse panels in the Denali.
One is a panel on the drivers side, its on the dash but facing the door.

The ohter is under the dash and above the pedals, this one is much tougher to access.

Your Owner's Manual should tell you where the fuses are that you need to access.

Jun 15, 2008 | 2004 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...