Question about Cars & Trucks

Open Question

Case 586e wirring diagram

My voltage gauge dont work. engine temp.fuel gauge and and whatever the other one is dose not work and i need a wiring harness i swaped relays and fuses all good

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Fuel pump not getting power 1985 928s porsche

chck out this site, it has free diagrams etc in pdf format:-
http://www.onlinefreeebooks.net/automotive-machinery-power-equipment-ebooks/porsche/wiring-diagram-porsche-type-928-s-model-89-pdf.html

Your problem can also be with the Bosch ECU, these are prone to failing and also control the fuel pump, they can however be rebuilt.

Posted on Jan 22, 2009

  • 5 Answers

SOURCE: 1987 MUSTANG WIRRING DIAGRAM

I have a manual that has all different wiring diagrams in it for the 87. If you want I can try to find the one that you need and email it to you. If you still need it, just email me at brendanryan51095@hotmail.com and ill send it to you.

Posted on Jan 28, 2009

  • 126 Answers

SOURCE: no power from wiring harness to fuel pump on 2000 s 10

on the drivers side left rear frame next to bumper bracket there is a ground for the fuel pump make sure it is not cut or rusty . the 4.3 has a oil sending unit at back of intake it controls fuel pump . oil sensor tells the computer to give power to fuel pump.

Posted on Apr 15, 2009

  • 84 Answers

SOURCE: electric fuel pump wiring harness diagram

Your best bet is to type it in to autozone.com and got to the repair section. it will tell you there.

Posted on Apr 23, 2009

  • 5 Answers

SOURCE: on my 1994 plymouth voyager the 3 wire harness to fuel pump (blue wire) doesn't have 12 volts; should it? fuel pump quit then worked once when hot-wired with 12 volts. fuse and relay is good.

The wire should not be hot until the relay is triggered. The relay does not get triggered until the ignition key is turned on. It will run for 3-5 seconds or until the system pressure it at max.

Posted on Apr 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cadilac cts2005 temp and fuel gauge not working, please help.


check fuse.
temp gauge wiring diagram.

26133568-w4zlfchs4ahiivt0l0i0subw-4-0.png
fuel gauge wiring. Fuse block at the rear right
26133568-w4zlfchs4ahiivt0l0i0subw-4-2.png

Mar 18, 2016 | Cars & Trucks

1 Answer

Why dose my gauges on a 2004 chevy venture my fuel gauge works but my temp dosent or my speed dont they are pegged out


I replaced the instrument panel ($40 used part and 45 minute
repair with the help of youtube)

Sep 11, 2014 | 2004 Chevrolet Venture Passanger

1 Answer

1990 gmc K1500 5.7L, temp. gauge not working:


To review, you have two temp sensors, one for the gauge on the dash and one for the computer. If you unplug the sensor for the computer the reading will be minus 30 degrees or over 300 which will make it very hard to start. Unplugging the sensor for the gauge would have no effect on the computer.
According to the wiring diagram, the wire for the temp gauge is green, and the wires for the temp sensor for the computer are yellow and black.

Aug 24, 2012 | 1990 GMC Sierra

2 Answers

2004 Ford Taurus, Tach and fuel gauge going crazy


Ford 150 Van No Start No Crank Same problem aftermarket remote start problem !
Watch the second part too . Do you know what a wiring diagram is ? Look under dash or the hood an see where the remote start is hooked up , what wires ! You can find a wiring diagram here at http://www.bbbind.com/free_tsb.html Enter the vehicle info. year , make , model an engine size . Under system click on engine , then under subsystem click on starting . Click the search button , then on blue link . You'll see all the componets in the starter circuit .

Apr 11, 2017 | 2004 Ford Taurus

1 Answer

Just bought an 88 ford bronco 5.0L and the temp gauge and fuel gauge both dont work


u need to remove the access panel for the rear window.ther u will find the moter for the window bare the wires and jumpthe wire with a pos connection.i dont remember witch wir e but u will now when the window gos down does the inside switch not work?

Mar 30, 2011 | 1988 Ford Bronco

1 Answer

Audi 80 fuel and temp gauge problems temp dont work fuel gauge works sometimes


if temp, does not work, it may be the tempurature sending unit. for fuel guage it is usually a bad wire to tank or the sending unit in tank. check wire and ground to tank first. good luck!!

Jul 26, 2010 | 1998 Audi Cabriolet

1 Answer

1992 toyota Corolla Temp gauge does not work


find the wire that goes to temp sender and apply earth to it turn ignition on the temp gauge should read hot if it does replace water temp sender if gauge dose not move gauge needs replaging

Jan 26, 2009 | 1992 Toyota Corolla

1 Answer

1987 MUSTANG WIRRING DIAGRAM


I have a manual that has all different wiring diagrams in it for the 87. If you want I can try to find the one that you need and email it to you. If you still need it, just email me at brendanryan51095@hotmail.com and ill send it to you.

Jan 04, 2009 | 1987 Ford Mustang

1 Answer

2001 Jeep Grand Cherokee Engine temg gauge not working


If you changed the coolant temperature sensor and it had a 5 volt ref signal to it then you replaced the wrong part. You need to replace the coolant temperature sending unit.  The coolant temp "sensor" is an input to the ECM for your fuel injection system. The coolant temp "sending unit" is for coolant temp reading at the gauge, It is an NTC switch (negative temperature coefficient) which means as temp increases/resistance decreases. 

Dec 19, 2008 | 2001 Jeep Grand Cherokee

1 Answer

1991 toyota pickup fuel and temp gauges dont work


You might have a bad ground. According to my Haynes manual's wiring diagram, both gauges share the same ground and typically that is "located on the left side of the instrument panel", wherever that is. Sorry I can't be more specific about the location. While it may not be true on your vehicle (the wiring diagram states "typical late model" in its description), my wiring diagram says that the ground wire is Brown (BR). You might try locating that wire and track it to its attachment point. You also might try tapping into it and using a continuity tester and ground out the wire to metal (there's plenty of grounding points under there). Make sure the ignition key is off!! There might be a bad ground wire closer to the meters than the attachment point. Hope this is helpful. Allow plenty of time if you're going to investigate this yourself. Do you have other gauges? Do they work? I think that all of the gauges are ganged through the same fuse (but not through the same ground wire). You might consider checking the fuse to ensure that it's OK. Your owners manual that came with the truck will tell you which fuse is it. If there are other things on the same fuse and they work, it's not the fuse. I hope that this is helpful.

Oct 04, 2008 | 1991 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...