Question about Cars & Trucks

1 Answer

Suzuki 2005 650dr crankshaft bearing

Show picture

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 79,865 Answers

We do not have any such diagrams or pictures. Sorry If you wan to access the factory service manuals which do contain this info go here:

Posted on Nov 01, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need torque sequence for main saddle bolts . 22 in total for a 2012 chevy Cruze ecotek 1.4l turbo

Special Tools
  • EN-235-6 Installer
  • EN-470-B Angular Torque Wrench
  • EN-658-1 Installer
For equivalent regional tools, refer to Special Tools.

  1. Install a NEW crankshaft position sensor reluctor ring?(1) and the 3?bolts?(2).
  2. Tighten the 3?bolts?(2) to 10?Y?(89?lb?in).
  3. Lubricate crankshaft, crankshaft bearings and crankshaft bearing cap tie plate with engine oil.

  4. Install the 4?upper crankshaft bearings?(2) and the crankshaft thrust bearing?(3).
  5. Install the crankshaft?(1).

  6. Note: The thickness of the sealing bead should be 2?mm?(0.0787?in).
  7. Apply sealing compound?(1) to the outer rim of the groove on the crankshaft bearing cap tie plate. Refer to Adhesives, Fluids, Lubricants, and Sealers.

  8. Note: The complete installation procedure should not take longer than 10?minutes.
  9. Install the 4?lower crankshaft bearings?(3) and the lower crankshaft thrust bearing?(4).
  10. Install the crankshaft bearing cap tie plate?(2).
  11. Note: Do not reuse the old bolts.
  12. Install the 10?NEW inner crankshaft bearing cap tie plate bolts?(1).

  13. Caution: Refer to Fastener Caution. Caution: Refer to Torque-to-Yield Fastener Caution.
  14. Tighten the 10?inner crankshaft bearing cap tie plate bolts in the sequence shown and to the following specifications:
    1. Tighten the inner crankshaft bearing cap tie plate bolts to 25?Y?(18?lb?ft).
    2. Tighten the inner crankshaft bearing cap tie plate bolts an additional 60?degrees, using the EN-470-B wrench.
    3. Tighten the inner crankshaft bearing cap tie plate bolts an additional 15?degrees, using the EN-470-B wrench.

    Note: Do not reuse the old bolts.
  15. Install the 12?NEW outer crankshaft bearing cap tie plate bolts?(1) and tighten to the following specification:
    1. Tighten the outer crankshaft bearing cap tie plate bolts to 10?Y?(89?lb?in).
    2. Tighten the outer crankshaft bearing cap tie plate bolts an additional 60?degrees, using the EN-470-B wrench.
    3. Tighten the outer crankshaft bearing cap tie plate bolts an additional 15?degrees, using the EN-470-B wrench.

  16. Install the crankshaft position sensor?(1) and a NEW crankshaft position sensor seal ring?(2).
  17. Install the crankshaft position sensor bolt?(3) and tighten to 8?Y?(71?lb?in).

  18. Note: Lubricate the crankshaft rear oil seal.
  19. Install the crankshaft rear oil seal?(1) with EN-235-6 installer?(2).

  20. Use EN-658-1 installer?(1) to strike the crankshaft rear oil seal.

  21. My database showed this info. Only the inner 10 showed a sequence. The outer 12 didn't.

Feb 02, 2018 | Chevrolet Cruze Cars & Trucks

1 Answer

P0017 on a 2007 suzuki xl7

did you look it up? shows.
it means the engine needs service and inspections here.

Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor "B"
Number of Trips to Set Code: 2
Trouble Code Conditions:
Difference between camshaft (bank 1 / exhaust side) position and crankshaft position is out of specified range.
Possible Causes:
  • CMP sensor
  • CKP sensor
  • Signal rotor
  • Timing chain
  • Timing chain tensioner
  • CMP actuator
  • ECM

Feb 24, 2014 | 2007 Suzuki XL-7

1 Answer

Crankshaft sensor

It looks like its on the side of the block, and easy to get to. one bolt holds it in, and it pulls right out. Here is a diagram of its locaton:5e07fd6f-45ba-4748-b950-40df5322281c.jpg

and here is a picture of a new one, as it will show you better what your looking for.:

Just unplug it, take out the 1 bolt, and replace. 94.99 at my autozone store tho. OUCH. sorry about the price.

Dec 06, 2013 | Suzuki Cars & Trucks

2 Answers

Engine connecting rod torque specification.

contact autozone or dealer service for specs..

Feb 09, 2013 | 2005 Suzuki Forenza

1 Answer

1992 4x4 front wheel bearing adjustment

To follow the "specs" you need a special socket with four pins (google should find a picture) to torque the bearing nut. These are crush bearings and are designed to be tighter than the older style bearings.
The bearing nut is under the locking hub, behind the locking washer that is fastened down with four screws.

Mar 27, 2012 | Suzuki Vitara Cars & Trucks

1 Answer

Need to know where the crank sensor is located on a 08 suzuki xl7 awd 7 passenger 3.6 v6

It's on the side of the block (marked 6), near the rear as seen in the picture of your engine below.. It picks up its signal directly off the crankshaft throw.


Jun 10, 2011 | 2002 Suzuki XL-7

2 Answers

Need to repair the main bearing on a suzuki vitara you have any diagrams or guidelines and if not where can i find them

The main bearing is apart of the lower part of the engine you have to remove the engine dissemble check everything ensure its within specs have it machined replace what is bad ensure its within spec and reinstall. You can go to autozone and get a copy of alldata for the vehicle for 15 bucks which includes all information needed.

Nov 29, 2010 | 1999 Suzuki Vitara

1 Answer

How to remove lower bearing on connecting rod in a yamaha yz125.

I'm not 100% sure because I have'nt had much dealings with yamaha dirtbikes but I do know that on Hondas and Kawasakis there are no rod caps to remove the rod from the crank, the crankshaft actually splits and the rod slips off. They are a very tight press fit and have to be reassemled perfectly or it will throw the whole balance of the engine off. I recommend taking it to the dealer and letting them do it. I know that on my Honda CR 125 instead of trying to replace the lower rod bearing I was able to purchase a crankshaft with a new rod already attached. Hope this was helpful.

Jul 25, 2009 | Suzuki Aerio Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides