Question about Audi Cars & Trucks

1 Answer

Abs light comes on at 60mph aprox - Audi Cars & Trucks

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert that has over 500 points.


    An expert whose answer got voted for 20 times.

  • Expert
  • 180 Answers

Could have a wheel speed sensor going bad but you need a ABS computer hooked to vehicle to tell you which one.

Posted on Nov 01, 2012


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 4044 Answers

SOURCE: The ABS break trouble light will come for aprox 8

Check for loose wires to the ABS module and have the module checked. This could be a bad Caliper but it sounds like it is the ABS module malfunctioning.

Posted on Oct 08, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Vehicles front end vibates at 60mph

Your car need wheel aligment most dhops charge aprox. $50.00

Sep 09, 2012 | 2002 Mitsubishi Galant

1 Answer

Gear shift stays in park and abs esp and asr lights on

1) try to use the self diagnose.
2) place ignition swtuch in the start position, the lights coming on
3) engine starts, the brake light sould turn off inmediately. the ABS ligth will illuminate for aprox 6 seconds.
4) test drive the vehicle at speed above 20mph for a few minutes. during the test the both test lights should remain off, if any one of the warninign light utron, take note of the condition.
5) stop the vechicle using the braking pressure.both light should remain offf during the stopping procedure.
60 place the gear selector in to PARK, and observe the warning lights, they should both be off.
God bless you

Jul 09, 2012 | Cars & Trucks

1 Answer

The ABS break trouble light will come for aprox 8 starts then all will be fine for aprox 20 starts then repeat

Check for loose wires to the ABS module and have the module checked. This could be a bad Caliper but it sounds like it is the ABS module malfunctioning.

Oct 07, 2011 | 1998 Oldsmobile Aurora

1 Answer

ABS warning light remains on in my car from the last few days. It initially used to come on when i drove on the motorway and exceeded 60mph, but now it always remains on even if i drive at 5mph..what could...

Have them check the wheel bearing first, the ABS sprocket is on the inside of the wheel part of the wheel bearing assembly and the sensor is there to.It would be a early warning for a wheel bearing problem.

Feb 24, 2011 | 2000 Hyundai Accent

2 Answers

Want to know if i have front or rear abs

Look under the hood at the master cylinder. If you see only two hydraulic lines coming out of one side or the other, it's NON-ABS.
ABS master cylinder has several....
Or you COULD get into a deserted parking lot, get to aprox 30mph, jam and hold the brake pedal and see if it "vibrates" or "pulsates"

Feb 02, 2010 | 2006 Dodge Ram 1500

1 Answer

1992 buick park avenue

try that, can't remember if ABS codes copme through OBD diagnostic connector, worth a try

Mar 19, 2009 | 1991 Buick Park Avenue

3 Answers

ABS/Brake Light on GMC Envoy Dash

Might save you a whole lot of time if you stop by autozone, or Pep Boys, and get the free scan & see which sensor may be faulty, or sending code. I've had mine trip from driving in nasty weather for a while before, and a trip to the carwash, and concentrating the sensor areas with spray, (back of wheels area) put light back out, next start.

Mar 12, 2009 | 2002 GMC Envoy

3 Answers

Jaguar dsc fault

DSC is your dynamic stability control, you probably went over something really hard and caused a fault, this is a normal response. If the fault stays on disconnect the battery and leave for five mins then reconnect, if you still have the same robelem your DSC module is faulty, it is located on the rear axel it is a block with an arm connected to the axel mid way on the axel.
Has nothing to do with yor abs the juddering was probably you driving over something which triggered the fault.
hope this helps

Dec 27, 2008 | 2002 Jaguar X-Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers


Level 3 Expert

76691 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14381 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides