Question about Chevrolet Cars & Trucks

Open Question

Code co775 low tire pressure system not learned on a 2007 silverado 6.0

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
SUL827
  • 93 Answers

SOURCE: Nissan 2007 Frontier tire pressure monitoring system

You need to set all the pressures to 35 psi. first then drive for approx.1/4 mile. If this doesn't work to reset the light (keep in mind the code itself will still be stored even though the light goes off) you will need to take it to your Nissan Dealer to have it scanned as there may be a malfunction with the sensor. If faulty and you are under 36k miles then it should be covered under your factory warranty. Hope this helps.

Posted on Oct 17, 2008

Ad
  • 1 Answer

SOURCE: how do I reset the

The answer to the suzuki guys questions. Press and hold the lock and unlock buttons at the same time on your little clicker that arms the car. The blinker lights should both come on at the same time and the car should honk to. This should reset the tpms.

Posted on Nov 11, 2008

  • 1 Answer

SOURCE: low tire pressure warning light stays on

I brought my RX350 to the dealer for this problem before. They told me to inflate my tires to 36psi for winter time although the recommended pressure is 30 psi

Posted on Jan 18, 2009

  • 840 Answers

SOURCE: 2007 grand prix tire pressure monitor reset

After you adjust the tire presuure you must drive the vehicle for a few miles then look at the gage again/ you can also disconnect battery for 15-20 minutes. Please rate my response Thank you very much

Posted on Jan 28, 2009

  • 1 Answer

SOURCE: How do you reset a low tire pressure warning on a 2008 Jetta?

Reset the tire pressure warning, same as you would any service issue. Insert key in ignition, hold wrench button and min button, then start engine.

Posted on Jun 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Help with learn mode.How to? sorry,it's a 2007 versa sl hatchback,not a sentra.


To activate a new transmitter in the tire pressure monitoring system WITHOUT the Nissan Consult scan tool: Under the dash above the OBD II connector is a single wire connector called the "tire pressure warning check connector". Use a jumper wire and ground the tire pressure warning check connector with the key OFF. Then turn the key ON and cycle the ground at the tire pressure warning check connector 5 times within 10 seconds of turning the key ON. This should cause the tire pressure monitor light to start flashing indicating the system is in "learn mode". Then use the activation tool starting at the left front tire and work around the vehicle in a clockwise direction - front left, front right, rear right and rear left. Activating each transmitter at each wheel should make the turn signal flash one time and after completing all 4 wheels, the turn signals should flash two times and all 4 time pressures should be displayed.

Apr 07, 2015 | 2007 Nissan Sentra 2.0 SL Sedan

1 Answer

After i put air in tiers how to i make low tire pressure light go off in 2007 eddie bauer expedition el


Go to the "Discount Tire shop", and they will do it for you for free. Then learn how to spell. ??? air in tiers ???

Feb 24, 2015 | 2007 Ford Expedition Eddie Bauer EL

3 Answers

How do you reset the low tire pressure light?


To reset the tire pressure system, do the following:

(NOTE!....Do not reset the check tire pressure system without first
correcting the cause of the problem and checking
and adjusting the pressure in all four tires. If you reset
the system when the tire pressures are incorrect,
the check tire pressure system will not work properly
and may not alert you when a tire is low or high.)

1. With the engine off, turn the ignition to ON.
2. Press the MODE button until the DIC reads LOW
TIRE PRESSURE HOLD SET TO RESET.
3. Press and hold the SET button until you hear a
chime, and TIRE PRESSURE RESET is displayed.

You will hear three chimes, then the LOW TIRE
PRESSURE message will go off and the DIC will return
to TIRE PRESSURE NORMAL. If the LOW TIRE
PRESSURE message comes back on, the check tire
pressure system has not reset. Repeat the procedure.
The system completes the calibration process during
driving. The system learns the pressure at each tire
throughout the operating speed range of your vehicle.
The system normally takes between 30 and 60 minutes of
driving to learn the tire pressures. The system normally
takes 10 to 20 minutes of driving in each speed range to
learn tire pressures. The speed ranges are 20 to 40 mph
(32 to 64 km/h), 40 to 60 mph (64 to 96 km/h), and above
60 mph (96 km/h). This time may be longer depending on
your individual driving habits. The learning process does
not need to be completed during a single trip. Once
learned, the system will remember the tire pressure until
the system is reset.

Jun 02, 2014 | 2004 Buick Rendezvous

1 Answer

Programing tpms sensor 08 silverado


Hope this helps you.

LEARN MODE CANCELLATION
The TPM system will cancel the learn mode if more then 2 minutes have passed and no sensors have been learned, or if the system has been in learn mode for more than 5 minutes. If the learn mode is canceled before any sensor has been learned, the PDM will remember all current sensor IDs and their locations.

CAUTION: Before proceeding with the steps below, ensure that no other sensor learn procedure is being performed simultaneously, or that tire pressures are not being adjusted on a TPM equipped vehicle within close proximity.

STEP BY STEP:
  1. Turn "ON" the ignition, with the engine OFF.
  2. Apply the parking brake. IMPORTANT: If the learn mode cannot be enabled, ensure the TPM system is enabled in the PDM.
  3. Turn the exterior lamp switch from "OFF" to parking lamps 4 times within 4 seconds. A horn chirp will sound and the low tire pressure light will begin to flash indicating the learn mode has been enabled.
    CAUTION: Over inflating tires may cause personal injury or damage to the tires and wheels. When increasing tire pressure do not exceed the maximum inflation pressure as noted on the tire sidewall.
    IMPORTANT: If a horn chirp does not sound after 35 seconds for any of the 4 sensors, turn the ignition "OFF" to exit the learn mode and repeat the procedure from step 1.
  4. Starting with the left front tire, increase or decrease the pressure for 8-10 seconds, or until a horn chirp sounds. The horn chirp may occur before the 8-10 second pressure increase/decrease time period has been reached, or up to 30 seconds after the 8-10 second pressure increase/decrease time period has been reached.
  5. After the horn chirp has sounded, proceed as in step 4 for the next 3 sensors in the following order:

    Right front
    Right rear
    Left rear
  6. After all sensors have been learned, exit the learn mode by turning "OFF" the ignition.
  7. After the learn mode has been exited, adjust all tire pressures to the recommended psi
  8. After adjusting all tire pressures to the recommended psi, run the tire pressure check in the DIC to see that the correct pressure is listed.

Oct 31, 2012 | Cars & Trucks

3 Answers

My low tire light came on so I went and had air and all the tires checked but now I don't know how to turn the light off. I have had the car since 2000 and it has 50,000 miles on it but could never figure...


Hello Mattingly.

Here is some information for you regarding your problem.

The Tire Inflation Monitor (TIM) system alerts the driver when the pressure changes in one of the tires. The system only detects a low pressure condition while the vehicle is being driven. Once a low tire pressure condition is detected, the system informs the driver that a low tire pressure condition exist's, whenever the ignition is ON.
The LOW TIRE message appears on the Instrument panel if the tire pressure in one tire becomes at least 82 kPa (12 psi) lower or higher than the other three tires. The message does not appear if more than one tire is low or high, or if the system is not calibrated properly. The system does not inform the driver which tire is low. To clear this message, set the tire pressures in all four tires to the proper pressures and perform the system reset procedure. Refer to Tire Inflation Monitor Reset Procedure for service procedure.
The Tire Inflation Monitor software requires approximately one half hour of straight line driving to complete the TIM autolearn. There are several speed ranges that the EBCM needs to learn the tire inflation configuration in order to have the full capability of detecting a low tire condition. The speed detection ranges are the following:

  • 24-64 km/h (15-40 mph)
  • 64-113 km/h (40-70 mph)
  • 113-145 km/h (70-90 mph)
Each speed range has 2 modes of low tire detection.

  • Monitor Mode 1
  • Monitor Mode 2 The EBCM learns the tire inflation configuration for each speed range independently. In Monitor Mode 1, the EBCM has only partially learned the tire inflation configuration for the speed range and has limited detection capability for a low tire condition. In Monitor Mode 2, the EBCM has fully learned the tire inflation configuration for the speed range and has full detection capability for a low tire condition. If the EBCM is not in Monitor Mode 1 or Monitor Mode 2, a low tire condition cannot be detected because the EBCM has not learned the tire inflation configuration of the vehicle.

To reset (calibrate) the system:
Turn the ignition switch to RUN. Then press and hold the RESET button for about five seconds. The red RESET button is located inside the instrument panel fuse block on the right side of the dash.. The LOW TIRE light will come on and flash three times and then it will turn off.
The system completes the calibration process during driving.
The system normally takes 15 to 20 minutes of driving in each of three speed ranges to "learn" tire pressures. The speed rages are 15 to 40 mph (25 to 65 km/h), 40 to 65 mph (65 to 105 km/h) and above 65 mph (105 km/h).

There you are, this should fix you up.
Keep in mind this system uses wheel speed sensors to calculate. If one of your sensors isn't working your low tire light will remain on.

Thank you for using FixYa.

KL

Jan 20, 2011 | 2000 Buick Century

2 Answers

Hi, I have a check front tire pressure warning on my 2009 saturn vue hybrid I filled up the tire it's not low at all, how do I get rid of the indicator warning? Thanks Amanda


The TPMS light (Tire Pressure Monitoring System) for that vehicle should function as follows.

If the light is on and steady, it means that the pressure in one or more of the tires is too low, and if the light is flashing, then it indicates that one or more of the tires are over-inflated.

1. Turn the ignition key to the "On" or "Run" position but do not start the vehicle. (If the vehicle has an electronic keyless ignition then place the ignition switch in the "ACCY" position)

2. Press the "Lock" and "Unlock" buttons at the same time on the vehicles remote key fob, and keep holding the two buttons down until you hear the horn beep, and usually this takes around five seconds. The horn beep will indicate that the learn cycle has begun.

3. Re-learn the TPMS system. Deflate or inflate air into the driver-side front tire for approximately 8 to 10 seconds and then listen for the horn to beep one time. (the horn might beep before the 8 to 10 second re-learn, or it could even take as long as 30 seconds after)

4. Repeat steps 2 and 3 for the remaining three tires. Also, the remaining three tires must be checked in the exact following order, the passenger-side front tire, the passenger-side rear tire and finally the driver-side rear tire. After the final TPMS sensor has re-learned then the horn will beep twice.

5. Listen for the horn to beep twice. When the horn does beep twice, it wikll be the indicator that the TPMS system has re-learned and reset.

6. Turn the ignition switch to the "Off" position, and then be certain that all four tires have the correct tire pressure as recommended on the drivers door, and the next time that the ignition is turned on, the tire pressure light should be reset.

Let me know if you require any further assistance.

Sep 23, 2010 | 2009 Saturn VUE

3 Answers

Reset Tire Pressure Sensor on 2007 Dodge Caliber


Hello
Welcome, If you have driven over a month and it has not reset there is a problom with one of the 4 sensors, You will need to have the TPMS scaned to see witch sensor is not working,, Here is a link explainin this in detail
http://www.chryslertpms.com/

Jul 14, 2010 | 2008 Dodge Caliber

1 Answer

Tire pressure monitoring system 2007 Chevy 2500HD


There is a Fuse that is labeled (hzd, or Hazard ) remove it for 15 sec. and return to position it should reset the whole system then check and see if it goes back to original operation good luck

Apr 03, 2010 | 2007 Chevrolet Silverado 2500HD

1 Answer

Resetting the tire pressure indicator on a chevy


Typically a tire pressure monitoring system uses an indirect measurement, and only measures the differences between the pressure in all of your tires. It does this by monitoring the speed at which the wheels are rotating. If one of the tires has low pressure, it will have to spin faster than the others, because the tire is partially flat, and the diameter of the tire is smaller.
If you are running different tire pressures in the front and back tires, then it might trigger the light to come on.
This might also be due to uneven tire wear or different size tires on the front and back.
Check the tire wear, and temporarily run equal tire pressure in the front and rear. It might take a few miles for the light to reset, so give it some time.

Dec 30, 2009 | 2007 Chevrolet Silverado 2500HD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

275 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...