Question about 1995 Pontiac Sunfire

3 Answers

How to remove clutch slave cylinder on a 95 sunfire

Do i have to pull the tranny?

Posted by on


3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

No you dont have to pull the tranny to get to the slave should be located on the drivers side almost under the door or right in front of the door, at least thats where mine was at

Posted on Jan 03, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert that has over 500 points.


    An expert whose answer got voted for 20 times.

  • Expert
  • 152 Answers

Yes, looks to be that way. this link will give you more info. hope this helps,1990501/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c1528003d036

Posted on Jan 03, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Where is slave cylinder on 1996 pontiac sunfire

Posted on Apr 09, 2011

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My friend had clutch replaced 6 mths oago and now clutch is not engaging is there anyway to check hydraulics without removing tranny?

Check clutch fluid level in clutch master cylinder for proper level. You can also watch the slave cylinder move at the transmission where it pushes on the clutch fork. The slave cylinder should move when the clutch pedal is depressed. If the cylinder does not move, suspect a defective master cylinder/slave cylinder/air in system that will require bleeding. If all moves, suspect tranny removal for inspection

Feb 22, 2016 | Cars & Trucks

2 Answers

I have a 95 jeep wrangler yj 2.5L that the clutch is bleeding off. I bought new clutch master cylinder for it but is different than the one I took off which come to find out was the wrong one somebody else...

if there is no slave there, than its coax. see 95 Ax5/15 box photo below. "called COncentric by jeep" or sandwiched by us.
first replace the MC, bleed it, and test.

if that dont fix the clutch, then the coax is bad.
you never stated symptom/s. (lost fluid? there are 15 clutch symptoms) ive done them all, and blown many racing so......
if the coax is bad, you must pull the tranny

see item in red, took me 10 hrs labor to do mine, so....
my new wrangler is external not by accident....


Jan 29, 2015 | Jeep Cars & Trucks

2 Answers

It is difficult to put into gear from a stop and while downshifting. 2000 mustang V6

check gear fluid in the tranny, brake fluid in the clutch master cylinder. after that check slave cylinder and linkage

Jul 30, 2010 | Ford Mustang Cars & Trucks

3 Answers

Im having to add break fluid for my clutch daily on jeep wrangler

Check around the slave valve under the car on the tranny.
There is only 3 places it could leak
The clutch master cylinder
the pipe from the master cylinder to the slave valve
or the slave valve.

Dec 22, 2009 | Jeep Wrangler Cars & Trucks

2 Answers

Hydraulic or ? ? ?

Its hydraulic and it sounds like a bad clutch master cylinder or even the slave cylinder. Good luck

Dec 08, 2009 | 1993 Jeep Wrangler

3 Answers

Fork engaging slave cylinder from tranny. (91 3000GT, mitsu)

Called a clutch fork Holds the thrust bearing right? and goes through the clutch (Bell) housing Got to be careful here or Is it the rod that goes directly into the slave cylinder? Either way as long as the rest of the cars ok it's worth keeping If it's the clutch fork you going to have to remove gearbox (Not the end of the world) Part won't be that expensive

Oct 22, 2009 | 1991 Mitsubishi 3000GT

3 Answers

Clutch will not engage.

You have to bleed the system again they can be a pain in the b@TT, also get a second person to operate the clutch and watch to see if the lever moves, if it does pull off the rubber and make sure you have the Y on the pivot ball inside the transmission. And if you don't get enough throw adjust the clutch rod on the clutch pedal by removing the pin and loosen the lock nut and make it longer by unscrewing the shaft. You want a half inch of free play at the top of the pedal the you want the clutch to catch about 3/4 of the way down. Also if you try to put it in gear does it grind the gears? Also did you put the clutch plate in backwards this is a common mistake even for a pro who gets interrupted by a phone call or a good-looking gal walking by, if ya need more suggestions let me know by posting to this comment.

Aug 20, 2009 | 1991 Ford Ranger Supercab

1 Answer

1999 pontiac sunfire bleeding clutch

my 1999 pontiac sunfire drivers door latch is broke can not close the door. i have it pulled shut? how much will a used latch cost, or even 3 bolts for it? all the auto stores/ jumk yards are closed for me to call

Jan 26, 2009 | 2003 Pontiac Sunfire

1 Answer


The slave is an internal type and is located inside the tranny bellhousing. You will need to pull the tranny to access it.
The reservoir should be on the driver's side firewall in the engine compartment.
The fluid level being low could also cause the problem. If it is low you may have to bleed the clutch line.
Check to see if there is fluid leaking from the bellhousing, as that is an indicator of a bad slave cylinder. If you have to replace the slave cylinder, it is a good idea to replace the clutch while you have the tranny out.

Dec 23, 2008 | 2000 Ford Ranger SuperCab

1 Answer

Slave cylinder or clutch? or both?

it internal and pretty much alot of work. You have to pull the transmission out

Jul 24, 2008 | 1995 Pontiac Sunfire

Not finding what you are looking for?
1995 Pontiac Sunfire Logo

Related Topics:

1,210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8825 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides