Question about Renault Cars & Trucks

1 Answer

Does a 2005 have a timing sensor in the flywheel

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,101 Answers

Yes depends on the car or truck,and it is call a crank position sensor

Posted on Oct 31, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I locate the Crank shaft sensor on a 2005 Dodge Durango

Have you looked on the transmission just behind the engine block? A lot of the Dodge vehicles get readings of the flexplate/flywheel.

Sep 12, 2014 | 2005 Dodge Durango

1 Answer

Timing marks for CRANK SHAFT ON 2005 jaguar XJ

there is no marks the ign timing is ecu controlled a locking device goes in the flywheel housing where the crank sensor fits to time the valve timing and locking bars fit over the camshafts.sounds

Feb 01, 2014 | 2005 Jaguar XJ-Series

1 Answer

2005 ford f150 king ranch changed fly wheel now it wont start

Did it start before?

Who did the flywheel?

Is the crank sensor still there?

Is the flywheel the correct one,that is where
the crank signal comes from ?

Dec 14, 2012 | Cars & Trucks

2 Answers

Crank position sensor is hitting flywheel flywheel got damaged somehow can I bend it down with out a problem or is a new one a must need

What type of car is this..but to answer your question the flywheel would have to be out of round to make contact with the crank sensor i suspect you have a cracked or broken flywheel most of the time they will break at the center of the flywheel where the crankshaft attaches to the flywheel and would still drive for some time

Dec 10, 2012 | Cars & Trucks

1 Answer

Where is the crank shaft sensor on a 2006 kia optima

Hi LIsa:
On 2001-2005 vehicles the crankshaft sensor is mounted on the front of the transmission case adjacent to the flywheel.

On 2006 vehicles the crankshaft position sensor is located next to the radiator hose inlet and outlet assembly.

I really hope this helps, and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Have a nice day and thanks for using FixYa.


Oct 16, 2011 | 2006 Kia Optima

1 Answer

Where is the crank sensor on 2005 320d bmw and what do you have to remove to change it ?

To get to the crank sensor on a 320d you need to remove intake manifold then the starter you will then find a plug and a small 5mm allen key bolt angled toward the flywheel losen that and that is the crank sensor.

Apr 05, 2011 | 2005 BMW M3

1 Answer

How do u separate two piece flywheel

Thats your starter ring that you need to remove its a press fit so start by supporting the flywheel with some wooden blocks and then heat your starter ring with a torch so it will expand and can then be driven off with a hammer and drift punch.
To install the new starter ring you will need to use your wifes oven set at 450 degrees to heat the new starter ring for about 20 mins so it will expand and put the flywheel in the fridge at the same time so it will contract, have your hammer and drift punch ready so you can seat the starter ring on the flywheel before it cools down. P.S. Use oven mitts so you won't get burned!

Jun 17, 2009 | 2005 Jeep Wrangler

1 Answer

Crank sensor 2001 kia rio

On 2001-2005 vehicles the crankshaft sensor is mounted on the front of the transmission case adjacent to the flywheel.

Please rate and god bless:)

May 13, 2009 | 2001 Kia Rio

1 Answer

Timing sensor location

Two sensor (takes place of distributor) and one (crank sensor) on left side of bellhousing even with flywheel. If it's a 4.0....May be similar arrangement on other engines but I don'tknow for sure!

Feb 20, 2009 | 2005 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

xxxxxx xxx

Level 3 Expert

4917 Answers


Level 3 Expert

78267 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides