Question about Cars & Trucks

1 Answer

Does the 2005 have a timing sensor in the fly wheel

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,381 Answers

2005 WHAT.

Posted on Oct 31, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crank sensor location


dear .its in between engine and transmission . direct to fly wheel

Oct 26, 2013 | 2005 Skoda Fabia 1.4

1 Answer

2005 ford f150 king ranch changed fly wheel now it wont start


Did it start before?

Who did the flywheel?

Is the crank sensor still there?

Is the flywheel the correct one,that is where
the crank signal comes from ?

Dec 14, 2012 | Cars & Trucks

1 Answer

2005 optima ckankshaft sensor


2005 optima cranksensor if you are a 2.4 the CKP sensor is located at front of crankshaft,behind the timing belt cover. If your engine is running rough or stalling try shaking the sensor connector to see if it affects engine operation. Inspect the male to female terminal for proper fit. If you are a 2.7 the CKP sensor is mounted on left side of engine block, near the fly wheel. For either engine size if you are cranking the engine and your tach reads zero,you are dealing with a failed CKP.

Jan 10, 2012 | 2005 Kia Optima LX

1 Answer

I replaced my flywheel and clutch on my v6 altima, I now have codes for camsharft angle.


I hate to tell you this, but you will have to take the trans out again and put the fly wheel into the right spot. there is a dowel that keeps it in the right spot. that fly wheel if keyed to the crank shaft. It is very important to make sure that you put it back the same way you took it off and it is very easy to put it on the wrong way/wrong spot if you are not paying attention.It will go back together just fine, but the actual fly wheel it self is in the wrong spot on the back of the crank causing the cam angle sensors codes. Trust me i have seen it done. You dont have the flywheel in the right spot on the back of the crank 100% guaranteed solution. Been doing this with Nissan for about 16years. Good luck.

Nov 18, 2010 | 2005 Nissan Altima

1 Answer

4x4 on my 2005 f150 will not ingage


Is the system ESOF ( Electronic Shift On the Fly ) or MSOF ( Mechanical Shift On the Fly ) ? Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc ). Key on, engage 4x4 and try to turn the front drive shaft. If it turns it is a problem with the transfer case. If it doesn't it is a front axle engagement problem.

Mar 12, 2010 | 2005 Ford F-150

1 Answer

98 f-150 4x4 ,when you turn 4x4 sw ,relay in dash clicks about 6 time ,but no 4x4 light in dash and it don't lock in


Is the system ESOF ( Electronic Shift On the Fly ) or MSOF ( Mechanical Shift On the Fly ) ? Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc ). Key on, engage 4x4 and try to turn the front drive shaft. If it turns it is a problem with the transfer case. If it doesn't it is a front axle engagement problem.

Jan 20, 2010 | 2005 Ford F-150

1 Answer

2005 Sierra 4wd is not working properly


we ended up taking it to the dealership, it was a sensor.

Jan 28, 2009 | 2005 GMC Sierra

2 Answers

Fly wheel problem on a jeep


if its a 4JX1 diesel, yes it goes in 1 spot yet it can be bolted up in every location
put crank pulley timing mark to TDC can also check by removing cam belt top cover and check timing mark aligned up with mark at 12 O clock then flywheel has small notch in edge that must go at 6 O clock (facing down) look closely it is hard to see due to flywheel sunk into back of block.

Oct 19, 2008 | 2000 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...