Question about Cars & Trucks

1 Answer

Programing tpms sensor 08 silverado - Cars & Trucks

Posted by on

  • Drew Oct 31, 2012

    i have replaced the sensor in the wheel the dealer wants to bend me over to program since i did get there sensor for 100 bucks

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 206 Answers

Hope this helps you.

LEARN MODE CANCELLATION
The TPM system will cancel the learn mode if more then 2 minutes have passed and no sensors have been learned, or if the system has been in learn mode for more than 5 minutes. If the learn mode is canceled before any sensor has been learned, the PDM will remember all current sensor IDs and their locations.

CAUTION: Before proceeding with the steps below, ensure that no other sensor learn procedure is being performed simultaneously, or that tire pressures are not being adjusted on a TPM equipped vehicle within close proximity.

STEP BY STEP:

  1. Turn "ON" the ignition, with the engine OFF.
  2. Apply the parking brake. IMPORTANT: If the learn mode cannot be enabled, ensure the TPM system is enabled in the PDM.
  3. Turn the exterior lamp switch from "OFF" to parking lamps 4 times within 4 seconds. A horn chirp will sound and the low tire pressure light will begin to flash indicating the learn mode has been enabled.
    CAUTION: Over inflating tires may cause personal injury or damage to the tires and wheels. When increasing tire pressure do not exceed the maximum inflation pressure as noted on the tire sidewall.
    IMPORTANT: If a horn chirp does not sound after 35 seconds for any of the 4 sensors, turn the ignition "OFF" to exit the learn mode and repeat the procedure from step 1.
  4. Starting with the left front tire, increase or decrease the pressure for 8-10 seconds, or until a horn chirp sounds. The horn chirp may occur before the 8-10 second pressure increase/decrease time period has been reached, or up to 30 seconds after the 8-10 second pressure increase/decrease time period has been reached.
  5. After the horn chirp has sounded, proceed as in step 4 for the next 3 sensors in the following order:

    Right front
    Right rear
    Left rear
  6. After all sensors have been learned, exit the learn mode by turning "OFF" the ignition.
  7. After the learn mode has been exited, adjust all tire pressures to the recommended psi
  8. After adjusting all tire pressures to the recommended psi, run the tire pressure check in the DIC to see that the correct pressure is listed.

Posted on Oct 31, 2012

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7 Answers

SOURCE: tpms light on

your sensors may need to be re-initialized. Consult your local dealer. This will have to be performed with special equipment.

Posted on Feb 06, 2010

  • 7 Answers

SOURCE: i replaced my 08 accord wheels with an 09 accord wheels

thank your gorvernment. they required auto makers to implement some sort of tire pressure monitoring system in all vehicles. More than likely what needs to be done is a re-initialization of the sensors. it will most likely need to be performed by a dealer.

Posted on Feb 06, 2010

  • 295 Answers

SOURCE: any way to pull fuse on tpms. I just put

unfortunely not The system is monitered by the WCM (wireless control module). you would have to install the TPMS on the new wheel. You can just swap them from the other wheels you took off. use a 13mm deep socket remove the sensors and install on the wheel you have on the car. hope this helps.

Posted on Jul 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What could be problem.. We have VDO-Redi sensors VDO SE10001HP in 2 Lincoln Navigator 2008, but OEM learning proses wont regognize those. Both cars are working with original TPMS sensors.


Do you mean you failed an emission test? Then if that is the case you have not properly done an OBD2 drive cycle test. Google it for Ford.

Jun 24, 2016 | Lincoln Navigator Cars & Trucks

1 Answer

08 vw passat shakes when starting and tps light on


TPS = Throttle Position Sensor
TPMS = Tire Pressure Monitoring System

The TPS is located on the Engine and is part of the Intake System
The TPMS is located INSIDE the Wheel. If you changed the RIM or the Sensor that is normally located inside the wheel is missing, it would cause this. The Weird Noise? Is that an Out of Balance Tire?

We need more information to assist you.

Feb 12, 2014 | Volkswagen Cars & Trucks

1 Answer

I bought two rims with TPMS capability and put winter tires on them for my 2007 Honda Civic. I can not clear the TPMS light. I would think I would have to tell the TPMS that I have new/different rims on...


The new sensor I.D.'s will need to be programmed into the TPMS system. You could spend a couple of thousand dollars to get the tools to do this or call around some local shop or the dealer to see what the get for this. Then next summer you get to reprogram them again.

The other option is to pull 2 TPMS sensors out of your summer tires and install them into your winter wheels. Use a TPMS service kit to seal them up. You won't need to reprogram anything if you go this route.

The third option is not to worry about it. The old fashioned way of doing things was to check your tires every couple weeks for proper inflation. If you are in tune with the way your vehicle handles than you should be able to notice the change in the handling characteristics as a tire goes low. After all we survived for 100 years without TPMS.

Nov 05, 2010 | Honda Civic Cars & Trucks

1 Answer

Tpms light on


your sensors may need to be re-initialized. Consult your local dealer. This will have to be performed with special equipment.

Jan 13, 2010 | 2008 Honda Accord

1 Answer

I replaced my 08 accord wheels with an 09 accord wheels


thank your gorvernment. they required auto makers to implement some sort of tire pressure monitoring system in all vehicles. More than likely what needs to be done is a re-initialization of the sensors. it will most likely need to be performed by a dealer.

Jan 12, 2010 | 2008 Honda Accord

2 Answers

2007 yukon tpms keeps blinking to check tire pressure


The TPMS is a pain in the you know what. Have you changed tire sizes? There could be a bad sensor and may need replaced. We continually get problems all the time with the TPMS. We have reset then they reset again.

Sep 11, 2009 | 2004 GMC Yukon

2 Answers

How to reset the tire pressure on a 08' chevy tahoe?


TPMS Sensor Matching Procedure

Each TPMS sensor has a unique identification code. Any time you rotate your vehicle's tires or replace one or more of the TPMS sensors, the identification codes will need to be matched to the new tire/wheel position. The sensors are matched to the tire/wheel positions in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear tire using a TPMS diagnostic tool. See your dealer/retailer for service.

The TPMS sensors can also be matched to each tire/wheel position by increasing or decreasing the tire's air pressure. If increasing the tire's air pressure, do not exceed the maximum inflation pressure indicated on the tire's sidewall.

To decrease air-pressure out of a tire you can use the pointed end of the valve cap, a pencil-style air pressure gage, or a key.

You have two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer than two minutes, to match the first tire and wheel, or more than five minutes to match all four tire and wheel positions the matching process stops and you need to start over.

The TPMS sensor matching process is outlined below:

  1. Set the parking brake.
  2. Turn the ignition switch to ON/RUN with the engine off.
  3. Press the Remote Keyless Entry (RKE) transmitter's LOCK and UNLOCK buttons at the same time for approximately five seconds. The horn sounds twice to signal the receiver is in relearn mode and TIRE LEARNING ACTIVE message displays on the DIC screen.
  4. Start with the driver side front tire.
  5. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire's air pressure for five seconds, or until a horn chirp sounds. The horn chirp, which may take up to 30 seconds to sound, confirms that the sensor identification code has been matched to this tire and wheel position.
  6. Proceed to the passenger side front tire, and repeat the procedure in Step 5.
  7. Proceed to the passenger side rear tire, and repeat the procedure in Step 5.
  8. Proceed to the driver side rear tire, and repeat the procedure in Step 5. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.
  9. Turn the ignition switch to LOCK/OFF.
  10. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label.
  11. Put the valve caps back on the valve stems.

Jul 28, 2009 | 2008 Chevrolet Tahoe

1 Answer

TPMS indicator light on '08 honda accord lx


TPMS Tire Pressure Monitoring System

Check ALL including the spare tire for proper air pressure. If all is well then check the fuse for the TPMS module. If all is well there, off to the dealer you may have to go.

Jul 17, 2009 | Honda Accord Cars & Trucks

1 Answer

Any way to pull fuse on tpms. I just put


unfortunely not The system is monitered by the WCM (wireless control module). you would have to install the TPMS on the new wheel. You can just swap them from the other wheels you took off. use a 13mm deep socket remove the sensors and install on the wheel you have on the car. hope this helps.

Jul 09, 2009 | 2008 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...