Question about 2002 GMC Yukon XL

1 Answer

Replace wiper arm on 2002 gmc denali - 2002 GMC Yukon XL

Posted by on

  • Anonymous Mar 20, 2009

    Where is the tab. I can not find it sir?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

Down at the point where it Mounts and Swivels, There is a Small Tab that you need to Pull out. Then use Pliers with Tape Wrapped around to Remove Arm.

Posted on Jan 03, 2009

2 Suggested Answers

morganismo
  • 36 Answers

SOURCE: windshield wiper arm

These are a tight fit...Spray a little penetrating lubricant onto it and let it sit for about 20 minutes. You will notice there are splines that match up from the drive unit to the base of the wiper arm...sometimes these can get a little corroded and becasue of the relative surface area it makes them a real pain to get off. You may need to just pry against it gently with a flat head scredriver after you spray on the lubricant. Pray at it from all different sides of the base so that it doesn't bind up and get crooked.

Hope this helps! Good Luck!

Posted on Feb 12, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the wiper motor on a 2002 gmc sierra? Have used motor to replace it. May only be pulse board, but this was the advised solution.


I am assuming the truck is alot like my 2001 yukon. If that is the case, then the wiper motor is underneath the plastic cowl in front of the windshield. Mine was held on by 4 clips on the front and one screw on each side of the vehicle (driver/passenger). Wiper arms will need to be removed and will most likely need a wiper arm puller tool.

Dec 23, 2010 | 2002 GMC Sierra 1500

1 Answer

I have a 2002 gmc denali and Front wiper only works on high speed. Where should i look first? I have looked for fuses and they all appear fine.


I am having this same problem. Fuses are fine but the wipers only work on high speed. Did you get yours fixed?

Dec 05, 2010 | 2002 GMC Yukon Denali

1 Answer

Ride control light is on


There are height sensor at each wheel attached to the frame and control arm and rear diff areas. The sensor can break off and the ride light will come on. If thats not the problem you will have to get the codes read.

Nov 05, 2009 | 2002 GMC Yukon Denali

1 Answer

2002 gmc yukon denali ac pump


it has gone bad replace it

Aug 06, 2009 | 2002 GMC Yukon Denali

1 Answer

Remove wiper blade


Do you mean the wiper blade or the wiper arm?

The wiper blade should have a small tab or lever on the underside of the hinge where it attaches to the arm. Use a small screwdriver or a pick (etc..) to gently pry the lever upwards to pull the locking tab out of its corresponding hole on the wiper arm. Once the tab is up, firmly grasp the wiper blade and pull towards the base of the wiper arm. Sometimes they stick a little, just be careful not to bend the wiper arm.
If you are looking to remove the wiper arm, remove the plastic cap at the base of the wiper arm to gain access to the nut below. Using either a 13mm (1/2 inch) or 15mm socket (depending on the model) remove the nut by turning counter-clockwise. Once the nut is off, place your hand in the middle portion of the wiper arm and firmly push downward, being careful not to bend the arm. What you are trying to do is rock the arm off of the wiper motor stud. Be sure to mark where the wiper blade rests on the windshield before removing it, so you can reassemble it in the same spot when you put it back together. Use a grease pencil or something else that you can clean off later.
Hope this helps!

Mar 26, 2009 | 2006 GMC Yukon Denali

2 Answers

Wiper Linkage question...2002 Yukon Denali XL


BINGO you need to flip the wiper arm end cover up or off and tighten the nut, 13mm usually

your wiper arm just needs to be tightened up

but align them or it as you tighten it

Jan 27, 2009 | 2002 GMC Yukon Denali

Not finding what you are looking for?
2002 GMC Yukon XL Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...