Question about 1995 Mazda MX-6

Open Question

How to get mx 6 intake manifold off

1995 MX 6 LS V6 Intake Manifold removal- I am changing the valve cover gaskets because oil is leaking onto my spark plugs (causing white smoke from exhaust too). The first valve cover was simple and i could see the valve cover bolts but the INTAKE MANIFOLD, & THROTTEL is in the way of the rear valve cover! :( are there any diagrams/steps on How the Intake manifold is disconnected and throttle is safely removed ?

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mrgreenz
  • 962 Answers

SOURCE: 2001 mazda tribute spark plug change

can 't you remove the coils insted of the intake ? It is much easier.

Posted on Dec 02, 2008

Bigmick9
  • 18 Answers

SOURCE: valve cover gaskets, now it wont run

You need to get the timing checked, did you mark the position of the distributor before you took it off. If not you might be slightly off with the new distrib.

Posted on Sep 08, 2009

  • 1 Answer

SOURCE: how to remove the starter on mazda mx-6 gt

yes but you do have to pull the brace that connects to intake ,exaust ,an trans.

Posted on Mar 13, 2010

  • 60 Answers

SOURCE: I want to change the spark plugs in my 2001mazda tribute

See the tips section of my profile on Fixya. I have complete instructions on how to change the plugs and coils.

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

SHO. What will I have to remove to replace spark plugs and valve cover gaskets?


If it is a 6 cylinder engine you will probably need to remove the intake manifold to replace the rear valve cover gasket. If that's the case the intake manifold also has two hidden screws in the rear against the firewall as well as an EGR exhaust line that must be removed before the intake manifold will come off. I highly recommend you buy a haynes repair manual for your make/model and a flexible mirror-on-a-stick to use for dis-assembly. The spark plugs can be removed after the valve covers are removed (if the valve cover is leaking you will likely have oil pooled around the plugs anyway).

Dec 28, 2015 | 1998 Ford Taurus

1 Answer

What is the torque specs on intake 4.3 l v6 vortec


0900c1528008ee89.gif

To install:

  1. Clean all gasket surfaces completely.
  2. Install the intake manifold gaskets with the port blocking plates facing the rear of the engine. Factory gaskets should have the words "This Side Up" visible.
  3. Apply gasket sealer to the front and rear sealing surfaces of the engine block.
  4. Apply a 0.197 inch (5mm) bead of RTV sealer to the front and rear of the block. Extend the sealer approximately 1 / 2 -inch (13mm) onto the heads.
  5. Install the lower intake manifold.
  6. Apply sealer to the lower intake manifold bolts prior to installation.
  7. Install the bolts and tighten in sequence and in 3 steps as follows:
    1. First step to 26 inch lbs. (3 Nm).
    2. Second step to 106 inch lbs. (12 Nm).
    3. Final step to 11 ft. lbs. (15 Nm).

  8. If removed, install the alternator bracket bolt.
  9. Install the coolant by-pass hose.
  10. Install the EGR valve.
  11. Connect the upper radiator hose to the thermostat housing.
  12. Connect the heater hose to the lower intake manifold.
  13. Connect the fuel pressure and return lines to the lower intake manifold.
  14. Connect the wiring harnesses and brackets to the lower manifold.
  15. Install the throttle cable bracket, then attach the throttle cable and the cruise control cable (if equipped).
  16. Install the transmission oil level indicator and tube, if equipped.
  17. Install the EGR tube, clamp and bolt.
  18. Install the PCV valve and hose.
  19. Install the A/C compressor and bracket.
  20. Install the distributor.
  21. Install the upper intake manifold.
  22. Fill the cooling system.
  23. Connect the negative battery cable.
  24. Start the vehicle and check the ignition timing (not adjustable).
  25. Verify no oil, coolant, vacuum or fuel leaks.

    0900c1528008ee88.gif

  26. Install the intake manifold bolts and tighten them to 35 ft. lbs. (48 Nm) in the sequence shown.

May 09, 2011 | Chevrolet TrailBlazer Cars & Trucks

2 Answers

Need to replace the intake manifold


3.8L Engine (most common) Upper Intake Manifold To Remove:
  1. Drain the cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable.
    • Fuel injector sight shield.
    • Air cleaner intake duct.
    • Right spark plug wires from the ignition control module and reposition.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Fuel rail assembly.
    • Brake booster hose from the vacuum source manifold in the upper intake manifold.
    • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
    • Throttle body support bracket upper bolt.
  5. Disconnect the electrical connectors from the following:
    • EVAP purge solenoid
    • Throttle Position (T/P) sensor
    • Idle Air Control (IAC) valve
    • Manifold Absolute Pressure (MAP) sensor
    • Mass Air Flow (MAF) sensor
    • EVAP purge solenoid vacuum line from the throttle body.
    • Accelerator and the cruise control cables with the bracket from the throttle body.
  6. Remove or disconnect the following:
    • Upper intake manifold bolts and stud.
    • Clean the upper intake manifold bolt threads.
  7. Remove or disconnect the following:
    • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
    • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
  8. If the upper intake manifold is being replaced, remove the following:
    • Throttle body assembly.
    • Manifold Absolute Pressure (MAP) sensor.
    • Positive Crankcase Ventilation (PCV) valve.
    • Vacuum source manifold.
Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

To Install:
  1. If the manifold was replaced, install or connect the following:
    • Vacuum source manifold.
    • Positive Crankcase Ventilation (PCV) valve.
    • Manifold Absolute Pressure (MAP) sensor.
    • Throttle body assembly.
    • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
  2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
  3. Install or connect the following:
    • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
    • Accelerator and the cruise control cables with the bracket to the throttle body.
    • EVAP purge solenoid vacuum line to the throttle body.
  4. Connect the electrical connectors to the following:
    • Mass Air Flow (MAF) sensor
    • Manifold Absolute Pressure (MAP) sensor
    • Idle Air Control (IAC) valve
    • Throttle Position (T/P) sensor
    • EVAP purge solenoid
  5. Install or connect the following:
    • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
    • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
    • Brake booster hose to the vacuum source manifold.
    • Fuel rail assembly.
    • Right spark plug wires.
    • Air cleaner intake duct.
    • Fuel injector sight shield.
  6. Connect the negative battery cable.
  7. Fill the cooling system.
  8. Inspect for fluid or vacuum leaks.
Lower Intake Manifold (W/O Supercharger) To Remove:
  1. Remove or disconnect the following:
    • Upper intake manifold.
    • Generator brace.
    • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
    • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
    • Radiator inlet hose from the water outlet housing.
    • ECT sensor electrical connector.
    • Right upper engine mount strut bracket.
    • Generator brace bracket bolts.
    • Generator brace bracket.
    • Lower intake manifold bolts.
    • Lower intake manifold.
    • Lower intake manifold seals.
    • Lower intake manifold gaskets.
  2. If replacing the lower intake manifold, Remove or disconnect:
    • Water outlet housing bolt and stud
    • Water outlet housing
    • Gasket and the thermostat.
    • ECT sensor.
  3. Inspect the flatness of inlet flanges.
  4. Clean the intake manifold mating surfaces.
  5. Clean the intake manifold bolts and bolt holes of adhesive compound.
To Install:
  1. If removed, install the ECT sensor.
    • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
  2. If removed, install the thermostat, the gasket, and the water outlet housing.
  3. If removed, install the water outlet housing bolt and the stud.
    • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
  4. Install or connect the following:
    • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
    • Lower intake manifold seals.
    • Lower intake manifold.
    • Lower intake manifold bolts.
    NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
  5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

  6. Install or connect the following:
    • Generator brace bracket.
    • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
    • Right upper engine mount strut bracket.
    • ECT sensor electrical connector.
    • Radiator inlet hose to the water outlet housing.
    • EGR outlet pipe to the lower intake manifold.
    • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
    • Drive belt tensioner.
    • Generator brace.
    • Upper intake manifold.
  7. Inspect for leaks.
Lower Intake Manifold (W/ Supercharger) To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the supercharger.
  4. Remove the thermostat housing.
  5. Remove the EGR pipe at the intake manifold.
  6. Disconnect the electrical connection at the temperature sensor.
  7. Remove the intake manifold and gaskets.
NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:
  1. Clean the gasket sealing surfaces.
  2. Install the intake manifold gaskets.
  3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
  4. Install the electrical connector to the temperature sensor.
  5. Install the EGR pipe to the intake manifold.
  6. Install the thermostat housing.
  7. Install the supercharger.
  8. Fill the cooling system.
  9. Connect the negative battery cable.

Aug 05, 2010 | 1997 Pontiac Grand Prix

3 Answers

What would cause oil in coolant and leak near intake manifold?


Head gasket, if you have a V6 or a V8, can't tell which one is at fault, so both will might as well be changed.
If the leak near the maifold is oil, the valve cover gaskets are leaking.
When head gaskets are changed, all the necessary gaskets come in the gasket kit.

Apr 23, 2010 | 1997 Cadillac Catera

1 Answer

I have a 2002 cavaliry Z24. It has the 2.4 engine. It has a bad miss. The trouble code that was givrn was po302. I have replaced the spark plugs and wires. I was wondering if there is a way to test the...


P0302 is random misfire on cylinder #2.

Most comment cause is vacuum leak at the intake manifold and vacuum hose.

If you valve cover is leaking oil on then DO THE HOLD JOB.

Remove valve cover to gain access the intake manifold.

Change the intake gasket and valve cover gasket.

Dec 12, 2009 | 1996 Chevrolet Cavalier

2 Answers

Ihave a small coolant leak looks like intake manifold just under valve cover how do i fix this


most likely the intake manifold gasket will need replacement. but find out exactly where the leak is first.

Oct 10, 2009 | 1995 GMC Yukon

1 Answer

Valve cover gaskets, now it wont run


You need to get the timing checked, did you mark the position of the distributor before you took it off. If not you might be slightly off with the new distrib.

Sep 08, 2009 | 1993 Mazda MX-6

1 Answer

I need a diagram of a 1995 ford escort engine


96 escort 1.9L

bb97132.gif
e0d7524.gif

Engine Components
Item Part Number Description 1 6766 Oil Filler Cap 2 6A548 (8 Req'd) Valve Cover Bolt 3 6582 Valve Cover 4 — Exhaust Manifold Shield-to-Exhaust Manifold Nut (4 Req'd) 5 9A462 Exhaust Manifold Shield 6 — Exhaust Manifold Shield Stud (4 Req'd) 7 9430 Exhaust Manifold 8 9454 Exhaust Manifold Nut 9 9448 Exhaust Manifold Gasket 10 — Exhaust Manifold Stud (Fine Thread), Short (4 Req'd) 11 — Exhaust Manifold Stud, Long (1 Req'd) 12 — Exhaust Manifold Stud (Medium Thread), Short (1 Req'd) 13 6518 Valve Spring Retainer Key 14 6514 Valve Spring Retainer 15 6513 Valve Spring and Damper, Intake 16 6C515 Valve Tappet Guide Plate Retainer 17 6571 Valve Stem Seal 18 6513 Valve Spring, Exhaust 19 12405 Spark Plug 20 6269 Camshaft Thrust Plate 21 — Camshaft Thrust Plate Bolt (2 Req'd) 22 — Cup Plug 23 6B273 Camshaft Oil Flow Control Rod 24 6K292 Camshaft Front Seal 25 6256 Camshaft Sprocket 26 6278 Camshaft Sprocket Washer 27 6K252 Camshaft Sprocket Retaining Bolt 28 6L269 Camshaft Sprocket Key (5 x 18) 29 6250 Camshaft 30 6051 Head Gasket 31 6A008 Cylinder Head to Block Dowel 32 6010 Cylinder Block 33 6507 Intake Valve 34 6505 Exhaust Valve 35 6049 Cylinder Head 36 — Intake Manifold Stud (7 Req'd) 37 17A084 Engine Lifting Eye 38 — Engine Lifting Eye Bolt (2 Req'd) 39 9439 Intake Manifold Gasket 40 — Bolt 41 9723 Accelerator Cable Bracket 42 9424 Intake Manifold 43 — Intake Manifold Nut (7 Req'd) 44 9D476 EGR Valve Gasket 45 — Exhaust Gas Recirculation (EGR) Valve Bolt (2 Req'd) 46 9D475 EGR Valve 47 — Fuel Injection Supply Manifold Bolt
(2 Req'd) 48 9F593 Fuel Injector 49 9D930 Fuel Charging Wiring 50 6786 Oil Level Indicator Tube Bracket 51 — Oil Level Indicator Tube Bracket Bolt 52 6754 Oil Level Indicator Tube 53 6750 Oil Level Dipstick 54 9D280 Fuel Injection Supply Manifold 55 — Vacuum Fitting 56 9E498 Main Emission Vacuum Control Connector 57 — Vacuum Tap 58 — Vacuum Hose 59 9B989 Throttle Position Sensor 60 — Screw and Washer 61 9F782 Throttle Position Sensor Gasket 62 — Throttle Body Bolt (4 Req'd) 63 — Idle Air Control (IAC) Valve Bolt
(2 Req'd) 64 9F715 Idle Air Control Valve 65 9F670 Idle Air Control Gasket 66 9E926 Throttle Body 67 9E936 Throttle Body Gasket 68 — Vacuum Fitting 69 — Camshaft Position Sensor Screw 70 6B288 Camshaft Position Sensor 71 8255 Water Hose Connection Gasket 72 — Water Hose Connection Bolt (3 Req'd) 73 8592 Water Hose Connection 74 8575 Water Thermostat 75 6065 Cylinder Head Bolts 76 6500 Valve Tappet 77 6K512 Valve Tappet Guide Plate 78 6564 Rocker Arm 79 6A528 Rocker Arm Seat 80 6A527 Rocker Arm Bolt (8 Req'd) 81 — Ignition Coil Mounting Bracket Bolt
(3 Req'd) 82 18827 Noise Filter Condenser 83 — Ignition Coil Mounting Bolt (4 Req'd) 84 12259 Spark Plug Wire Set 85 12029 Ignition Coil 86 12043 Ignition Coil Mounting Bracket A — Tighten to 5-12 Nm (4-9 Lb-Ft) B — Tighten to 5-7 Nm (3-5 Lb-Ft) C — Tighten to 21-26 Nm (16-19 Lb-Ft) D — Tighten to 2-10 Nm (1.5-7 Lb-Ft) E — Tighten to 8-13 Nm (6-9 Lb-Ft) F — Tighten to 40-55 Nm (30-41 Lb-Ft) G — Tighten to 16-20 Nm (12-15 Lb-Ft) H — Tighten to 20-30 Nm (15-22 Lb-Ft) I — Tighten to 8-10 Nm (6-8 Lb-Ft) J — Tighten to 8-11 Nm (6-9 Lb-Ft) K — Tighten to 23-30 Nm (17-22 Lb-Ft) L — Tighten to 20-40 Nm (15-30 Lb-Ft) M — Tighten to 4.5-7 Nm (3-5 Lb-Ft) N — Tighten to 18-26 Nm (13-19 Lb-Ft)

Feb 24, 2009 | 1995 Ford Escort

2 Answers

2000 chevy impala ls - oil spray under hood inline with serpentine belt


You may have a lower intake manifold gasket leak (or a head gasket leak-slightly less probable) the lower intake can leak onto the serpentine belt and fling oil (and/or antifreeze). The lower intake manifold gasket is usually the culprit here. There is much information about changing it if you are inclined to do it yourself. If not, expect around 800 to 1200 to fix at dealer/mechanic. This is usually accompanied by (but not always) oil in the antifreeze, or antifreeze in the oil...

Jan 18, 2009 | 2000 Chevrolet Impala

Not finding what you are looking for?
1995 Mazda MX-6 Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...