Question about 1990 Nissan 300ZX

Open Question

How to remove my nissan 300zx 1990 side view mirror

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: installing a Nissan Sentra Passenger Side Manual Non Folding Mirror.

had to install a driver side non folding mirror, fairly simply to say the least. There's a cover on the interior of the door, near the window, remove the cover, remove the 3 screws, need i believe a 10mm socket. If a power window, unhook the circuit. Replace new mirror.

Posted on Aug 25, 2008

Ad
dennisgladx
  • 52 Answers

SOURCE: Nissan 300zx no reverse or 4th gear.

Hi,
The first place I would look is the shift linkage for wear and a sloppy connection from wear.
adjustments may be made as a possible fix on the linkage rod.
Glad to be of assistance - Please rate the response - I can learn from your rating. Thank you

Posted on Oct 27, 2008

  • 14 Answers

SOURCE: 1990 nissan 300zx loss of

Check if your injectors with the electrical meter with ohmmeter you should have around 12 ohms on each if you have above 15 ohms that's mean your injector is going bad it has problems ,easier way to check its if you will start the car with cold engine and go by the mufflers and if you will hear from one of the mufflers kinda shoots that's mean on this side of engine is the injector going bad ,the other things it might be mass air flow ground (-) wire which has some bad connection ,if not check all the connections on the ignition coils and injectors,check your spark plugs, and on the end if this problem will continue check your knock sensor!

Posted on Jan 28, 2009

  • 840 Answers

SOURCE: replacing a cracked side-view mirror

well the best way is to take the inside mirro cap off there are 3 bolts that need to be taken out 10mm if its not accessible from there you need to loosenthe trim panel and take it off look around for hidden pop ups take the pop ups out and take the screws out then from there pull the bottom of the door trim out and slide arms around the edges and pull out there then pull up and outThanks for using fix ya. Please rate my response thank you very much

Posted on Jan 31, 2009

  • 255 Answers

SOURCE: replace rear view mirror on nissan sentra

there is a set scre usually allen head that you can screw out and then the plate will slide up and off

Posted on Aug 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 nissan 300zx auto not shifting?


you might have to change your strainer and fluids

Feb 06, 2013 | 1990 Nissan 300ZX

1 Answer

1990 nissan 300zx has a bad fuel smell inside car. Can anyone give me tips on what to look for?


the problem is your fuel lines, in the engine room over the upper planum. they are pretty old and they will crack. Usually that samell comes when starting the engine in cold. Probebly your fuel line are finito. Change them all.
Hope this will helps.

Dec 03, 2011 | 1990 Nissan 300ZX

1 Answer

Where is the Flasher relay located...on a Nissa 300ZX 1989 model


For 1989 Nissan/Datsun 300ZX 3.0L FI 6cyl the Flasher is located in front seating area, driver side, under dash, above brake pedal, mounted on pedal support bracket .

Hope helps (remember rated this).

Jun 08, 2010 | 1990 Nissan 300ZX

1 Answer

I have a high idle on my Nissan 300ZX what could cause this?


I have a Nissan 300zx twin turbo 1990.... The engine and car are in very good condition ... well serviced... The idle speed will not go below 2000 rpm can you help as there is no manual adjustment...????

Apr 22, 2010 | 1990 Nissan 300ZX

1 Answer

Water pump removal for nissan 300zx


Autozone Chilton manual step by step info. for about 10.00

Oct 06, 2009 | 1990 Nissan 300ZX

1 Answer

How to change flywheel on 1990 300zx non turbo?


pull the transmission. remove the torque converter (automatics) or clutch and pressure plate (standards), the bolts for the flywheel are under that. make sure you replace the flywheel with the proper one especially if it's a standard.

Sep 02, 2009 | 1990 Nissan 300ZX

2 Answers

I need help replacing the motor in my right hand mirror of a 1990 300zx. How do I dismantle it?


the mirror element just snaps out, pull evenly on both sides until it releases

Apr 02, 2009 | 1990 Nissan 300ZX

1 Answer

Replace driver side mirror on 2001 Nissan Quest


SECTION 501-09: Rear View Mirrors 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Mirror —Exterior Rear View Removal
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the upper speaker.
    1. Disconnect the electrical connector.
    1. Remove the bolts.
    1. Remove the speaker.
  1. Position the watershield aside.
  1. Remove the exterior rear view mirror access panel.
  1. Disconnect the exterior rear view mirror electrical connectors.
    • Release the wiring harness locator.
  1. Remove the exterior rear view mirror.
    • Remove the bolts.
    • Feed the wiring harness through the door opening.

Mar 31, 2009 | 2001 Nissan Quest

1 Answer

There three computers in a 300zx where are they?


Hi, the ECU (engine control unit) is located under the passangers side foot panel (if your sitting on the passanger's side, where the tips of your feet hit). Remove the floormat and there should be an area of the carpet that is partially detachable, being held by velcro. Under the carpet there should be a wooden board which you can take off by removing 4~5 10mm bolts. Once you remove that the ECu will be the brass colored metal box with all the wires pluged into. There are 3 10mm bolts to remove the ECU. Hope that helps. :)

Feb 05, 2009 | 1992 Nissan 300ZX

Not finding what you are looking for?
1990 Nissan 300ZX Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...