Question about Cars & Trucks
There is a special procedure involved in keying your fob to your car once the battery has been changed. You must lock and open the door with your key. Turn the ignition to "on"(not start) then push the fob's open and close button, then shut off ignition. This procedure is done everything the key battery is changed. Hope this can help you!
Motorcycle Diagnostic Scanner
Posted on Nov 01, 2012
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: electronic key on 2008 jeep
electronic key on 2008 jeep cherokee says key damaged or key not programmed. car won't start. some things work but radio won't come on. etc..
Posted on Aug 24, 2011
I have the same problem with my 2008 Grand Prix - replaced the batteries in both key fobs - they worked for a few days and quit working. Remote start does not work and both of the cigarette lighter chargers do not work either. I have recieved a "charging system failure" message on the readout screen as well. I have checked with 2 different mechanics and they are not sure what it is. Any help would be appreciated. Thanks!
Posted on Dec 01, 2010
SOURCE: renault key fob doesnt work
I have a clio II, 2001, i have the same problem and i fixed it.
Don't know if will work for you but here it goes:
1 - no key in ingnition
2 - press the unlock button in console off the car for about 10 seconds(dont let go)
3 - it should work the central doors one time and then 2 times( hear)
4 - press the remote a few times until it starts working
It worked for me hope the same for you.
Please tell me if it worked and pass the message.
Posted on Sep 15, 2009
1. Close and lock all doors with the driver’s side power lock/unlock switch.
2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.
3. Insert key into the ignition cylinder and turn to the ACC position.
4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.
5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).
6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.
Posted on Nov 16, 2009
all keys/car have to be programmed at the same time.using nissan diagnostic machine.you could try a quickfit centre (if they have correct machine)
Posted on Feb 17, 2010
Tips for a great answer:
Aug 24, 2016 | 2008 Nissan Altima
Jun 06, 2015 | 2008 Nissan Altima
Mar 09, 2015 | 2008 Nissan Altima
Jan 30, 2013 | Nissan Altima Cars & Trucks
Sep 21, 2012 | 2009 Nissan Altima
Sep 03, 2012 | Cars & Trucks
May 21, 2012 | 2008 Nissan Altima
not starting or turning over indicates towards multiple possibilities. It can
be issue with battery or weak battery. But if battery checks out ok, then it
can be starter issue or faulty alternator or problem with low fuel pressure or
no spark at spark plugs due to dirty spark plugs or faulty ignition
coil or injectors getting cracked or dirty and needs to be cleaned.
confirm the problem, the basic troubleshooting is required.
this link below and follow the troubleshooting:------
This will help.
Feb 19, 2012 | 2008 Nissan Altima
Jan 05, 2012 | Mazda Cars & Trucks
2,242 people viewed this question
Usually answered in minutes!