Question about Ford Cars & Trucks

1 Answer

No power to blower switch

Their is no power to fan switch

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 76 Answers

I don't know what your working on but if you don't have power to the heat switch it is a fuse,you should have one inside and one under the hood.I don't know what kind or the year of car..

Posted on Oct 31, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2009 blower motor not working.yellow wire has power when key is on even if fan speed switch in off position. Shouldn't it only have power when fan speed switch is turn to on?


It depends on how the circuit is set up , It may go through the fan to switch to ground . What make , model an year vehicle ?

Jul 15, 2016 | Cars & Trucks

1 Answer

02 sunfire


If the 30amp blower fuse has power, and you can run power to the blower motor and it runs, I would say its the blower relay or the control switch on the dash. The control switch provides power to turn the blower relay on. The fan switch provides the ground circuit.

Feb 27, 2014 | Pontiac Sunfire Cars & Trucks

1 Answer

2000 Ford E-250 appears to not be getting power to common blower relay terminal. Fan runs on all speeds when 12V is sent to blower motor. Why power loss to common relay terminal. IS there a way to ope


Not sure what a common relay terminal is.
The blower relay gets power from a 50amp fuse. Power goes to the blower motor and the resistor and speed switch provide the ground circuit. The on signal for the blower relay comes from the selector switch.

Jan 24, 2014 | Ford E250 Cars & Trucks

1 Answer

After i change thebrake switch will my fan blower for my heater and ac start working agian


No it won't.The brake switch is for brake light,interlock shift solenoids,transmission TCC controls,and stoping the vehicle, You fan blower has a completely different power supply that is independant from the brake electrical system, For you fan blower to operate its either the fan resistor blower or the fans control switch to the fuse

Mar 19, 2012 | Cars & Trucks

1 Answer

Blower motor not working at all,,the fuse is good and the fan blows if i jump it to the battery


HI Get a test lamp.With blower control switch on high ,remove power wire from blower motor,see if you have power at wire ,if not check for power at blower resister which is mounted next to fan motor.You should have power on two wires,one coming from switch the other going to fan.If you have power going to resister ,the resister is bad ,if no power to resister, switch has a problem Good Luck

Dec 21, 2010 | 1997 Ford Explorer AWD

1 Answer

Replaced the fan resistor on 2000 chevy malibu this summer. Worked fine but recently the blower won't work on any speed.


this could be a bad blower or the switch to blower,check at blower fan for power if no power it is most likely the switch.if there is power on all speeds then the blower is bad. check all fuses to verify.

Nov 17, 2009 | 2000 Chevrolet Malibu

1 Answer

Blower motor doesn't work and has no power to it


Check the blower multispeed control resistor pack is not faulty.
The resistor pack is usually located in the air ducting, in the blower fan airflow.
Basically, +12v power is supplied (via fuse) to the fan speed control switch, which then passes via the selected speed control resistor, to the fan motor. Often a interface relay is used to switch the blower motor high current.

Aug 31, 2009 | Dodge Pickup Cars & Trucks

1 Answer

No Electrical Power to Heater Blower


First thing to check would be the fan speed resister, fan(blower-motor)relays, and possibly a bad ground. Start at switch on the dash and go to the relays and resister next.

May 15, 2009 | 2003 Mitsubishi Galant

2 Answers

Auto Repair: Fan switch or blower, how do I determine which is bad?


there is a thing called a blower motor resistor that controls the fan on cars these days. they are usually in the air box. check with a dealer for your car. its easy to change.

Oct 26, 2008 | 1998 Acura Integra Type R

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...