Question about Cars & Trucks

Open Question

Replacing 2001 toyota corolla clutch master cylinder

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: clutch sliding or slippage

Chech the free play on the clutch pedal it could be to tight. If so adjust the pin in wards of the clutch master under the dash board so that has free play.

Posted on Jan 12, 2009

Ad
  • 1596 Answers

SOURCE: How do I bleed the clutch master cylinder

Same as You Bleed Any other System Being carefull not to get air IN and IT sometimes TAKES FOREVER ________ STICK WITH IT ------ Took Me 2 hours One time

Posted on Jan 19, 2009

localwonder
  • 6784 Answers

SOURCE: how do you replace clutch in 1997 toyota corolla?

I see. sounds like you need a new clutch. OK, here is a step by step guide to follow. it will help with the removal and installation of your new clutch.

Remove the Old Clutch Step1 Verify that your vehicle's clutch is the source of your problems and not the pedal-arm bushings, activating cables or the slave-master cylinder. Step2 Unhook the positive battery cable, the clutch cable or hydraulic slave cylinder to get the transaxle ready for easy removal. Eliminate anything that may hinder your efforts, including exhaust pipes and the speedometer. Step3 Secure your car in a safe position before jacking up the front end. Step4 Stabilize the engine with a jack below the oil pan. Remove the transaxle by undoing at least one engine mount. Step5 Separate the engine from the transaxle by removing the bolts that surround the flywheel bell housing. Step6 Push the transaxle away from the engine until the input shift clears the pressure plate. Step7 Disengage the bolts surrounding the pressure plate and take it and the clutch disc out. Check to see if the flywheel's friction surface is scored, checked or has hot spots. Remove, machine and reinstall the flywheel, if needed. Step8 Examine the pilot bearing (bushing) located at the flywheel's center to be sure the needle bearings are lubricated and that there's no galling. Also look for any oil leaking around the rear main engine seal. Replace the clutch Step1 Follow the instructions for replacing your car's clutch carefully to avoid having to remove the transaxle. Step2 Check that the transaxle's input shaft isn't leaking; replace if needed. Step3 Take out the flywheel and the old seal and install a new seal. Install a New Clutch Step1 Clean the crankshaft flange before putting in the flywheel. With the flywheel on top of the flange, secure the bolts in a star formation to the specified torque for your vehicle. Step2 Install the clutch disc and pressure plate. Prior to putting in the transaxle, attach the new release bearing to the release fork. The fork should move freely. Step3 Hoist the transaxle into position and move it forward until the input shaft glides into the clutch disc's spindled hole. Do not apply force. Step4 Reinstall any bolts or mounts that were removed to replace your car's clutch. Grab the transaxle, release the jack and lower your vehicle. Step5 Consider replacing your car's clutch cable. If you don't replace the cable at least adjust it for the right amount of free-play. Step6 Confirm that your clutch's self-adjusting action is performing correctly by depressing the slave cylinder's piston into its bore. Step7 Drive your car to be sure your clutch is working properly.


PLease rate and god bless:)

Posted on Apr 03, 2009

  • 14 Answers

SOURCE: How do you rplace an ignition lock cylinder on a 98 toyota corolla

You can do this one yourself if you want it does not require removing the steering wheel. just the plastic housing from the steering column.
remove housing/cover. then look at housing with cylinder lock assem. on bottom about 1.2 inches or so from the end of the lock assembly you will see a very small hole insert metal pin into hole and push in while turning the key in the ignition backwards to accessory positionyou will feel the pin your pushing move in a bit, then you should be able to pull the cylinder assembly out. insert new assembly with key in the same position and turn forward this will install your new assemlby then reassemble your plastic column covers.

Posted on May 26, 2009

snk_trd
  • 11 Answers

SOURCE: toyota corolla 2001 model manual transmission have

ok....I am guessing that you are grinding the gears...well in that case make sure your clutch and the pressure plate for the clutch is in good shape. also make sure the throw out bearing is good. If all of them are good then check your Clutch Master Cylinder and Slave Cylinder...both of them can cause the clutch slippage....!!!

Posted on Aug 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the clutch fluid reservoir on a 2006 toyota corolla


The brakes and clutch share the brake master cylinder reservoir,and a line from clutch master cylinder goes to the brake reservoir and it takes brake fluid,dot 3 type.

Jan 19, 2014 | 2006 Toyota Corolla

1 Answer

Clutch stick gets stuck and I can't change gears


It can be due to the:
- Engine rpm high.
- Brake oil level too low.
- Brake oil contaminated.
- Air in the clutch system. (Bleed air)
- Worn out master cylinder clutch, upper. (Replace)
- Worn out clutch cylinder clutch, lower. (Replace).
- Worn out clutch plate. (Replace)
- Worn out pressure plate. (Replace).
- Clutch bearing defective or seized. (Replace).

Aug 30, 2013 | 1999 Toyota Corolla

2 Answers

I dont know were the clutch cable ajustment is.


There is no clutch cable. The single, dry disc type clutch uses a hydraulically operated master cylinder and a release cylinder mounted on the clutch housing. The clutch release cylinder is not adjustable. Clearance is automatically compensated for by internal design of the cylinder.

If your clutch is not releasing properly, the most likely cause is a worn out clutch disc, which will require more travel to disengage than the hydraulic system is designed to provide. It is either this, or your master and/or slave cylinders need replacement.

May 24, 2011 | 1992 Toyota Corolla

1 Answer

Why would the engine engage when the clutch pedal is almost all the way out? The car is 1991 corolla and the clutch fluid reservoir has needed to be refilled several times.


Sounds like you are loosing fluid because of a leaking slave cylinder or slave master cylinder. Air is probably entering the system through the leak, causing a weak clutch pedal, or your clutch plate is worn and also needs replacing. Have them both inspected and replaced if necessary.

Oct 14, 2010 | 1998 Toyota Corolla

1 Answer

I have a 98 Toyota Corolla VE. We changed the


CHECK CLUTCH MASTER CYLINDER.SEE IF YOU HAVE FLUID IN IT.YOU COULD HAVE KNOCK THE FLUID LINE TO CLUTCH MASTER CYLINDER A LOOSE.WHILE WORKING ON VALVE COVER.

Apr 24, 2010 | 1998 Toyota Corolla

1 Answer

Clutch does not engage


Did you check slave cylinder? is the clutch master cylinder empty

Apr 11, 2010 | 2005 Toyota Corolla

1 Answer

Clutch died on my Corolla while driving up hill. How much to repair/replace?


it is either the master cylinder or the slave cylinder mine just went in my cavalier and i replaced the slave (60$) then found out it was the master (300) and i paid a buddy 200 to do it but a garage would cost alot more.

Nov 10, 2009 | 1985 Toyota Corolla 2 Door

1 Answer

CLUTCH ADJUSTMENT 1997 TOYOTA COEOLLA


This vehicle has a hydraulic clutch system check the fluid level in the clutch master cylinder it is located on the firewall near the brake master cylinder fill it if its low than check hydraulic system for leaks, possibly slave cylinder, you will have to rebleed the system if part replacement is neccassary

Apr 11, 2009 | 1997 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...