Question about 2001 Audi A4

1 Answer

Fitting a towbar

We cant get the black part of the bumper off to fit the towbar

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thank you very much for replying i solved my problem by getting an audi manual.
regards
denise

Posted on Jan 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fit towbar


rear bumper off
the towbar should bolt on as is
then wire up

Aug 23, 2014 | 1997 Mitsubishi Magna

1 Answer

2004 series 3 BMW 316i fitting a Towbar mainly how to remove rear valance


you shouldnt need to remove the rear valance to fit a towbar ,i would suggest you contact a authorised towbar fitting workshop as it is not permitted to fit a towbar yourself ,it has to be done by a company with the correct authorised dealership as the towbar has to be certified with a europeon certificate of homoglonation and a plaque .then vehicle has to be presented at the vehicle inspection station for conformity .Then the paperwork of the vehicle changed to show its fitted with a towing hitch and a fee paid for this service .alicantecoli_18.jpgalso the electrics have to be connected by a auto electrician as every annual vehicle inspection the electrics are tested as well where a towbar is fitted .

May 29, 2011 | BMW 318 Cars & Trucks

1 Answer

Directions to install witter towbar on ford focus


Towbars are fairly simple, if the towbar fits the frame, you are all set, if it doesn't, you have the wrong one. If there are holes that line up, use them, if not, you can drill through the frame very easily, it is soft steel, Put some bolts in there that go through about 1/2 longer than the frame parts. Support the towbar with a jack, make sure it stays put. Drill a small pilot hole first with about 1/4 inch bit, then go to the hole size of the towbar, 1/2 inch. Those step bits work great, put in the bolts, tighten them up, all set. As far as positioning this thing, I would make the ball stick out just past the bumper, if no hole line up. You don't want to be smashing the trailer into the bumper all the time, so make sure it is enough, but not so much that you trip over it. Hope this helps.

Jul 29, 2010 | 2000 Ford Focus

1 Answer

How to drop rear bumper to gain access to towbar wiring,changing to 13 pin


is there a mod kit to make the no 10 pin from a spare to a live when ignition switched on with a factory fitted towbar. vw giving the runaround

Feb 28, 2010 | 2009 Volkswagen Tiguan

1 Answer

I want to fit a towbar to my ford focus hatch 2008 model. What is involved in removing rear bumper Regards Brian Lamb


Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well
lining.

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Oct 27, 2009 | 2007 Ford Focus (3 Door) Hatchback

1 Answer

General instructions for fitting a towbar to a 1994 renault clio


remove the rear bumper and the bar bolts to the back panel, some have a stay that bolts up forward. you might have to cut a slot in the bottom of the bumper to clear the towbar.

Oct 21, 2009 | 2000 Renault 181

1 Answer

Cant find the towbar electrics plugs for x-type


I assume that the towbar didn't come with a proper wiring kit as, unfortunately there is not a specific connector for the towbar wiring on the x-type, the proper Vehicle Specific Kit plugs into the rear light. There is a power connector with three pins on the left and a grey reverse sensor cut out connector also on the left. but you will either need to use a Vehicle Specific Wiring kit (about £175) or use a bypass relay system.

Aug 30, 2009 | 2006 Jaguar X-Type

2 Answers

Saab 93 bumper removal


It depends on what year your car is,

If it's the pre 02 car then inside the boot there are 2 M10 nuts near the tie down eyes, remove these and then pull the bumper tips outwards whilst pulling the bumper rearwards.

If its the post 02 car then remove the torx screws inside the wheelarch 2each side, remove screw from bottom edge of bumper near to wheel arch each side, remove 2 plastic nuts from lower bumper near spare wheel well, remove rear light clusters then remove the screws behind them, unclip ends of bumper from bodywork and pull rearwards.

May 22, 2009 | 2008 Saab 9-3

1 Answer

I WANT TO FIT A TOWBAR TO MY 05 REG X TYPE ESTATE JAG


Yes you do need to remove the bumper, remove the 2 torxs screws in each wheelarch, 1 upper bolt and 1 lower bolts behind the wheelarch liner each side. two nuts inside car each side along upper edge, 4 nuts behind trim on rear edge, and 3 plastic plugs along lower edge. Hope this helps

Jan 26, 2009 | 2007 Jaguar X-Type 3.0 Sedan

Not finding what you are looking for?
2001 Audi A4 Logo

Related Topics:

500 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13152 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...