Question about Cars & Trucks

1 Answer

How to find ignition coil diagram for 351 cleave enginee 1972

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,380 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My enginee is not getting fire


What is year--make--model and engine size?
How long since a tune-up? Are there any applicable trouble codes? With gasoline engine, if your saying no spark, have to check spark plug wires--spark plugs--ignition coil, primary voltage and ground for the ignition coil or coil pack.
Also, test with engine cranking, spark--proper fuel pressure and fuel injector pulse. If your missing all three have to check for rpm signal.

Mar 06, 2016 | Cars & Trucks

1 Answer

Trying to figure out why a normal 1970's Ford 351c Freeze plug is way to small for my 1972 Ford 351 Cleveland?


measure the diameter of the welsh plug holes that you need plugs for and any spares shop will have a GeeJay kit of welsh plugs that will have the plugs you want
The idea is to fit the plugs , the problem of why can be answered later after the job is done

Nov 28, 2015 | Ford Cars & Trucks

1 Answer

1972 XB GS Ford Falcon V8 require emmission hose diagram


There are NO emissions diagrams for XB V8 Falcons.
The ONLY emissions hose they have is a PCV in rocker cover connected to the air cleaner housing.
http://www.aus-ford-uk.co.uk/assets/images/351-2v-xb.jpg

Jan 16, 2013 | Ford Cars & Trucks

1 Answer

How do I fix Diagnostic code 351


1. Check for power to the ignition coil when cranking.

2. Check continuity between the Powertrain Control Module (PCM) and the coil on the coil ground circuit wire.

3. Check connections at the coil and at the PCM.

4. If good, replace the ignition coil.

5. If the problem is still there, replace the PCM.

Jun 26, 2012 | 1997 Jeep Grand Cherokee

1 Answer

What does a wiring diagram look like for a 1972 corvette i want to see the wiring from coil to starter and alter


you can go to the libeary and borrow a book for your car .check for the wire diag.

Jul 26, 2010 | 1972 Chevrolet Corvette

1 Answer

I need a blow up diagram of a 1972 steering column i need ti change the ignition switch but dont wanna screw it up


I recommend you pick up the Haynes or Chilton's repair manual on your vehicle. That will provide the diagram and instructions on how to properly do the job you have in mind.

Jun 26, 2010 | 1972 Chevrolet Corvette

1 Answer

No fire out of coil ! ,changed coil, new battery , battery line seems to give off weak spark.still no spark out of coil 73 vette with points distributer


Very likely the points are bad.

if you have replaced the points and capacitor and the coil, then the only other components are the wires and the resistor.

It is simple to troubleshoot if you have a volt meter.

With the ignition on, there should be 12 volts across the primary side of the coil (the small connections).

Do not attempt to measure the secondary side of the coil (the big connection on the top) it will blow out your meter.

If there is no voltage on the primary side of the coil, it is a bad resistor or a broken wire.

This page has a diagram of an automobile ignition circuit that is similar to the one in your car.
Click Here

Good Luck!

Jan 03, 2010 | 1972 Chevrolet Corvette

1 Answer

How do i adjust the valves on a 69 351 windsor motor


The only 351 Windsor with solid lifters is the 351 "R" 4V
1971-1972 Boss 351-HO. All others are hydraulic. To solve noise in hydraulic lifters, replace them and check push rod ends for wear (actually you really should change them, too) but many guys go "cheap charlie" on this.

Nov 01, 2009 | 1966 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...