Question about 2009 Dodge Caliber

Open Question

How to replace brake pads on 2009 dodge caliber

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: brake pad replacment on 2004 Dodge Ram 1500

Remove two bolts holding caliper on and pull up as hard as you can on the caliper. Wiggling back and forth at the same time helps.

Posted on Aug 02, 2008

Ad
MrScary66613
  • 1990 Answers

SOURCE: Front disc brake pads on a 1997 dodge intrepid.

The Calipers on the Rotor that Hold the Brake Pads have Bolts on the Back Side at the Top and Bottom for Mounting. Just feel around back there and you will find them. Remove these and the Caliper will come right Off. Let me Know if you need more Help! Please Rate My Response! Thanks!

Posted on Jan 31, 2009

  • 66 Answers

SOURCE: 2006 dodge ram 2500 4x4 diesel replace brake pads front and back

Straight forward job. Remove wheels, remove 2 caliper bolts per wheel, check bolts,and bushings for wear/corrosion and lubricate, remove calipers, remove brake pads, push caliper pistons into calipers, replace anti-rattle clips, put new pads in, put caliper and bolts in, put wheels on. Start truck and press brake pedal several times to take up slack and you're done.

Posted on Jun 02, 2009

richardrb123
  • 26 Answers

SOURCE: Replacing front brake pads on 2005 Dodge Stratus

jack up the car take the wheels off the caliper which holds the pads need to come off usally 2 bolts if you are replacing the rotors you may have to hit them with a hammer to break the free if they have little clips on the rotors you can grabb the clips with pliers and take them off you do not need to replace them make sure you push the pistons on the calipers back in clean and lube the pins and the any where the rest on the knuckle do get lube on the rotors put it all back together do the same on the otherside before you start the car pump the brakes until a good pedal then you are good to go i hope this helps you

Posted on Apr 13, 2010

bikinimechan
  • 220 Answers

SOURCE: Replaced brake pads on 2009 Dodge Journey, but now

Well you need to check your fluid level on the master cylinder first. Then I suggest that you bleed the brake system. Always start bleeding from the wheel furthest away from the master.

Posted on Nov 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a problemis with my dodge caliber 2009 the transmissoin dos not changing,


how to check dodge caliber cvt transmission ... - CarGurus

www.cargurus.com > Questions > Dodge > Caliber
CarGurusMar 20, 2010 - I bough used Dodge caliber SXT 2008 & i don't know how to check the CVT ... I have a 2009 300c and 2010 caliber and both tranmission are ...

Jul 20, 2015 | 2009 Dodge Caliber

2 Answers

1999 dodge ram 1500 brakes


Hello......on the Dodge ram....either a 3/8th inch allen wrench or a half inch socket removes the 2 bolts.....I've seen 'em both ways....I hope this was helpful......Let me know what happens......PEACE......

Feb 29, 2012 | Dodge Cars & Trucks

1 Answer

How to change 2001 crown victoria brake pads


Jack up car, remove the wheels, take out the two retaing bolts on the brake caliber, slide caliber up off brake disc, remove old brake pad, use a C-Clamp or big pair of Channel locks to compress the piston in to the brake caliber, Insert new brake pads onto caliber, slide brake caliber back over brake disc, reinstall the 2 retaining bolts. put tire back on. Repeat this till you have replaced all pads that you are going to change. ***Caution.. Before putting the car in gear, crank it up and pump the brake pedal till you have a firm brake pedal. If you fell to do this you will have no brakes due to the pistons on the calibers are compressed and are not seated on the discs.

Jan 08, 2011 | 2001 Ford Crown Victoria

1 Answer

My mini van 1999 dodge caravan , the front drivers side wheel , breaks squeak while driving but not when i apply breaks the break light comes on intermittently . what could be the problem ?


this is likley to be a sticky piston in the brake caliber,,,stirp the brakes out on both sides of the car and free off the pistons by cleaning them first then pushing them right back into the calibers chace that the caliber is free to slide as well use copper grease on the caliber pins and on the "back" of the brake pads,, check there is plenty of life left in the pads if not fit a new set to "both sides" dont just fix one side do both sides or the car wont stop in a strate line or may pull to one side!

Aug 04, 2010 | Dodge Caravan Cars & Trucks

1 Answer

How do i get the brake pad clip off of a 2003 2500 dodge 4x4 so i can remove the old brake pads?


you mean the caliber, thats easy there are two boltz holding the caliber on remove them and take off the caliber. for futher help or questions please call me at 419 689 1114

Apr 18, 2010 | 2004 Dodge Ram 2500

1 Answer

How to replace brake pads on 2006 oddesey


Raise and secure on stands after breaking loose the lug nuts and parking brake on for front pads.. Remove wheels and spread old pads back to push cylinders back in their bores on calibers to allow for thickness of new pads. Remove the 2 sliding claiber retaining bolts and rotate caliber out of mount and secure with wire, boungie cord, or rope to take weight of caliber brake hose. Remove old pads, install new, and reassemble in reverse order. Lugs on alloy wheel should be torgued to 95 foot lbs. Block front wheels, release parking brake,and do the back ones the same way. After completing, pump brake pedal slowly several times to seat new pads. If you move the MPV without pumping first, you will have no brakes to stop. If brake fluid level is high in master cylinder, you will need to take some out first to make room for returning fluid from caliber pistons being returned to their bores prior to any brake work. Rotors should be replaced or turned if scored or warped to have better clapping of pads to rotor surface.

Dec 12, 2009 | 2006 Honda Odyssey

1 Answer

Front drivers side disc brake on 2001 dodge stratus. put on new rotor and brake pads. Get up to around 5mph it makes a noise, until brakes are hit. accelerate the noise starts again. outer brake pad is...


The piston from the caliber will keep the inner and outer pads close to the rotor. If outer pads is loose, need to reassemble to find out if it didn't get installed right.

Nov 01, 2009 | 2001 Dodge Stratus

1 Answer

Front calibers keep locking up on my 96 dodge dakota 5.2


I would replace the rubber brake hoses at the calipers. They get damaged internally when the calipers are left hanging while replacing pads. I've seen too many garages and shops do it not knowing what is going on inside the hose.

May 06, 2009 | 1995 Dodge Dakota

2 Answers

2007 dodge grand caravan


according to the service manual there are two bolts hold the caliber to tthe adapter plate and the caliper should roll up and out. the only problem i could imagine is if the pads are hanging in the adapter

Nov 21, 2008 | 2005 Dodge Grand Caravan

Not finding what you are looking for?
2009 Dodge Caliber Logo

Related Topics:

1,070 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...