Question about Chevrolet Cars & Trucks

Open Question

Tourque spec front wheel bearing on 2001 2500 silverado

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2005 SATURN VUE ABS, AWD, R/FRONT BEARING REPLACEMENT

just did one today. removed housing from car, and used a press . be careful of aluminum housing. also used penatrating spray. clean oxidation from inside bearing hole,then lubricating, helped in installation

Posted on Dec 28, 2008

Ad
  • 1 Answer

SOURCE: Torque specs for front wheel hub nut

112 to 174 ft lbs

Posted on Apr 04, 2009

techbuster
  • 5081 Answers

SOURCE: Torque specs on a 2006 chevy silverado front hub

The nut on the axelshaft is 177 ft. LBS.
The 4 bolts on the bearing hub is 133ft. LBS.

Posted on Sep 14, 2009

richardsimpl
  • 230 Answers

SOURCE: what are the front wheel bearing torque specs for

Hi there
i read your report. It 155 to 210 foot lbs. I recommend start off your lowest settings. I wouldn't any higher then 195 foot lbs. hope this info helps you.TY you for writing to fix ya.

Best Regards Richard

Posted on Dec 03, 2009

MNfisherman
  • 11896 Answers

SOURCE: 2004 silverado 4x4 2500 left front wheel bearing

  1. Raise and support the vehicle.
  2. Remove or disconnect the following:

    Tire and wheel assembly Caliper and rotor Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle Electrical connection for the wheel speed sensor Front drive halfshaft assembly on four wheel drive models Hub and bearing assembly mounting bolts Hub and bearing assembly O-ring seal from the steering knuckle bore (2500 series)
  3. Clean and inspect the O-ring seal
To install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly.
  2. Install the O-ring to the steering knuckle (2500 series).
  3. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent.
  4. Install or connect the following:

    Hub and bearing assembly Hub and bearing assembly mounting bolts. Tighten the bolts to 133 ft. lbs. (180 Nm). Front drive halfshaft assembly on four wheel drive models Electrical connection for the wheel speed sensor Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle. Tighten to 106 inch lbs. (12 Nm). Rotor Tire and wheel assembly.
You can go to autozone.com and register for free online repair manual with everything you need.

Posted on Jan 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for a front axle bearing/hub?


Not sure about your model, but in general they are usually around 180 ft./lbs.

Aug 01, 2014 | 2003 Chevrolet Silverado 1500

2 Answers

Wheel Baring Torke spec


2 wheel drive should be between 12-15 ft-lbs
4 wheel drive would be between 130-135 ft-lbs

Jan 18, 2012 | 2005 Chevrolet Silverado 1500

1 Answer

ABS enguaging on its own. Replaced both front wheel bearings. What would cause this? Had a recent MVI done and the Mechanic said the front Right wheel bearing need to replaced. He put a new on on and...


Not supposed to use air gun on axle nut

Torque Wrench -- as you did

Check Wheel Sensors -- one may be bad or more
likely the mechanic damaged it.

Use a Volt Meter --put on A/C unplug sensor &
put meter on wires and spin the wheels

Do all four & compare

Jul 24, 2011 | 2003 Cadillac Sts

1 Answer

What are the front wheel bearing torque specs? For 2000 Chev silverado 2500 4x4,motor 6.0.


Those vehicles should have a hub assembly which incorporates a bearing and hub in one unit. To my knowledge the bearing is not serviceable. The hub assembly is bolted to the steering knuckle, so there actually is no wheel bearing torque. The tire/wheel assembly bolts directly to the wheel flange on the new hub assembly.

Dec 31, 2010 | Chevrolet Silverado 2500 Cars & Trucks

1 Answer

How to replace the front wheel bearings on a 2004 silverado- 4 wheel drive?


They are simple bolt-in units, though make sure you remove the axle nut and get it loose before loosening the wheel bearing bolts. Check with a manual or a dealer for the proper torque spec.

Nov 03, 2009 | Chevrolet 1500 Cars & Trucks

2 Answers

1996 Jaguar XJ6 - seeking toque spec for front hub bearing?


They are taper roller bearings, when new something like 8 or 10 pound feet, used ones tigten until only a little play exists (if you have steel wheels leave the wheel on and it is easy to feel the play even if packed with fresh grease) If you overtighten they will growl and overheat and fail

May 23, 2009 | 1996 Jaguar Xj Series

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...