Question about Chevrolet Cars & Trucks

1 Answer

The ABS warning with all the bells comes on , faulty brake message is shown, engine light has come on and brake pedal pushes back at me when I push on it and the brakes have started to

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 74 Answers

U have two problems ur abs problem is probably a bad bearing wich is causing false activation or ( the pedal pushing back) the engine light has came on for a different reason but u need to get the codes for abs and engine

Posted on Oct 30, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: abs brake warning light comes on and rear brakes remain stuck on

I would bypass abs contraption with new line.(87 dually) abs located under drivers side cab looks very susceptible and is known to fail.I would trust my foot before that old thing.Im rippin it out of my truck & replacing it with new line all the way back.Old lines rusted pretty bad.Better safe than sorry.unplug light bulb or just leave it in .Jersey cant say anything if its 94 or older at inspection.that goes for all the lights.For me,older is better.I dont know what setup you have or if you sold it, you could try replacing it for about 160 at advanced.I hope its not the computer screwin up,thats probably a dealer item.Try unpluging hydraulic unit for shits & giggles.Go over rear brakes again before you start cutting.

Posted on Dec 26, 2008

  • 51 Answers

SOURCE: brake and ABS warning lights on, trac off on.

You may have a bad abs controller. You need to get the code for the abs light from a shop or auto parts store.

Posted on Oct 08, 2008

  • 373 Answers

SOURCE: Brake Lights Come On With The Running Lites

Hi... On your VOLVO this problem can be a WRONG BULB. On any one of the sockets.
OK.. The TAILS Lights and STOP lights it's use the Same BULB. But with DOUBLE CONTACT. "1157"
But ONLY on WAGON Models.
ON sedan Use a individual BULB for each one.

I recomend Remove the stop LIGHTS BULBS.
Inpect and be sure to have 2 CONNTACT.
Replace if need.
I'm sure this gonna fix your problem.
OK Now, the Center light work Because use a Individual CIRCUIT. And signal from the Little MODULE Called.
BULB FAIL SENSE MODULE.

OK... I hope this help on your problem.
Thank you for use fixya.

Posted on Aug 08, 2008

Brian032472
  • 150 Answers

SOURCE: Abs/Brake Light ON, although new brakes, ABS still works

I would suspect a speed sensor.

Posted on Jan 30, 2009

  • 126 Answers

SOURCE: dcs and abs light staying on

car is sensing a problem with the stability control system (DSC) or the antilock brake system (ABS). usually an ABS problem will turn off the DSC, so DSC may be ok, just ABS needs a look at.

since its an '08 model, it should still be covered by the BMW warranty provided you live in the USA. take it in and have them fix it. not safe driving with both systems deactivated.

Posted on Feb 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2001 Carerra brake pushes back!


ABS Braking System being activated for some reason

Nov 26, 2012 | 2001 Porsche 911 Carrera

1 Answer

Brake lights come when gas is pushed


The first thing to do is have the body computer scanned for codes to find out whats going on with the ABS system.

Aug 24, 2012 | 2006 Chrysler Pacifica

1 Answer

Brake pedal has alot of back pressure and car moves in gear.Have to press real hard to stop.How to check abs pump if has one where or brake booster or master cylinder?Don't know how to trouble shoot or...


The air seeping is a dead giveaway. Your power brakes are now manual brakes, but stiffer. The diaphram in the brake booster has torn and the hissing noise is the engine vacuum escaping (you hear it louder when you depress the pedal right?). Replace the booster and you will be fine. The brake lights probably don't work because you can't push the pedal down far enought to release the switch. Please rate. Thanks.

Sep 03, 2011 | 1995 Mercury Cougar

3 Answers

Have a 1993 dodge Caravan SE. Purchased it from a man which converted it from ABS to hydraulics. I didn't know it had brake problems till i got it running. He put on a 3 outlet 2 inlet proportional...


if something goes wrong with abs the brake system it reverts back to standard system!! If you can pump brake pedal up and hold it and start engine and it drops thats normal.You say low pedal if you go 15mph on road and check where pedal is when brakes apply.Power brakes will push aLMost to floor while stopped but while moveing you`ll almost go to slide or will go into slide if pedal is pushed to floor.Get on some gravel at 10 mph and hit brakes to a complete stop get out and check to see if all 4 tires slid or 2 front or only 2 rear. this will get you closer to problem good luck.

Jul 12, 2011 | 1993 Dodge Caravan

2 Answers

My abs light comes on occasionally. everything seems fine, then some times I can't stop as well as I should. It seems that the abs is kicking in & it makes ticking noises in brake pedal area. It also...


There's a service bulliten about that problem with rust build-up on the front hubs pushing the sensors out of posistion [ most common on the pickups in areas that use road salt ], it happens mostly at very low speed. The best way to find out the problem is to have the system scanned.

Mar 17, 2011 | Chevrolet Aveo Cars & Trucks

1 Answer

Rr.ABS and the brake lights on


CHECK TO MAKE SURE WITH CAR RUNNING VOLTAGE AT THE BATTERY SHOULD BE 13.5 VOLTS TO 14.5 VOLTS. USE A DIGITAL VOLT METER TO CHECK VOLTS AT BATTERY. WITH ENGINE OFF BATTERY VOLTAGE SHOULD BE 12.5 VOLTS. IF NOT ALTERNATOR NOT CHARGING BATTERY.THAT WILL MAKE ABS AND BRAKE LIGHTS COME ON AND A FAULTY BRAKE LIGHT SWITCH WILL ALSO CAUSE ABS AND BRAKE LIGHTS COME ON.IF ALL LOOKS GOOD.HAVE THE ABS BRAKES SCANNED.IN THIS CASE YOU ARE HAVING BRAKE FAILURE.BECAUSE WHEN BRAKE LIGHT COMES ON THATS WARNING BRAKE FAILURE BECAUSE THE BRAKE MASTER CYLINDER AND ABS UNIT IS TOGETHER AS ONE.NOT SAFE TO DRIVE.COULD LOSE BRAKE CONTROL AT ANY TIME TOW IT IN.

Jan 25, 2010 | 1996 Isuzu Trooper

1 Answer

Rr.ABS and the brake lights on


I have a Chrysler sebring 2004, the ABS and traction control light has come on the dashboard display plus I have now no heater. I think it is a blown fuse but not sure

Jan 24, 2010 | 1999 Isuzu Trooper

2 Answers

Dash break light staying on


un plug the module under the master cylinder and see if brake lamp goes out...if light goes out you may have a rear abs problem..hope this helps you!!

Sep 04, 2009 | 1992 Chevrolet K1500

2 Answers

Abs and traction control lights coming on


Its the abs sensor, if you encounter an ice patch or snow you won't even be able to stop because the pedal will will push back and make the rip grind noise. If you pull the ABS fuse out, you won't have ABS but you can stop and you won't have the grind noise and back pressure for now. Its safer to not have ABS when the sensor is faulty.

Simon Atari
simonkhpa@yahoo.com

May 06, 2009 | 2004 Pontiac Grand Prix

1 Answer

The traction control and abs warning lights comes on.


Start the car for the first time, make sure the lights are doing it. Then push on the emergency brake a few times making sure it comes up all the way (if not help it out by hand). See if the lights stop. The ABS/Tracktion control is shut off when the E-brake is applied in Fords. I don't know if this is true in Chrysler's but is worth a check. If this has any effect on the lights then it's the pedal not coming all the way up or the switch in the E-brake mech coming loose or malfunctioning.

Feb 17, 2009 | 1996 Chrysler LHS

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...