Question about Cars & Trucks

1 Answer

MY CAR TURNS ON WHILE IGNITION SWITCH IS ON ACC

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 444 Answers

Defective ignition switch, Will have to be replaced,

Posted on Oct 30, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 33 Answers

SOURCE: acc positions on ignition switch will not work on 95 Chevy Astro

ignition switch not lock cylinder may need to be addjusted it's on top side of steering column under dash

Posted on Jul 10, 2009

  • 521 Answers

SOURCE: ignition switch won't turn, locked

tumblers in the ignition switch and/or thew key itself is worn down and not pushing the tumblers into correct position. Only fix is to get a new switch assembley or try a fresh cut key.

Posted on Jul 20, 2009

hardinfarms
  • 144 Answers

SOURCE: key doesnt move past ACC

To find out if it's the switch or the lock cylinder just seperate the switch from the cylinder, you will have to do this anyway so now it will be easy to find the problem

Posted on Jul 25, 2009

  • 330 Answers

SOURCE: 1984 911 Carerra - Ignition switch, Locks, ACC

Just replace the electrical part of the ignition,that is the first step
proporsche

Posted on Feb 17, 2010

  • 111 Answers

SOURCE: ignition switch only turns to acc won't turn all

Sometimes a key may not be in all the way & this can happen, try turning it to on & make sure the key is in all the way, if it's not tap on it lightly & it may pop back in allowing you to turn it to off, also make sure it's in park if it's an automatic transmission.

Posted on Jan 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I leave radio on while engine is off?


Rotate the ignition switch to the ACC position

Oct 18, 2015 | Cars & Trucks

1 Answer

Place key in ign. And turns with no clicks btw off acc and start. When you turn off, goes past off to acc no clicks


Hello Ron, If your car does not crank when you turn the key, it sounds as if you have problems with the ignition switch . Or the actuating rod is disconnected.

Apr 10, 2015 | 1998 Buick Park Avenue

1 Answer

ACC stopped working


I would ckeck the ignition switch as the car will start and run but the acc part of the switch could be faulty.

Nov 08, 2013 | 2006 Chrysler 300 Touring

1 Answer

Key wont move ignition switch past ACC to start position. Purchased new key and still doesn't work.


The actual ignition switch, the electrical switch which the key cylinder turns, is probably bad. It is made of plastic and does eventually wear out. Have that part checked out.

Jan 04, 2011 | Toyota 4Runner Cars & Trucks

2 Answers

Lost keys have hot wired it wont start but does turn over wants to go what do i do


Take your title to the dealer, they should be able to make you a key, also do you hot wire hot to ACC/ON hit Start, then release back to on when it turns over? It may not run if you have anti-theft.

Dec 13, 2009 | 1990 Audi 100

2 Answers

1984 911 Carerra - Ignition switch, Locks, ACC


Just replace the electrical part of the ignition,that is the first step
proporsche

Oct 03, 2009 | 1984 Porsche 911

1 Answer

Ignition switch won't turn, locked


tumblers in the ignition switch and/or thew key itself is worn down and not pushing the tumblers into correct position. Only fix is to get a new switch assembley or try a fresh cut key.

Jul 20, 2009 | 1998 Oldsmobile Intrigue

1 Answer

My key will start the car but it wont turn the car off i have to unplulg the distributor to kill theh car. Also the ignition switch in the car rotates all the way around but it has always done that it just...


the ignition switch is an electrical part. The lock cylinder is whre the key goes and it activates the ignition switch. If you pulled the lock cylinder out, you could operate the car with a screwdriver.
Either you have damaged the ignition switch where the lock cylinder goes into it, or the lock cylinder is damaged where it fits into the ignition switch.

this is 96 taurus, don't have 92 sorry

Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect battery ground cable (14301).
  1. Remove lower instrument panel steering column cover (04459).
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.
Installation
  1. NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

    Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch pin into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install lower instrument panel steering column cover with screws.
------------------
Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
DESCRIPTION AND OPERATION Ignition Switch The ignition switch (11572), which is mounted on the steering actuator housing (3F723), operates in the following manner:
  • The ignition switch is cycled through rotation of the ignition switch lock cylinder (11582) through a pin which is part of the ignition switch.
  • The ignition switch lock cylinder also controls the mechanism which provides a positive lock for the transaxle linkage and the steering system.
  • The locking mechanism is located in the steering column housing.
The ignition switch lock cylinder positions are:
  • ACC
  • LOCK
  • OFF
  • RUN
  • START
The key can be removed from the ignition switch lock cylinder with the column-shift transaxle only when the shift lever is in PARK position and the key is in LOCK position.
  • The ACC position operates while the steering and transaxle remain locked.
  • The engine shuts off when the key is turned to the OFF position without locking the steering or transaxle.
Blade Type
The ignition switch has blade-type terminals that engage with one multiple connector. The multiple connector is secured to the ignition switch by an integral connector fastener.

May 05, 2009 | 1992 Mercury Sable

2 Answers

Ignition switch or ignition cylinder??


Ignition Switch They Are Always Going Bad Your Lucky You Can Get It Acc Mode Mine Wouldn't Turn At All. I Went After Market Through A Much Cheaper Version From Autozone But Now I Have One Key For The Door And Another For The Ignition.

Jan 20, 2009 | 1994 Toyota Camry

1 Answer

1997 venture keyless remote programming


SYSTEM OPERATION

System warning lamp located on top of the instrument panel
Press UNLOCK button once , turns on interior lamps and deactivates alarm (if fitted)
Press UNLOCK button twice w/in 5 seconds unlocks all doors, turns on interior lamp and deactivates alarm (if fitted)
To activate alarm system (if fitted):
Switch ignition OFF
Open driver's door
Press Lock button on remote
Close Driver door
warning lamp will flash when system is activated
Press remote power sliding door button will open sliding door (if fitted) only if unlocked first
Pressing remote panic button:
*Sounds horn intermittently
*Flashes exterior lamps
*Turns on interior lamps
**Pressing panic for the second time OR switching ignition ON deactivates alarm.


PROGRAMMING
Remobe key from ignition switch
Remove the "BCM PRGRM" fuse, from the fuse box
Close all doors
Turn ignition switch to the ACC position
With in 1 SECOND , turn the ignition switch to OFF then back to 'ACC'
(really, with in one second)
Open and close the driver's door. A chime will sound, indicating programming mode activated
Press and HOLD LOCK and UNLOCK SIMULTANEOUSLY untill a chime sounds 2 times ( about 15 seconds)
Repeat this exact procedure for all remotes to be programmed
Remove key from ignition
Refit 'BCM PRGRM' fuse.

4 REMOTES MAXIMUM CAN BE PROGRAMMED

Aug 24, 2008 | 2000 Chevrolet Venture

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...