Question about 2005 Hyundai Trajet 2.0

Open Question

Cylinder head bolt torque of hyundai trajet - 2005 Hyundai Trajet 2.0

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ghost4548
  • 776 Answers

SOURCE: i have a 1997 hyundai elantra 1.8 i need torque specs. for head

go to http://www.hmaservice.com/ and register. After that, you'll have access to manuals, service bulletins, wiring diagrams, etc.

Posted on May 28, 2009

  • 1071 Answers

SOURCE: Please provide torque settings for the head bolts

1st stage 45lbs then 65 then 85

Posted on Aug 21, 2009

  • 280 Answers

SOURCE: I need the cylinder head torque settings for 1997

1998 Hyundai Lantra "G4GM" engine 1795cc.there are two heads or blocks, one is called the M10, other is the M12, figure out which one you have cause the torque is different for stage one by 5nm........... Dont get confused theres 2 different engines so 2 different torques for stage1---------
heres the full details: Stage 1 - m10 = 30nm / m12 = 35nm-------------------------- -------- Stage 2 - tighten by 60-65 degrees ------------ stage 3 - tighten by 60-65 degrees. no sequence is given in the data book for tightening so go off what you thinks right, it doesn't matter on this engine.

Posted on Jan 26, 2010

Testimonial: "Very accurate answer. Thanks, all is well now"

  • 181 Answers

SOURCE: Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS

You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Please confirm torque for 95 accent 1.5 head bolts.Thanks


Already answered on Fixya

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.

Cylinder head torque settings for 1995 hyundai accent 1 5

Feb 02, 2017 | Hyundai Accent Cars & Trucks

1 Answer

I need the cylinder head torque settings for a hyundai getz 1.6 16 valve double overhead cam Engine cod G4ED


renew bolts
stage1- 30NM
stage2-90deg
stage3-individually slacken off 360deg
stage4-30NM
stage5-90deg

crank pulley bolt-142NM
cam sprocket bolt-88NM

i like to help people like you that give engine codes it makes it so much easier

Jul 20, 2016 | Hyundai Cars & Trucks

1 Answer

Torque settings head bolt hyundai 2.2 crdi 2006


is your motors head torques listed on

also has torque sequence page number reference layouts are bottom of the document

page 33 as a pdf

or page 50 of paper listings

http://olybrake.com/pdf/fel_pro_torque_specs_guide.pdf

May 11, 2016 | Hyundai Santa Fe Cars & Trucks

2 Answers

Replacing the cylinder head on a 2005 Hyundai Accent 1.6 dual overhead cam, need to know the Tourque Specifications for the cylinder head and intake manifold. thanks


Here's what the shop manual states:

30 Nm (300 kg.cm, 22 lb.ft)+90°+Release all bolts + 30 Nm(300kg.cm, 22 lb.ft)+90° In this instance you don't have a 'Torque to Spec"... you have a "torque to YIELD' In this specification, initially torque the head bolts to 22 lb ft... then turn each and additional 90°, then loosen each and REDO to the same specification = 22 lb.ft)+90° (you're actually crushing the head gasket TWICE and stretching the head bolts TWICE.

Apr 21, 2011 | 2005 Hyundai Accent

1 Answer

Need cylinder head torque specifications 2004 hyundai elantra


Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
. Install the timing belt tensioner pulley.
. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
. Adjust the timing according to "Timing Belt"
. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

. Install the timing belt cover.
Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
. Install the surge tank and tighten the nuts bolts to the specified torque.
. Install the power steering oil pump and bracket.
. Install the ignition coil.
. Install the air intake hose.
Connect the vacuum hose, fuel hose and water hose.
. Install breather hose.

Dec 22, 2010 | 2004 Hyundai Elantra

1 Answer

Just need the torque secuence in the accent 2001 for the cylinder head bolts


1.5L cylinder head bolt torque

step 1 18 ft lbs.

step 2 60 degrees

step 3 additional 60 degrees

1.6L cylinder head bolt torque

step 1 26 ft lbs.

step 2 90 degrees

step 3 additional 90 degrees


johnjnail_30.jpg

Apr 08, 2010 | 2001 Hyundai Accent

1 Answer

How to install head torque for hyundai 2005


4 cylinder? 10 bolts? This is generic. Starting in the center, top first then bottom, move over one position left or right top then make an "X" to the opposite side bottom. Then up and "x" back to bottom. One more "x" pattern for four remaning outside bolts. Final torque around 60 ft/lbs (generally)
Curious, how are you doing this without a repair manual? Tisk tisk.

Mar 25, 2010 | 2005 Hyundai Accent

1 Answer

Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS


You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Feb 19, 2010 | 1997 Hyundai Elantra

2 Answers

Whats the torque for the head bolts on a 98 hyundai elantra


The cylinder head bolts need to be torqued at

  • 10MM bolts 22 FT-LBS
  • 12mm bolts 26 FT-LBS

Jan 20, 2010 | 1998 Hyundai Elantra

Not finding what you are looking for?
2005 Hyundai Trajet 2.0 Logo

Related Topics:

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...