Question about Cars & Trucks

1 Answer

03 hyundia xg350 no power to windshield washer pump(wipers work) new pump

Replaced the pump,tested the new pump,its good.No power to the wires. No fuse to check.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 444 Answers

Defective relay.

Posted on Oct 30, 2012

  • 1 more comment 
  • Eric Gillette
    Eric Gillette Oct 31, 2012

    So the pump draws power off of the wiper relay?? If the relay was bad the wipers wouldnt work would they??

  • Eric Gillette
    Eric Gillette Oct 31, 2012

    Just a question for you Rocky..Sorry if I am a pain,I just gotta get it straight in my brain..Guess I'm a poet and didnt know it too..lol

  • Rocky Degelman Oct 31, 2012

    Not nessasarly,One way to test this, Is to pull the relay out,End see if your wipers work or not, The relay should be located in the fuse block in the engine.(Compartment) But before you try that, If you have a test light ,Unplug the wires from the pump to check if there is power at all to them, With help from a friend, Tern the swictch for the pump on as you are checking to see if there is power in any of the wires,If not there is a break in the wires,Or a problem with the muti funtion switch on the steering colum, Hope this helps you out.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
tommyboinow
  • 324 Answers

SOURCE: rear windshield wiper stopped working, its not the fuse

then it has to be the switch or the motor.

Posted on Nov 26, 2008

  • 1201 Answers

SOURCE: windshield washer does not pump fluid

The pump works off the same circuit as the wipers, so it would be same fuse. Most likely the pump is no bad.

Posted on Jan 31, 2009

  • 840 Answers

SOURCE: Rear Windshield Wiper Problems

Check the wiper motor connection if its touching anything and loose it will automatically ground out and check at connection make sure you put some gel and then snap it in/ Please rate my response thank you very much

Posted on Jan 31, 2009

  • 718 Answers

SOURCE: Rear wiper Ford Explorer 1998 won't work.

Look for the fuse for the rear wiper motor is a 15 amp mini-fuse , in location # 8 of your POWER DISTRIBUTION BOX in the engine compartment. Check in the PD BOX for; - relay # 8 is the rear wiper down relay , and - relay # 10 is the rear wiper up relay .

Posted on May 18, 2009

ourhowse
  • 2007 Answers

SOURCE: rear windshield washer works but front does

Probably need to replace the pump. Separate pumps for front and rear. Check with a test light to see if there is power to the pump. If it has power but won't work, replace the pump. If no power, you have a wiring issue. Be sure to turn the switch on and have someone push the washer button when you are checking for power. There won't be any until you push it to "wash".

Posted on Feb 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Pontiac Montana wipers not working how to fix


First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

Nov 25, 2016 | 2003 Pontiac Montana

1 Answer

Which fuse controls front windshield wiper pump


Do the wipers work ? Fuse for wipers is same as washer pump .
Principles of Operation
The wiper motors receive inputs from the following:
  • Multi-function switch
  • Powertrain control module (PCM)
  • Ignition switch
  • Smart junction box (SJB)
The following components are integrated in the wiper motors:
  • Windshield wiper motor module
  • High/low speed relay
  • Run/park relay
  • Washer pump relay
  • Park sense (Hall-effect sensor)
Washer System
The windshield washer and the rear window washer are activated by the internal wiper motor modules when it receives a ground from the multi-function switch between the washer inputs. Depending on the correct ground, the internal wiper motor modules activate either the windshield washer or rear window washer relays (internal) by grounding the respective relay coil. When either module is activated, it connects voltage to the washer pump while the deactivated module provides ground to the washer pump. In this manner, voltage polarity is reversible to achieve directional change of the washer pump and washer fluid.
  • The washer pump is inoperative
  • Circuitry
  • Washer pump
  • Multi-function switch
  • Windshield wiper motor
  • Rear window wiper motor
  • Go To Pinpoint Test I .
Does your expedition have programmable/recall memory option for seats an mirrors ?
Driver Seat Module
The power driver seat and power exterior mirrors are controlled by the driver seat module (DSM) only when the vehicle is equipped with the programmable/recall memory option.
On the Expedition Limited, the power fold exterior mirror option is controlled by the DSM. Before running a self-test or retrieving codes, the power fold switch must be inactive for at least 30 seconds.
This is a complex vehicle , electronics , control modules an serial data communication networks. You mite be better off taking it to the dealer or some other repair shop . There could be DTC'S - diagnostic trouble codes stored in the SJB - body control module !
B1667 Mirror Driver Up/Down Motor Stalled Go To Pinpoint Test D . B1668 Mirror Driver Right/Left Motor Stalled Go To Pinpoint Test D . B1669 Mirror Passenger Up/Down Motor Stalled Go To Pinpoint Test D . B1670 Mirror Passenger Right/Left Motor Stalled Go To Pinpoint Test D . B1735 Mirror Driver Vertical Switch Circuit Short to Battery Go To Pinpoint Test D . B1739 Mirror Driver Horizontal Switch Circuit Short to Battery Go To Pinpoint Test D . B1743 Mirror Passenger Vertical Switch Circuit Short to Battery Go To Pinpoint Test D . B1747 Mirror Passenger Horizontal Switch Circuit Short to Battery Go To Pinpoint Test D . B2312 Mirror Horizontal Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2314 Mirror Passenger Horizontal Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . B2316 Mirror Passenger Vertical Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2318 Mirror Passenger Vertical Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . B2320 Mirror Driver Horizontal Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2322 Mirror Driver Horizontal Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . Normal Operation During normal operation, when the front wiper wash is selected, the windshield wiper motor provides power to the washer pump through circuit CRW14 (BU/WH) and ground is provided to the washer pump through circuit CRW12 (GY/OG) and the rear wiper motor. If rear wiper wash is selected, the rear wiper motor provides power to the washer pump through circuit CRW12 (GY/OG) and ground is provided to the washer pump through circuit CRW14 (BU/WH) and the windshield wiper motor.
    Possible Causes
  • Multi-function switch
  • Open in circuit CRW14 (BU/WH), CRW12 (GY/OG), CRW07 (GY/BN), CRW20 (GY/YE), SBB49 (RD) or GD149 (BK/GY)
  • Short to ground in circuit CRW14 (BU/WH), CRW12 (GY/OG), CRW07 (GY/BN) or CRW20 (GY/YE)
  • Washer pump
  • Windshield wiper motor
  • Rear wiper motor
    This is

Feb 02, 2016 | 2010 Ford Expedition

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

1 Answer

1999 chevy prizm windshield washer fuse location?


If your windshield wipers are working than the fuse is good. The wiper and the washer use the same fuse.

The washer pump will have power to it all the time with the key in the on position. you can disconnect the connector and check this. The washer pump is grounded by the wiper switch. you can check the other wire for continuity to ground with the washer button depressed.

If there is power and ground at the connector than the pump is bad.

Sep 16, 2015 | Cars & Trucks

2 Answers

I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
Visual Inspection Chart Mechanical Electrical
  • Windshield washer pump hoses
  • Windshield wiper mounting arm and pivot shaft
  • Bussed electrical center (BEC) fuse 10 (30A)
  • Smart junction box (SJB) fuse 3 (10A)
  • Circuitry
  • Windshield wiper motor
  • Windshield washer pump
  • Windshield wiper/washer switch
  • The wipers stay on continuously
  • Circuitry
  • Windshield wiper motor
  • Windshield wiper/washer switch
  • Go To Pinpoint Test C .
PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
  • Key in OFF position.
  • Disconnect: Windshield Wiper/Washer Switch C2137.
  • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Does the windshield wiper/washer switch pass the component test?
Yes
GO to C2 .

No
INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
  • Disconnect: Windshield Wiper Motor C125.
  • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

    Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

    s6b~tr~en~file=n0011980.gif~gen~ref.gif
  • Are the resistances greater than 10,000 ohms?
Yes
GO to C3 .

No
REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
  • Disconnect all the windshield wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all the windshield wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
You

Feb 20, 2015 | 2007 Ford Mustang Coupe

1 Answer

Windshield wiper washer pump fuse


On a lot of cars, that washer pump circuit is really a sub-circuit of the windshield wipers themselves. The wiper fuse is also the washer pump fuse, in other words.

Use a test light or a voltmeter. Pull off the electrical connector at the pump on the washer fluid tank. Have a helper turn the key on, then press for the washer pump to operate. Take your test light and clip the ground lead to the negative battery post. Touch the tester probe to the positive terminal to assure the light is bright, that the test light will work. Now probe the connector at the washer pump. One of them wires should light up the test light, or would show battery voltage with a voltmeter or multi-meter. If it has power when key is on and washer switch on, the motor is bad, or sometimes you have to go a little further and find a ground fault.

If there is no power on any wire at the pump connector, you will have to look at a wiring diagram to diagnose it. Find out just how the pump gets power.

Jan 08, 2015 | Cars & Trucks

1 Answer

Where is the fuse for the front windshield washer motor


If you are just talking about the windshield washer pump/motor that squirts water on the front windshield, there is no separate fuse for that pump. If you are talking about the front windshield wipers themselves then the fuse for that (including the washer pump) is located is the fuse panel inside the vehicle down below and to the left of the steering wheel. Below is a diagram of the fuse layout (first picture) and I marked the 10 amp fuse for the system. As I said if you are talking about the pump/squirter motor there is no separate fuse. Inside the wiper motor itself (located basically on the firewall on the drivers side) is an internal microprocessor as well as an internal relay for that pump. If the processor or the relay is bad, both are internal and the whole wiper motor assy. has to be replaced. It's one complete unit. There is a chance that the pump motor itself could be bad. In the second picture is a breakdown of the washer fluid reservoir. In order to get access at it which is where the washer pump motors are located the right front wheel and splash guard have to be removed. I have marked the 2 washer pump motors which are mounted on the reservoir. I cannot tell you which motor is which but the one for the front has 2 wires at the connector (a black & white wire and a black wire) The rear pump motor has a violet & light green wire and a black wire at its connector. That's how you can tell which one is which. You can test the motor by either pulling it out and applying direct power and ground to it to see if it engauges or while someone is engauging the washer inside the vehicle while you are down there, see if you are geting power at the black and white wire. Check that wire while it is disconnected and using a good separate ground. If you are getting power make sure the black wire is geting a good ground. If all is good (ground & power) than more than likely the pump motor is bad. If you have a power supply problem at the black & white wire than you are looking at most likely a bad wiper motor assy but check for an open power wire from the wiper motor to the pump motor. It's not quite as simple as it used to be. The wiper motor on your vehicle has like a mini computer in it. I'm gonna say the washer pump motor is bad which is the most common. Hope I was able to help and that I didn't get too technical on you but things are not like the old days with separate motors (wiper and washer).

5_20_2012_11_03_19_am.jpg5_20_2012_11_03_40_am.jpg

May 19, 2012 | 2004 Mercury Montery

1 Answer

Rear windshield washer works but front does not....Any suggestions? Washer fluid is full, fuses are good, wipers work but no fluid or sound of pump running when lever is used to spray fluid on front...


Probably need to replace the pump. Separate pumps for front and rear. Check with a test light to see if there is power to the pump. If it has power but won't work, replace the pump. If no power, you have a wiring issue. Be sure to turn the switch on and have someone push the washer button when you are checking for power. There won't be any until you push it to "wash".

Feb 01, 2010 | 2007 Toyota 4Runner

1 Answer

The front windshield washer fluid pump for me 2000 chevy blazer has stopped working. No sound when I press the spray button, just the wipers.


Check the wire harness to the windshield washer pump. The pump is located in the washer fluid reservoir, if the wires are good. Chances are the washer pump needs to be replaced and you can pick up the new pump st Auto Zone or Parts Source and they will have the step by step instructions for you to get the job done with common tools. Good luck and keep me posted.

Jan 18, 2010 | 2000 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...