Question about GMC Cars & Trucks

Open Question

How to reset oil change light 2000 gmc sierra

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 71 Answers

SOURCE: 01 gmc sierra how to reset change engine oil light

Turn on the ignition switch without starting the vehicle and mash the accelerator to the floor 3 times slowly and this should reset the change oil sensor.

Posted on Jan 30, 2009

Ad
  • 6 Answers

SOURCE: 2000 gmc sierra 1500 5.3 v8. a/c heater control problem

your heat/cool and vent selection options are controlled by engine vacuum through small clear tubes attached to the rear of your climate control interface. Other vehicles have small steel pull wires that operate the desired changes. You might try removing the trim and any fasteners affiliated with the interface/console. GENTLY pull outward and look to see if any of these tubes are pulled off or cut/damaged. Did anyone recently install a new stereo in the vehicle? If so, the vacuum tubing and or pull wires that change your outlets could have been damaged when the stereo unit was pushed into place. Hope this helps

Posted on Sep 09, 2009

Testimonial: "Very good information. THANKS!"

SOURCE: Got oil cahnged and now change oil soon light is

Turn the ignition on and within a few seconds slowly pump the gas pedal three times. A message displaying "oil life reset" should show up in the drivers information center. If you have the "newer" driver information center look for an "i" button and scroll through it until you see "oil life **%" displayed. At that point press and hold the reset button until it resets to 100%. Should take about 10 seconds of holding the button.

There should be instructions on how to reset it in the owners manual if this doesn't help. Good luck.

Posted on Oct 06, 2009

Molson02536
  • 3854 Answers

SOURCE: I changed batteries in my 2003 GMC Sierra key fob

1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).

Posted on Mar 06, 2010

  • 6 Answers

SOURCE: HOW DO I RESET THE CHANGE OIL LIGHT ONCE THE OIL

look in the manual......turn the ignition to the on position not starting it of course and then pump the gas petal 5 times then the light will blink a few times turn off then back on...problem solved

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i reset the change oil light on the dash after changing the oil


YOU NEED CODE SCANNER TOOL TO RESET LIGHT/BRING TO GARAGE TO RESET IT

Mar 12, 2011 | 2000 GMC Sierra

1 Answer

How to reset oil change light?


Make and Model: Chevrolet Suburban, GMC Yukon XL, Chevrolet Silverado, GMC Trucks Sierra
Years: 2000-01, 1999-00

Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However, if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.

Hope this help (remember rated and comment this help) Good luck.

May 14, 2010 | 1999 GMC Sierra

1 Answer

I changed the oil and do not know how to delete the message, is ''change engine oil'' in the display panel. what can I do?


Chevrolet Suburban/GMC Yukon XL, 2000-05 Chevrolet GMC Trucks Silverado, Sierra, 1999-05 Chevrolet Venture 2000
Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.

Good luck and please rate. Keep me posted, and thank you for using fixya.

Jan 14, 2010 | 2004 Chevrolet Silverado

1 Answer

How do you reset oil change indicator?


Chevrolet Service Light - For Chevrolet Suburban, GMC Yukon XL, Chevrolet Silverado, GMC Trucks Sierra 2000-01 and 1999-00:

Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However, if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.

I really hope helps with this (remember rated this help) Good luck.

Jan 05, 2010 | 2000 Chevrolet Silverado

1 Answer

How to reset the change oil light on a 2003 chevy silverado


Information courtesy of synthetic-direct.ca
Chevrolet Suburban/GMC Yukon XL, 2000-05 Chevrolet GMC Trucks Silverado, Sierra, 1999-05 Chevrolet Venture 2000
Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.
Best of luck.
Greg

Jul 15, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

CHANGE ENGINE OIL light won't go off.


disconnect battery for 10 min then do what the manual says.

Apr 01, 2009 | 2000 GMC New Sierra 1500

1 Answer

Change oil light stays on


turn key to on position (DO NOT START)
press and release gas pedal 3 times.
leave key on the change engine oil light flashes 5 times than goes away and its reset

The place that changed your oil should have done this for you

Feb 01, 2009 | 2000 GMC Sierra

2 Answers

01 gmc sierra how to reset change engine oil light


Turn on the ignition switch without starting the vehicle and mash the accelerator to the floor 3 times slowly and this should reset the change oil sensor.

Jan 30, 2009 | 2002 GMC Sierra 2500HD

1 Answer

99 gmc oil light flashing


Try reseting it again. Sometimes it takes a couple of tries to get it right.

May 21, 2008 | 2000 GMC New Sierra 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

380 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...