Question about 1990 Nissan Pulsar

Open Question

Installing new stereo in 1997 Pulsar Hatchback

Need assistance to remove front door panels and old Stereo head unit.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 20 Answers

SOURCE: Stereo Upgrade in 1997 Sentra

hi there. I am not sure about the speakers. But there is a wiring harness available for a aftermarket head unit. I have a '97 sentra the base model XE version. I have just put in an alpine head unit and you defenately hear the difference even on factory speakers. But you will need 2 kits to install an aftermarket head unit in the car. 1. A dash kit. I got mine from canadian tire for about 20 bucks, it comes with instructions on how to put it together and its straight forward, just make sure u get the one for your year and make of car.

2. The wiring harness. there available at mostly every car audio place for about 10 bucks. again make sure u get the one for your year make and model of car. installing this is difficult so unless your good at electronics get it professionally installed. you have to splice the wires into the back of the aftermarket unit, then the plugs plug right into your existing factory car harness.

hope this solves your problem, the dash kit is easy to put together and install into the car, but the wiring harness is a bit difficult, i had my harness installed for about 40 bucks and u save money if u put the dash kit togehter yourself because thats 1 less thing they have to do. good luck.

Posted on Jan 11, 2009

Ad
emissionwiz
  • 76846 Answers

SOURCE: stereo wire diagram

1995 Nissan Sentra Car Stereo Radio Wiring Diagram
Car Radio Constant 12v+ Wire: Pink
Car Radio Switched 12v+ Wire: Blue
Car Radio Ground Wire: Chassis
Car Radio Illumination Wire: Red/Blue
Car Stereo Dimmer Wire: Red/Yellow
Car Stereo Antenna Trigger: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Front Speakers Size: N/A
Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Pink
Left Front Speaker Negative Wire (-): Blue
Right Front Speaker Positive Wire (+): White
Right Front Speaker Negative Wire (-): Black
Rear Speakers Size: N/A
Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Light Green
Left Rear Speaker Negative Wire (-): Violet
Right Rear Speaker Positive Wire (+): Blue
Right Rear Speaker Negative Wire (-): Pink

Posted on Mar 25, 2009

  • 14 Answers

SOURCE: Removing Stereo from Nissan Terrano II

I THINK YOU WILL FIND THER IS 4 SCREWS HOLDING IT IN THERE IS ON MINE * *
* *

Posted on Apr 17, 2009

  • 4 Answers

SOURCE: im installing a new stereo and need a wireing

buy a wiring block for the specific Vehicle. the wiring block wires are all labeled. match the block wires to the new stereo wires . After removing
old stereo trace the wires to the factory wiring block.disconnect and plug the new stereo in.

Posted on Nov 12, 2009

  • 11 Answers

SOURCE: 2008 Pontiac Grand Prix Factory stereo color codes

attach both power and illumination wires to constant on car wires.... only way to have switched power is connecting the switched/ignition wire to a fuse

Posted on Apr 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dodge infinity


The Infinity system includes a CD/cassette receiver or a CD receiver in the dash, and a complement of 7 speakers: 3-1/2" speakers in the dash (left, right), a 2-1/2" center dash speaker, two 6"x9" woofers in the front doors, and two 5-1/4" speakers in the rear doors. You'll have to remove a section of the dash to install a new stereo, as you do with the non-Infinity system. You'll need a special adapter to connect a new car stereo to the Infinity factory amp http://www.crutchfield.com/p_120CHTO02/Axxess-CHTO-02-Factory-Integration-Adapter.html?tp=3486


12_25_2013_10_25_35_pm.jpg

Dec 25, 2013 | Cars & Trucks

1 Answer

Dodge durango stereo


The stock amp would be useless if you are going to uprate the rest of your system. Because you will play it louder. You could use it to drive the front door speakers, but I would remove it and fit an upgraded item that will actually improve your system.If you are going to install a new head unit then there is a very real chance that the amp in the new head unit will be better than the one installed by the manufacturer.

Jul 22, 2013 | Cars & Trucks

1 Answer

Nissan Maxima 1997 Stereo not turning on at all!!


Here is a list of radio wiring harness wire color codes and what they do. I have given both with and W/O Bose.

Nissan Maxima Car Stereo Radio Wiring Diagram Radio Constant 12V+ Wire: Pink/Blue
Radio Ignition Switched 12V+ Wire: Blue/Black
Radio Ground Wire: Vehicle Chassis
Radio Illumination Wire: Red/Blue
Radio Dimmer Wire: Red/Orange
Radio Antenna Trigger Wire: Black/Red

Front Speakers Location: Doors
Left Front Speaker Wire (+): Blue/White
Left Front Speaker Wire (-): Blue/Yellow
Right Front Speaker Wire (+): Brown
Right Front Speaker Wire (-): Brown/White
Rear Speakers Location: Rear Deck
Left Rear Speaker Wire (+): Red
Left Rear Speaker Wire (-): Green
Right Rear Speaker Wire (+): Blue
Right Rear Speaker Wire (-): Pink
1997 Nissan Maxima with Bose Stereo Wiring Diagram W/Bose
Car Radio Battery Constant 12v+ Wire: Pink/Blue
Car Radio Accessory Switched 12v+ Wire: Blue
Car Radio Ground Wire: Chassis
Car Radio Illumination Wire: Red/Blue
Car Stereo Dimmer Wire: Red/Yellow
Car Stereo Antenna Trigger Wire: Black/Red
Car Stereo Amp Trigger Wire: Green/White

Car Stereo Amplifier Location: Each speaker has its own amplifier located at each speaker.
Left Front Speaker Positive Wire (+): Yellow
Left Front Speaker Negative Wire (-): Brown
Right Front Speaker Positive Wire (+): Violet
Right Front Speaker Negative Wire (-): Light Green
Left Rear Speaker Positive Wire (+): Red
Left Rear Speaker Negative Wire (-): Green
Right Rear Speaker Positive Wire (+): Pink
Right Rear Speaker Negative Wire (-): Blue


Mar 27, 2017 | 1997 Nissan Maxima

1 Answer

How do you remove radio, from my 2001 dodge neon, that just went dead, for no reason. I replaced the fuse on the side of dash board. Still nothing.


Safety Precautions
  • Before removing the stereo or any other electrical component, it is vital that you first disconnect the grounding cable from the Neon's battery. The grounding cable connects the battery to the frame or chassis of the vehicle.

    Use a Phillips-head screwdriver to loosen the grounding cable's camp from the negative battery lead. Make sure to rest the clamp away from the negative lead post until the removal is complete.
  • Remove the Dash Trim Panel
  • The dash trim panel that surrounds the Neon stereo needs to be removed to access the stereo. The panel contains, but is not connected to, the climate control knobs on the dashboard.

    Grab the panel at the bottom corners and pry it from the dash. You will likely be able to remove the panel without the assistance of a trim pry tool, but if you are having difficulty removing the panel by hand, wrap a thin cloth around a trim panel removal tool or flat head screwdriver to remove the panel.

    Once the lower edge of the panel is relieved from the panel, you can work your hands (or flat pry tool) around the perimeter to separate the remaining edges.

    Since the panel is not connected to the climate control knobs, you will not need to disconnect the wiring to the knobs. The panel, once free, can be set aside until you replace the stereo.
  • Remove the Stereo
  • The Neon stereo deck is held into the stereo mounting bracket by 10 millimeter bolts on either side of the radio. Remove the bolts and store them in the ashtray for safe-keeping.

    Pull the stereo from the dock. The unit will easily slide from the mounting bracket with an even pull from the left and right of the stereo. Pull the stereo far enough to reach the wiring on the rear of the radio.

    The wiring to the stereo includes the antenna, the power supply and the speaker wires. There may also be patch cables connected if an amplifier is connected to your stereo system. Pull the cables from the stereo. The antenna and power supply are single cables. The speaker wires (and patch cables) will be grouped by wire binders. The plastic wire binders should be pulled as a unit. Do not pull the wires themselves.

    Once the wiring has been disconnected from the stereo, the unit will be completely free from the Neon.

    If you plan to operate the vehicle before installing a new stereo or re-installing the factory deck; reconnect the grounding cable to the negative battery lead. Otherwise, leave the cable away from the negative lead until all of your work is completed.
  • Feb 26, 2011 | 2001 Dodge Neon

    1 Answer

    I have c-class 200K 2001, classic, i would to change radio to new one to have DVD/MP3/GPS and bluetooth ....what i have to do


    its not to hard if you have basic skills or better you must remove the old stereo from car which can mean certain parts of the dash will have to come out usually the surround around the stereo you may also need a special tool to get the old stereo out of the dash then you will have to find a wire diagram off the factory stereo so you can wire the factory speakers up to your head unit also you will need to mount the new stereo to the dash which is simple a mount frame should be in the new head unit box

    Oct 05, 2010 | 2001 Mercedes-Benz C-Class

    1 Answer

    My 2005 Montero with a Infinity stereo system has a blown woofer how can I fix this with after market speakers


    Check to see what type of stereo head unit is installed in the car first and foremost... next you're going to want to find out if the unit is powered and sending power to the speakers.

    After you figure this out, you can then go about picking out a replacement set of speakers for your car. You also need to decide if you want to upgrade being that you'll be spending money on new speakers anyway. Audio is a very subjective matter so what sounds good to you might not sound good to the next person which is why I recommend you go to a stereo shop and listen to the speakers yourself with all the settings on the head unit its hooked up to flat (i.e. the EQ flat, the fader off, the balance set to the center, and soforth) as this will give you a better gauge of how the speaker sounds by itself without any help from the head unit.

    Infinity is a decent brand and Im sure you'll be able to find replacements of the OEM speakers relatively easily if you want to go that route. You could remove the speaker, and probably check out Crutchfield which stocks most of the infinity line for your specific model of Infinity woofers.


    Removal is a simple task of removing door panels if its in the doors, and removing some screws and undoing some wire connectors. All you'll need are some screwdrivers and possibly some pliers.

    Schematics and specifications of your stereo system should be easy enough to find online by doing a search with google or bing.

    hope that helps! =)

    Oct 17, 2009 | 2005 Mitsubishi Montero

    2 Answers

    How to remove 2001 hyndai sonata audio system


    Instructions
    Things You'll Need:
    • Screwdrivers
    • Wiring harness adaptor
    • Hyundai radio adaptor kit
    1. Open the coin holder and remove the two screws at the front. Pry the trim from around the gearshift lever and unhook the power wire to the cigarette lighter.
    2. Locate and remove the two screws from the bottom of the radio trim panel. Look for the screws, attached to a rod, below the glove box. Unhook the cable from the rod and pull the rod free.
    3. Place the shifter into "D" and slide the radio trim panel away from the dash. Locate the four screws at the front and sides of the stereo and remove them.
    4. Pull the stereo out of the Hyundai Sonata dash and disconnect the wires from the back of the unit. Connect the wiring harness adaptor to the original harness.
    5. Slide the new head unit into the Hyundai radio adaptor kit. Attach the wiring harness adaptor and antenna wire to the back of the new head unit and push the entire assembly into the dash.
    6. Secure the stereo in place with the four front and side screws and turn it on. Verify all of the speakers and features are working. Reattach the radio trim panel, insert the rod back into cable assembly and secure the trim around the gear shift.

    In here you can find tips about remove radio...
    - Hyundai Car Stereo removal
    - Stereo Removal Hyundai (buy)

    I really hope help you with this (remember rated this help). Good luck.

    Oct 01, 2009 | 2001 Hyundai Sonata

    1 Answer

    How do u remove the rear drivers side door panel on an 01 olds aurora?


    1. Remove the two visible screws on the hinge side of the door panel 2. Remove the two (or three) visible screws on the latch side of the door panel. 3. Remove the screw in the plastic door pull recess. 4. Remove the door pull recess by extending the door pull (like you are opening the door), lifting the end of the recess that the screw was removed from and pulling the recess forward toward the door hinges. 5. Lift the plastic cap off the screw head in the 'cup' located at the rear of the power window control panel on the door and remove the screw. 6. Lift the power window control panel out of the door panel ( it puts up a fight) and disconect the two power plugs on the bottom of the assembly. 7. Using a stiff putty knife or a similar tool pry the bottom of the door panel from the door, it is secured by several plastic push in thingies. 8. Disconect the light bulb from the lower left hand corner of the door panel by twisting it a half turn and pulling straight out. 9. At this point the panel should be connected to the door at the top of the panel only. 10. There is probably a better technique but I lifted and pryed and twisted the door panel until the fasteners from Hell that connect the top of the panel to the door decided to release the panel (all the while making sure I was gentle enough not to damage the panel or the fasteners). 11. I didn't need to remove the mirror but I did notice a screw head leading to the mirror assembly that was exposed after the panel was removed. 12. While you have the panel removed you might want to lubricate as many mechanisms as you can while you have them exposed.

    You can follow these instructions witch are for the front door as they are pretty much the same to undo let me know if you need further assistance ok

    Aug 17, 2009 | Oldsmobile Aurora Cars & Trucks

    2 Answers

    Remove front door panel on 1995 merc grand marquis


    http://www.autoclinix.com/Mercury/Front%20Speakers2.htm

    Dec 27, 2008 | 1995 Mercury Grand Marquis

    1 Answer

    Stereo light bulb replacement.


    deep inside head unit at front is the led to replace .. likely soldered into a board there as a non replaceable part ..remove head unit ..disassemble to get behind front panel...good luck..maybe this is not a worthwhile project money/ time wise.... my 2 cents

    Oct 27, 2008 | 2000 Chevrolet Silverado

    Not finding what you are looking for?

    Open Questions:

    See all 1990 Nissan Pulsar Questions

    1990 Nissan Pulsar Logo

    Related Topics:

    129 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Phil Lovisek
    Phil Lovisek

    Level 3 Expert

    726 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...