Question about 2001 Ford Windstar

Open Question

2001 ford windstar body control module location

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: location of ignition control module

It does not have an ignition control module.
The electronic ignition (EI) for the 4.0L engine consists of the following components:
Crankshaft position sensor (CKP sensor) and 36 minus 1 tooth trigger wheel.
Ignition coil .
powertrain control module (PCM) .
Related wiring.
The PCM controls the firing of the coil based on the signal from the crankshaft position sensor.
The crankshaft position sensor (CKP sensor) is a variable reluctance-type sensor, triggered by a 36 minus 1 tooth trigger wheel configuration machined into the rear of the crankshaft vibration damper. The signal generated by this CKP sensor is called a CKP signal. The CKP signal provides the base timing and rpm information to the powertrain control module (PCM). Base timing is set at 10 degrees BTDC and is not adjustable.
If vehicle has no spark then turn key to on position,check engine light should come on.As you start cranking engine it should go out while cranking after about 10 secs. it should come back on(while cranking). If it come on then the PCM sees the signal,if it does not then PCM is not seeing it and this is your problem,either the CKP sensor or the wiring to it.

Posted on Mar 16, 2009

chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

  • 38 Answers

SOURCE: fue pump location 2001 ford windstar

Probaly in the fuel tank

Posted on Jul 19, 2009

  • 270 Answers

SOURCE: power steering pump on a 2001 ford windstar

There is a special tool for that. It should be available at most auto parts stores.

Posted on Oct 17, 2009

  • 200 Answers

SOURCE: I am looking for a Gem Module or a Body Control

Sodometer and speedometer could be vehicle speed sensor. ABS module could cause the other symptom. Do a search on the part number they say is bad. Try this site for repairs http://www.bba-reman.com/catalogue/Products.aspx?category=811

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the body control module (bmc) located at in a Ford Windstar 2002?


pretty sure this vehicle does not have a BCM. most fords don't. there is a module built onto the back of the inside fuse block that is more or less the same thing. a real pain to get out of the vehicle.

Apr 29, 2015 | Ford Cars & Trucks

1 Answer

Where is the idle air control valve wiring harness located on a 2001 ford windstar


idle-air-control-valve-wiring-harness-prnuo4xtyj5wakm52h23pt2g-5-0.jpg

idle-air-control-valve-wiring-harness-prnuo4xtyj5wakm52h23pt2g-5-2.jpg


idle-air-control-valve-wiring-harness-prnuo4xtyj5wakm52h23pt2g-5-9.jpg

idle-air-control-valve-wiring-harness-prnuo4xtyj5wakm52h23pt2g-5-14.jpg this is the idle air control and the plug the wires may not be the same color the valve is located on the throttle body the photo's will make it easier to find it

Apr 05, 2015 | 2001 Ford Windstar LX

1 Answer

With a fuse number of door opener?


There isn't one. The opener is controlled by the Body control module. The BCM is probably bad for the opener.

Aug 20, 2014 | 2001 Ford Windstar

1 Answer

Where is the fuse box location for 2001 windstar and is the windshield washer fuse named


the washer pump is not fused directly, the pump operates through a central module called the BCM (body control module), so if the power windows work and the wipers work the problem is not loss of power to the system, it is either a defective wiper switch (most common) or it is a defective washer pump motor. My experience? 35 years as a Ford dealer technician

Aug 03, 2010 | 2001 Ford Windstar

1 Answer

2001 ford windstar wont run


Doubtful, the pcm controls security in you vehicle. If you replace the pcm then it would likely need to be reprogramed.

Mar 27, 2010 | 2001 Ford Windstar

2 Answers

Were is the computer module in 2003 ford windstar


passenger side, connector is uinder the hood, pulls out from inside van.it is very hard to see, the connector is huge so look with a flashlight.

Mar 05, 2010 | 2003 Ford Windstar

1 Answer

Ford Windstar transmission shifting too soon


yes , the kick down cable is adjustable on a 2001 Windstar. The linkage is located in the throttle body.

Nov 24, 2008 | 2001 Ford Windstar

1 Answer

Need to know where the power control module location is.


the PCM is located under the hood,on the left side,at rear on fire wall.look in at the back looking over pass side strut tower.

Nov 18, 2008 | 2001 Ford Windstar

Not finding what you are looking for?
2001 Ford Windstar Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...