Question about Cars & Trucks

Open Question

2001 mercury villager sport 3.3 codes: p0300 andpo325

The engine lopes at idle ans runs rough,check engine light is blinking

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 407 Answers

SOURCE: check engine light on,running rough and stalling.

means you have multiple misfires (po300) the other codes are lean codes, possiable tune up , bad injector, fuel pump,

Posted on May 07, 2009

csmock132
  • 4669 Answers

SOURCE: check engine light on,running rough code P0172

When I see all these codes i instantly think of two things. Vacuum leak especially intake manifold gaskets and Mass air flow sensors. Spray the engine with carb cleaner when its running and see if you get it to rev up,run rough or run different. Next unplug the MAF and drive the car, see if it runs normal.

Posted on Jun 02, 2009

  • 22 Answers

SOURCE: 2001 Forester, Rough idle and engine loping driving at low rpm

I had a similar problem on my 2002 Impreza RS 2.5 (same engine and engine control system). In my case it was the O2 sensor on the intake manifold. This happened at 34,xxx mi. so it was covered by the warranty. Replacing the part is very easy. (two bolts and a wiring harness). Obviously I would start simple and cheap and work your way to expensive and difficult.
From my understanding its all caused from the engine missfiring. If its been a while or never, I'd change the spark plugs first. (stick with the Subaru Parts plugs, I went after market and the dealer claimed the plugs were not the correct "temperature" and had to pay for the new plugs and install although they did it without my permition. Thats a whole nother story).
Could also be the manifold pressure sensor.
Either 02 or manifold pressure sensor may cause intermitent check engine light.
Where I live Brookline,MA , Autozone will run a free diagnostic on your car by hooking up to your ECU and will give you the trouble codes and possible remidies. Of course there are no guarentee's but it will point you in the right direction.
Good Luck

Posted on Jun 18, 2009

csmock132
  • 4669 Answers

SOURCE: code p0300 and p1406

P0300 is misfire and p1406 is EGR. It sounds like you have a chunk of carbon stuck in the EGR valve. Remove the valve and clean the carbon from the valve, bottom side. Then install a screened gasket so it won't happen again.

Posted on Jun 24, 2009

  • 1915 Answers

SOURCE: Missing, running very rough at

the P0011 and P0022 are the camshaft sensors (both sides) are over advanced--common problem on Fords, and is usually a defective VCT solenoid (variable cam timing solenoid)-it will cause your other codes (P0300 random misfire), P0305 (#5 cylinder), P0307 (#7), P0316 (misfire at startup)-P0171 is a lean condition on side 1, where #1 plug is located (look for a vacuum leak, but a faulty VCT could also cause this)-is there any chance the last oil change set this off? The proper viscosity is very important and may have caused these codes.

The P2198 is O2 sensor signal stuck rich bank 2 sensor 1. Has the engine or sensors recently gotten a bath in oil (seafoam?)-this code indicates something of possibly an over zealous maintenance procedure could have damaged maybe the MAP sensor, or more.... Unfortunately, you have a lot of company. At least you didn't crack a piston or hydrolock the engine. Seafoam is pale oil, naptha, and alcohol. With more detail there should be a reason for all those somewhat related codes-post more information.

Posted on Jan 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Running rough& stalling


Brenda, this could be a lot of different things to cause hard start and stalling. Faulty crank sensor, idle air control valve, EGR, vacuum leak, injectors, fuel pump, ignition circuit, distributor faulty,plugs,wires,plugged exhaust, etc. Find a good technician check the codes and have them diagnose and give an estimate on repair. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info.
No Start Engine Stalls Mercury Villager Common Engine Problems
Nissan Quest Mercury Villager Starting Stalling Problems
http://forums.nicoclub.com/1996-nissan-altima-runs-rough-and-stalls-t162761.html

May 06, 2016 | Cars & Trucks

1 Answer

Starts up but runs rough, exhaust smells, and when you give it gas it wants to shut off.


How To Fix P0300 random misfire codes in your car ...

? 2:56
https://www.youtube.com/watch?v=OyvdWeyDHf4
Feb 5, 2010 - Uploaded by Scotty Kilmer
Scotty Kilmer, mechanic for the last 46 years and counting, shows how to fix your car if the check engine light ...

P0300 - OBD-II Trouble Code - RepairPal

repairpal.com > Encyclopedia > OBD II Codes
OBD II Fault Code. OBD II P0300. Fault Code Definition. Random, Multiple MisfireDetected. Symptoms. Check Engine Light flashing; Rough running, hesitation ...

P0300 - Check Engine Light Diagnostic Trouble Code ...

https://www.engine-light-help.com/P0300-check-engine-light.html
The misfire detection monitor, a software strategy built into the computer, is designed to detect an engine misfire. The computer can also normally identify the ...

Random-Misfire Page

www.random-misfire.com/

Jan 24, 2016 | Cars & Trucks

1 Answer

How do i fix my Mercury Villager 2002 with random misfire?


How to Fix error code P0300 for random misfires on your car ...

diy-auto-repair.wonderhowto.com/.../fix-error-code-p0300-for-random-...
Oct 15, 2010 - How to Fix error code P0300 for random misfires on your car ... amisfire (code P0304) on a 1999 Mercury Villager 3.3L ยท How to Fix error code P0500 ... I reset my codes and it ran fine for a couple of days, then I started getting ...

(code P0305) on a 1999 Mercury Villager 3.3L - auto repair

diy-auto-repair.wonderhowto.com/.../troubleshoot-misfire-code-p0305-1...
Sep 7, 2010 - The vehicle is a '99 Mercury Village, 3.3L, with 150000 miles on it. The chief ... How to Fix error code P0300 for random misfires on your car ...

2000 Villager Misfire - Car Forums and Automotive Chat ...

www.automotiveforums.com > ... > Mercury > Villager
May 24, 2010 - 2000 Villager Misfire Villager Car Forums. ... i was told that the 3.3L engines of 1999-2002 nissan quests/ mercury villagers are INTERFERENCE engines! ... Hope the following may help, and I will post if my last fix works. ... I have a 1999mercury villager that is showing a random multiple cylinder misfire ...

Rough Idle - 2000 Mercury Villager - RepairPal

repairpal.com > Questions > Mercury > Villager > 2000 Mercury Villager
Repair the code issue, because your Villager has OBD-II which is a very helpful Diagnostic system. Upvote (4) ... My 1999 Villager was running poorly; rough idle, lack of power at highway speeds and the engine problem light indicated random miss-fire, etc. I had new spark ... Have code po306 cylinder 6 misfire detected.

P0301 - OBD-II Trouble Code - RepairPal


Dec 17, 2015 | 2002 Mercury Villager

1 Answer

I have 01 trooper replaced gas cap now check engine light off, but I have a p0300 code will it pass smog.?.


Many states will not pass a vehicle with a check engine light.

The P03000 code you have has little to do with the gas cap, rather it is a random misfire code. read more about this code and possible fixes in the link below. Good luck!

http://www.obd-codes.com/p0300

Jul 24, 2015 | 2001 Isuzu Trooper

1 Answer

Idling rough


misfire spark plugs coils wires did you wash engine water gets in under the intake to the plugs first if with a scanner check codes p0300 change plugs p0301 or 2 or 3 or 4 its one of the cylinders i would try just changing all the plugs first and start from there

Apr 18, 2014 | 2000 Kia Sportage

1 Answer

2001 mercury sable lopes at idle, misses on acceleration adn engine light blinks. Computer logs misfire on cylinder1 and 5. Possible fixes? Changed plugs ran ok two weeks.


CHECK THE COILPACKS. YOU MAY HAVE A COIL THAT IS NOT PRODUCING A HOT ENOUGH SPARK ON TWO CYLINDERS. I HOPE THIS HELPS. THANKS FOR USING FIX-YA.

Aug 26, 2009 | 2001 Mercury Sable

1 Answer

Ran real low on gas


it sounds like you plugged your injecters put some STP gas treatment with injecter cleaner into the gas tank with at least a half a tank of gas and then finish filling it up and if this helps also replace the fuel filter

Feb 01, 2009 | 2001 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...