Question about Lincoln Cars & Trucks

1 Answer

Need instructions on how to remove and relpace blend door actuator and install on a 1997 lincoln contiental

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Lincoln Master
  • 76,848 Answers

Duplicate question

Posted on Oct 30, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 97 Lincoln Contiental Drivers door ajar message

It is a sticky sensor in the door latch mechanism. Spray it w/ WD-40 and follow up with a dose of silicone spray. Open/close doors several times and it should be ok. If you have a problem with 1 door the other 3 are sure to follow---DO THIS TO ALL 4 DOORS!!!!!!!!!

Posted on Dec 22, 2008

  • 1 Answer

SOURCE: constant high heat

on climate control press off and heat button and let go quickly. Then press automatic. The display will start rotating eventually displaying a code 025,125 , 024 etc. Then press defrost to stop. You may hear blend door operating atb that time. It worked for my climate control.

Posted on May 06, 2009

warlock61
  • 659 Answers

SOURCE: need to locate blend door actuator 98 lincoln

it is located on top of the heater box assy behind the dash just to the left of of the glovebox if you open the glovebox and look to the left you can see it

Posted on Jul 11, 2009

  • 5 Answers

SOURCE: how to replace blend door actuator in a ford

I recently did mine, I hear you can do it without taking the entire dash apart but I had no luck with it myself. I have to get ready for work but, on mine it was located down and to the left of the radio. its a white box...are you hearing a clicking noise or something? I had to roll the entire dash back and it was still a major pain getting it out.

Posted on Dec 07, 2009

  • 1 Answer

SOURCE: how do I remove the dash to replace blend door

blender door on a 2003 grand marquis blows only hot air the ac works

Posted on Apr 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

"Relearning" process for re-installation of blend door actuator motor (if necessary) on 1997 Ford F150.


There is no process, just make sure the battery negative cable is disconnected before install the part.

Apr 19, 2017 | Ford Cars & Trucks

1 Answer

How to replace the door blend actuator on 2009 lincoln mks


Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage
  1. Remove the 2 lower steering column opening cover bolts.
  1. Detach the lower steering column opening cover.
  1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
  1. Position the instrument panel wire harness away from the LH temperature blend door actuator.
  1. Remove the 3 LH temperature blend door actuator screws.
  1. Disconnect the LH temperature blend door actuator electrical connector.
  1. Remove the LH temperature blend door actuator.
  1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage
  1. Disconnect the glove compartment damper from the glove compartment.
  1. Remove the glove compartment.
  1. Remove the RH lower instrument panel insulator.
  1. Remove the RH lower floor console trim panel.
  1. Remove the 3 RH temperature blend door actuator screws.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  1. Remove the RH temperature blend door actuator.
  1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
  2. Mode Door Actuator - Defrost/Panel/Floor Door
  3. Removal and Installation
    NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
    NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
    Mode door actuator and linkage
    1. Remove the 3 defrost/panel/floor mode door actuator screws.
    1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
    1. Remove the defrost/panel/floor mode door actuator.
    1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
    Mode door actuator linkage only
    1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
    Mode door actuator and linkage
    1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.

Nov 10, 2016 | 2009 Lincoln MKS

1 Answer

How to remove console 97 lincoln continental


I replaced the blend door actuator (BDA)a couple of years ago. It is a challenging task, but if you are young with good eyesight, not too large, and patient, you can do it WITHOUT the enormous hassle of removing the console, which is a two man job. You need good illumination, perhaps a small mirror, possibly a camera to take some closeups of exactly how the BDA is attached, and a flexible shaft nut driver. Not too bad of a job, IF you study and plan the task with some care. I would never recommend removing the console. That is just asking for trouble and frustration, and your car will be out of commission until the console is PROPERLY connected. Good luck.

Jul 10, 2014 | 1997 Lincoln Continental

1 Answer

HOW TO REPLACE THE BLEND DOOR ACTUATOR


i've done this and i'm sorry you have to - it's not quick and easy. the dash must be removed. the module sits on top of the heater box. i found a Lincoln shop manual for the 97 town car on ebay that was very helpful with step by step disassembly and some pictures. i'd recommend it for sure.
good luck

Nov 10, 2012 | 1997 Lincoln Town Car

1 Answer

How to replace blend door actuator on a 1997 lincoln contiental


The problem is most likely not just the blend door actuator, the electric motor actuators fais to move the door because the blend door warps and then it takes an excessive amount of power to move it or it will not move at all, which on this model is the case most of the time. The replacement of these parts requires the dash top be removed from the car, to do this job you need access to the factory service manuals. You can download them for a reasonable fee here. This is a 12-14 hour job at home for an amateur

Oct 30, 2012 | Lincoln Cars & Trucks

1 Answer

My 2004 Avalanche ' heating system will not heat. No matter what the setting it either blows no air or cold air and it is 25 degrees outside so this is a problem. The engine is up to temp and I have tried...


The most likely cause is a failed blend door actuator; however I recommend a little troubleshooting. First, can you hear a clicking sound behind the dash when you turn the setting to hot? If yes, it is certainly the actuator stripping its gears. If not, check to make sure the heater hoses are both hot as they connect to the heater core at the firewall (in the engine compartment). If one or both of the hoses do not get hot, there is a blockage caused either by an air bubble or a stuck water control valve in the heater hose. If the hoses are both hot, the indication is again the blend door actuator.

Below are instructions for replacing the actuator. Look at the diagrams carefully--the big arrows point to the front of the truck and the actuator is on the side of the heater box above the outlet duct that runs to the driver's side of the floor. Also, the actuator is expensive, so I recommend you make sure it's bad and shop around a bit to get a good price. To check out the actuator, first see if you can turn the blend door by hand. If you can't turn it, maybe it's jammed. Also, reconnect the actuator after removing it and see what it does when you turn the heater to hot.

Removal & Installation
  1. Remove the floor air outlet duct extension (1) from the floor duct (2).

    jturcotte_393.gif

Fig. Remove the floor air outlet duct extension (1) from the floor duct (2)


Disconnect the electrical connection at the blend door actuator (#10 in pic below). jturcotte_394.gif

Fig. Blend door actuator and related components


Remove the blend door actuator mounting screws from the HVAC module.


Remove the blend door actuator as an assembly with the actuator cam.
jturcotte_396.gif

Fig. Remove the blend door actuator mounting screws from the HVAC module



To install:

  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam

  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).

  3. Connect the electrical connection at the blend door actuator (10).
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).


Picture of actuator:


jturcotte_57.jpg

Dec 07, 2010 | 2004 Chevrolet Avalanche

1 Answer

Does blend door actuator once changed in 1997 lincoln mark 8 require reprograming?


no,it should work ok,,if it is not,the blend door itself maybe the problem not the actuator.

May 31, 2010 | 1997 Lincoln Mark VIII

1 Answer

I have to replace the ac door actuator motor behind the ash tray


are you sure it is not the temp control on the heater control panel that's bad?
please rate if this solves your issue.

A/C Electronic Blend Door Actuator The A/C electronic blend door actuator is located on the rear of the A/C evaporator housing assembly.
  • Its function is to move the A/C air temperature control door on command from the control assembly.
  • The A/C electronic blend door actuator contains a reversible electric motor and a potentiometer. The potentiometer wiper is connected to the actuator output shaft and moves with the output shaft to indicate the position of the A/C air temperature control door.
  • A 5 volt signal is applied to the ends of the potentiometer. The voltage available at the wiper indicates the position of the potentiometer. The expressed value of the actuator wiper voltage is sent to the control module and is matched with the wiper voltage of the module potentiometer. The printed circuit board then drives the actuator motor in whichever direction is necessary to make the actuator wiper voltage agree with the control module wiper voltage.
A/C Electronic Blend Door Actuator
Removal
  1. Disengage two push pins retaining instrument panel insulator to instrument panel. Disconnect courtesy lamp from instrument panel insulator.
    1. Remove floor console. Refer to Section 01-12 .
    1. Working from under instrument panel, remove two retaining screws and metal cover from A/C evaporator housing.
    1. Remove A/C electronic blend door actuator electrical connector.
    1. Remove three remaining retaining screws from A/C electronic blend door actuator.
    1. Pull the A/C electronic blend door actuator away from the A/C evaporator housing for a distance of approximately 25 mm (1 inch) to disengage it from the A/C air temperature control door.
5728f0a.gif

May 24, 2009 | 1997 Lincoln Continental

2 Answers

Need to replace ac blend door motor inside dashby glove box does dash have to come out and how much trouble is it?


the bummer is removing instrument panel. big job.

A/C Electronic Blend Door Actuator Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove instrument panel (04320). Refer to Section 01-12 .
  1. Remove four A/C electronic blend door actuator retaining screws.
  1. Remove A/C electronic blend door actuator.


2c01b1e.gif
Item Part Number Description 1 18471 Heater Air Plenum Chamber 2 42141-S8 Screw (4 Req'd) 3 — A/C Electronic Blend Door Actuator 4 — A/C Air Temperature Control Door Shaft (Part of 18471) 5 19D842 A/C Air Temperature Control Door

Feb 23, 2009 | 1997 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...