Question about 1993 Chevrolet Lumina

1 Answer

Soft (no) brakes

My brakes have been barely working lately and they feel soft. I just bled them and I thought I did it right, but now the brakes aren't working at all. Should I just bleed them again or what?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

You might have to try bleeding the whole system of the old fluid. you might have moisture in it somewhere.

Posted on Jan 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced disc brake pads, rear shoes. wheel cylinder,master cylinder, power brake booster all new. Question: My brake pedal is not solid,goes low to the floor almost. I have bled the master cylinder 1st,...


Check your lines going to the brakes the rubber hose on the 1993 chevy have a tendancy to crack and brake are you using an excess of brake fluid

Sep 12, 2011 | 1993 Chevrolet C1500

1 Answer

I replaced the drivers side rear caliper and brakes feel soft and slowly go to close to floor when pressed. Bled caliper several times but pedal still doesnt feel right. There doesnt seem to be any more...


Check line on caliper you replaced it may not be tight enough and letting air into system.if this is not your problem rebleed brakes do not pump brake pedal while bleeding brakes. if you are not aware of how to properly bleed brakes email me at ken17402@msn.com and I will fill you in.

Nov 20, 2010 | Volkswagen Rabbit Cars & Trucks

2 Answers

Just replaced rotors, calipers, caliper brackets, and pads. Bled all four wheels, starting with the farthest away from the master cylinder working my way to the closest. Brake pedal feels firm when car...


Bleed with the car running and make sure all the air is out. Now make sure there is no leak and the pad contact are adjusted without much gap so that the calipers hold on. make sure the servo assist is correct, if so and the master cylinder was set right , it must work. Please recheck all your work once again to trim up.

Sep 28, 2010 | Nissan Xterra Cars & Trucks

1 Answer

When push brakes you have to push really hard to make them go in then the truck barely stops. Replaced the MC and bled the brakes now every time push brakes truck acts like its going to die. Brake light...


Sounds like you will have to bleed your brakes again, but thats not the problem og hard brake peddle, need to check your power brake booster, sit right in back of master cylinder, check make sure it has vacum going to it, also to test it with engine off, press on brake peddle three time, then state engine with foot on peddle, peddle should go down a few inches, also with engine of peddle should feel soft for three pumps, if you have none of this , power brake booster is bad.

Jul 04, 2010 | 1995 Toyota 4Runner

1 Answer

I have a 2000 chevy blazer. had to short fix left rear brake line with hose and clamps. bled air from that side, brakes were soft in the pedal. checked right rear for any air had none. brakes still feel...


do not drive the vehicle. remove the hoze. replace it with steel line. rubber hoses are not meant for the high pressures of brake lines. it is expanding when you press the brake pedal. very unsafe.

Mar 23, 2010 | 2000 Chevrolet Blazer

3 Answers

While driving my 1994 Honda Accord the brakes went out. I can only get the car to stop if I press the brake pedal all the way down to the floor. When the car is shut off and I pump the brake pedal, I can...


There may be air in the lines. Bleed all your brakes starting at the farthest wheel from the resevoir, and finishing at the closest one. Try the pedal after its bled. If the pedal still feels soft or travels to the floor there may be a pinhole leak that may be spraying on the underbody of the car, or the seals in the master cylinder are gone filling the vacuum booster(if equipped). Air compresses more than oil so if bleeding works that may be the problem.

Feb 21, 2010 | 1994 Honda Accord

Not finding what you are looking for?
1993 Chevrolet Lumina Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...